The DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index.
Three‐dimensional printing of porous ceramic scaffolds for bone tissue engineering
Open accessAbstract
This article reports a new process chain for custom‐made three‐dimensional (3D) porous ceramic scaffolds for bone replacement with fully interconnected channel network for the repair of osseous defects from trauma or disease. Rapid prototyping and especially 3D printing is well suited to generate complex‐shaped porous ceramic matrices directly from powder materials. Anatomical information obtained from a patient can be used to design the implant for a target defect. In the 3D printing technique, a box filled with ceramic powder is printed with a polymer‐based binder solution layer by layer. Powder is bonded in wetted regions. Unglued powder can be removed and a ceramic green body remains. We use a modified hydroxyapatite (HA) powder for the fabrication of 3D printed scaffolds due to the safety of HA as biocompatible implantable material and efficacy for bone regeneration. The printed ceramic green bodies are consolidated at a temperature of 1250°C in a high temperature furnace in ambient air. The polymeric binder is pyrolysed during sintering. The resulting scaffolds can be used in tissue engineering of bone implants using patient‐derived cells that are seeded onto the scaffolds.This article describes the process chain, beginning from data preparation to 3D printing tests and finally sintering of the scaffold. Prototypes were successfully manufactured and characterized. It was demonstrated that it is possible to manufacture parts with inner channels with a dimension down to 450 μm and wall structures with a thickness down to 330 μm. The mechanical strength of dense test parts is up to 22 MPa. © 2005 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2005
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Hutmacher, D. W., Schantz, T., Zein, I., Ng, K. W., Teoh, S. H., & Tan, K. C. (2001) · Journal of Biomedical Materials Research · doi:10.1002/1097-4636(200105)55:2<203::aid-jbm1007>3.0.co;2-7 · Cited by 1,409
The Design of Scaffolds for Use in Tissue Engineering. Part II. Rapid Prototyping Techniques
Yang, S., Leong, K.-F., Du, Z., & Chua, C.-K. (2002) · Tissue Engineering · doi:10.1089/107632702753503009 · Cited by 729
Mechanical Testing of Bone and the Bone-Implant Interface
(1999) · CRC Press eBooks · doi:10.1201/9781420073560 · Cited by 709
Taboas, J. M., Maddox, R. D., Krebsbach, P. H., & Hollister, S. J. (2003) · Biomaterials · doi:10.1016/s0142-9612(02)00276-4 · Cited by 691
Gauthier, O., Bouler, J.-M., Aguado, E., Pilet, P., & Daculsi, G. (1998) · Biomaterials · doi:10.1016/s0142-9612(97)00180-4 · Cited by 614
Scaffold development using 3D printing with a starch-based polymer
Lam, C. X. F., Mo, X. M., Teoh, S. H., & Hutmacher, D. W. (2002) · Materials Science and Engineering: C · doi:10.1016/s0928-4931(02)00012-7 · Cited by 614
Use of stereolithography to manufacture critical‐sized 3D biodegradable scaffolds for bone ingrowth
Cooke, M. N., Fisher, J. P., Dean, D., Rimnac, C., & Mikos, A. G. (2003) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.10485 · Cited by 571
Park, A., Wu, B., & Griffith, L. G. (1998) · Journal of Biomaterials Science, Polymer Edition · doi:10.1163/156856298x00451 · Cited by 322
Fabrication of 3D chitosan–hydroxyapatite scaffolds using a robotic dispensing system
Ang, T. H., Sultana, F. S. A., Hutmacher, D. W., Wong, Y. S., Fuh, J. Y. H., Mo, X. M., Loh, H. T., Burdet, E., & Teoh, S. H. (2002) · Materials Science and Engineering: C · doi:10.1016/s0928-4931(02)00010-3 · Cited by 278
Roy, T. D., Simon, J. L., Ricci, J. L., Rekow, E. D., Thompson, V. P., & Parsons, J. R. (2003) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.10582 · Cited by 262
Landers, R., & Mülhaupt, R. (2000) · Macromolecular Materials and Engineering · doi:10.1002/1439-2054(20001001)282:1<17::aid-mame17>3.0.co;2-8 · Cited by 261
Hydroxyapatite implants with designed internal architecture
Chu, T. G., Halloran, J. W., Hollister, S. J., & Feinberg, S. E. (2001) · Journal of Materials Science Materials in Medicine · doi:10.1023/a:1011203226053 · Cited by 256
Wilson, C. E., de Bruijn, J. D., van Blitterswijk, C. A., Verbout, A. J., & Dhert, W. J. A. (2004) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.20015 · Cited by 184
Weiss, P., Obadia, L., Magne, D., Bourges, X., Rau, C., Weitkamp, T., Khairoun, I., Bouler, J. M., Chappard, D., Gauthier, O., et al. (2003) · Biomaterials · doi:10.1016/s0142-9612(03)00335-1 · Cited by 160
Qing-kun, X. (2005) · Journal of Changsha University · Cited by 148
Roy, T. D., Simon, J. L., Ricci, J. L., Rekow, E. D., Thompson, V. P., & Parsons, J. R. (2003) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.20034 · Cited by 145
Charrière, E., Lemaître, J., & Zysset, P. K. (2002) · Biomaterials · doi:10.1016/s0142-9612(02)00406-4 · Cited by 120
(1999) · CRC Press eBooks · doi:10.1201/9781420073560-10 · Cited by 57
Cited by
Polymers for 3D Printing and Customized Additive Manufacturing
Ligon, S. C., Liska, R., Stampfl, J., Gurr, M., & Mülhaupt, R. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00074 · Cited by 3,741
Three-Dimensional Scaffolds for Tissue Engineering Applications: Role of Porosity and Pore Size
Loh, Q. L., & Choong, C. (2013) · Tissue Engineering Part B: Reviews · doi:10.1089/ten.teb.2012.0437 · Cited by 2,668
Additive manufacturing: technology, applications and research needs
Guo, N., & Leu, M. C. (2013) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-013-0248-8 · Cited by 2,073
Bone tissue engineering using 3D printing
Bose, S., Vahabzadeh, S., & Bandyopadhyay, A. (2013) · Materials Today · doi:10.1016/j.mattod.2013.11.017 · Cited by 1,866
Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences
Gross, B. C., Erkal, J. L., Lockwood, S. Y., Chen, C., & Spence, D. M. (2014) · Analytical Chemistry · doi:10.1021/ac403397r · Cited by 1,746
Metadata
- Authors
- Seitz, H., Rieder, W., Irsen, S., Leukers, B., & Tille, C.
- Venue
- Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Publisher
- Wiley
- Published
- 2005-06-24
- Volume
- 74B
- Issue
- 2
- Pages
- 782-788
- ISSN
- 1552-4973 (ISSN-L)
- 1552-4981
- OpenAlex
- W2025216077
- Cited by
- 742
- References
- 18
- FWCI
- 14.46
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.