The DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index.
Ultra‐high‐modulus linear polyethylene through controlled molecular weight and drawing
Abstract
Recent work is presented on the plastic deformation of linear polyethylenes. This work demonstrates the importance of molecular weight and initial morphology in determining the drawing behavior, and shows that by appropriate choice of these two factors a substantial increase in draw ratio and hence stiffness can be achieved over conventionally‐oriented polyethylenes. Under optimum conditions a modulus of approximately 700 Kbar was obtained at a draw ratio of ∼30. These very high modulus materials displayed an extensibility to break of at least 3 percent and a strength of about 4 Kbar. In some cases they also exhibited very high melting points (∼139°C) and exceptionally good thermal stability.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Increasing the degree of orientation increases the Young's modulus.”
In the citing paper
“HDPE elongated in the solid state exhibits a strong dependence of the Young's modulus on molecular orientation, for instance as reported by Capaccio and Ward [34] and Capaccio et al [35].”
Citations
Cites
Longitudinal Acoustical Vibrations of Finite Polymethylene Chains
Schaufele, R. F., & Shimanouchi, T. (1967) · The Journal of Chemical Physics · doi:10.1063/1.1712428 · Cited by 349
Capaccio, G., & Ward, I. M. (1974) · Polymer · doi:10.1016/0032-3861(74)90038-x · Cited by 326
Self-citationThe strength and stiffness of polymers
Frank, F. C. (1970) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1970.0170 · Cited by 319
Calculations of elastic moduli of polymer crystals: I. Polyethylene and nylon 66
Treloar, L. R. G. (1960) · Polymer · doi:10.1016/0032-3861(60)90012-4 · Cited by 218
Properties of Ultra-high Modulus Linear Polyethylenes
CAPACCIO, G., & WARD, I. M. (1973) · Nature Physical Science · doi:10.1038/physci243143a0 · Cited by 174
Self-citationThe cold-drawing of high density polyethylene
Andrews, J. M., & Ward, I. M. (1970) · Journal of Materials Science · doi:10.1007/bf00550003 · Cited by 166
Self-citationCrystal orientation and some properties of solid-state extrudate of linear polyethylene
Imada, K., Yamamoto, T., Shigematsu, K., & Takayanagi, M. (1971) · Journal of Materials Science · doi:10.1007/bf00550308 · Cited by 156
Stress-optical properties of amorphous polyethylene terephthalate fibres
Pinnock, P. R., & Ward, I. M. (1966) · Transactions of the Faraday Society · doi:10.1039/tf9666201308 · Cited by 141
Self-citationDulmage, W. J., & Contois, L. E. (1958) · Journal of Polymer Science · doi:10.1002/pol.1958.1202811703 · Cited by 119
Mechanical properties of ultra‐oriented polyethylene
Weeks, N. E., & Porter, R. S. (1974) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1974.180120401 · Cited by 112
Research works printed but not linked: 7
- L. A.Feldkamp G.Venkateraman andJ. S.King Proc. of Symp. Copenhagen May 1968 Vol. II p.159 LAEA Vienna (1968).
- Sakurada I., 1966, J. Polym. Sci., 15, 75
- A. G.Gibson I. M.Ward B. N.Cole andB.Parsons J. Mat. Sci.(in press).
- J. B.Smith A. J.Manuel andI. M.Ward Polymer(in press).
- J. S.Foot Ph.D. thesis Bristol University (1972).
- G.CapaccioandI. M.Ward Polymer(in press).
- Clark E. S., 1974, ACS Polym. Prepr., 15, 153
Cited by
Strength and toughness of crystalline polymer systems
Galeski, A. (2003) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2003.09.003 · Cited by 614
Influence of molecular weight and molecular weight distribution on mechanical properties of polymers
Nunes, R. W., Martin, J. R., & Johnson, J. F. (1982) · Polymer Engineering & Science · doi:10.1002/pen.760220402 · Cited by 473
High Strength and High Modulus Electrospun Nanofibers
Yao, J., Bastiaansen, C., & Peijs, T. (2014) · Fibers · doi:10.3390/fib2020158 · Cited by 270
Capaccio, G., Crompton, T. A., & Ward, I. M. (1976) · Journal of Polymer Science: Polymer Physics Edition · doi:10.1002/pol.1976.180140910 · Cited by 234
Self-citationHigh-strength polyethylene fibres from solution and gel spinning
Barham, P. J., & Keller, A. (1985) · Journal of Materials Science · doi:10.1007/bf00556059 · Cited by 219
Metadata
- Authors
- Capaccio, G., & Ward, I. M.
- Affiliations
- University of Leeds (GB)
- ORCID
- Ward, I. M.
- Venue
- Polymer Engineering & Science
- Publisher
- Wiley
- Published
- 1975-03
- Volume
- 15
- Issue
- 3
- Pages
- 219-224
- ISSN
- 0032-3888 (ISSN-L)
- 1548-2634
- OpenAlex
- W2122784560
- Semantic Scholar
- 577d4d0bf5f93fe247802808fa99115eb033ca6b
- Cited by
- 112
- References
- 18
- Citations by year
- 2025: 1 · 2024: 1 · 2023: 1 · 2022: 1 · 2021: 1 · 2020: 4 · 2017: 5 · 2016: 2 · 2015: 2 · 2014: 2 · 2013: 1 · 2012: 2
- FWCI
- 13.07
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Polymer Engineering and Science (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Physical Sciences › Engineering › Mechanical Engineering › Injection Molding Process and Properties
- Keywords
- linear polyethylene, draw ratio, molecular weight, plastic deformation, polymer orientation, stiffness, extensibility, melting point, thermal stability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Ultra‐high‐modulus linear polyethylene through controlled molecular weight and drawing. https://app.cochat.ai/papers/10.1002/pen.760150316
- The paper
- Capaccio, G., & Ward, I. M. (1975). Ultra‐high‐modulus linear polyethylene through controlled molecular weight and drawing. Polymer Engineering & Science. https://doi.org/10.1002/pen.760150316
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.