Ultra‐high‐modulus linear polyethylene through controlled molecular weight and drawing
The DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index.
Abstract
Recent work is presented on the plastic deformation of linear polyethylenes. This work demonstrates the importance of molecular weight and initial morphology in determining the drawing behavior, and shows that by appropriate choice of these two factors a substantial increase in draw ratio and hence stiffness can be achieved over conventionally‐oriented polyethylenes. Under optimum conditions a modulus of approximately 700 Kbar was obtained at a draw ratio of ∼30. These very high modulus materials displayed an extensibility to break of at least 3 percent and a strength of about 4 Kbar. In some cases they also exhibited very high melting points (∼139°C) and exceptionally good thermal stability.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Increasing the degree of orientation increases the Young's modulus.”
In the citing paper
“HDPE elongated in the solid state exhibits a strong dependence of the Young's modulus on molecular orientation, for instance as reported by Capaccio and Ward [34] and Capaccio et al [35].”
Citations
Cites
Longitudinal Acoustical Vibrations of Finite Polymethylene Chains
Schaufele, R. F., & Shimanouchi, T. (1967) · The Journal of Chemical Physics · doi:10.1063/1.1712428 · Cited by 349
Capaccio, G., & Ward, I. M. (1974) · Polymer · doi:10.1016/0032-3861(74)90038-x · Cited by 326
Self-citationThe strength and stiffness of polymers
Frank, F. C. (1970) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1970.0170 · Cited by 319
Calculations of elastic moduli of polymer crystals: I. Polyethylene and nylon 66
Treloar, L. R. G. (1960) · Polymer · doi:10.1016/0032-3861(60)90012-4 · Cited by 218
Properties of Ultra-high Modulus Linear Polyethylenes
CAPACCIO, G., & WARD, I. M. (1973) · Nature Physical Science · doi:10.1038/physci243143a0 · Cited by 174
Self-citationThe cold-drawing of high density polyethylene
Andrews, J. M., & Ward, I. M. (1970) · Journal of Materials Science · doi:10.1007/bf00550003 · Cited by 166
Self-citationCrystal orientation and some properties of solid-state extrudate of linear polyethylene
Imada, K., Yamamoto, T., Shigematsu, K., & Takayanagi, M. (1971) · Journal of Materials Science · doi:10.1007/bf00550308 · Cited by 156
Stress-optical properties of amorphous polyethylene terephthalate fibres
Pinnock, P. R., & Ward, I. M. (1966) · Transactions of the Faraday Society · doi:10.1039/tf9666201308 · Cited by 141
Self-citationDulmage, W. J., & Contois, L. E. (1958) · Journal of Polymer Science · doi:10.1002/pol.1958.1202811703 · Cited by 119
Mechanical properties of ultra‐oriented polyethylene
Weeks, N. E., & Porter, R. S. (1974) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1974.180120401 · Cited by 112
Research works printed but not linked: 7
- L. A.Feldkamp G.Venkateraman andJ. S.King Proc. of Symp. Copenhagen May 1968 Vol. II p.159 LAEA Vienna (1968).
- Sakurada I., 1966, J. Polym. Sci., 15, 75
- A. G.Gibson I. M.Ward B. N.Cole andB.Parsons J. Mat. Sci.(in press).
- J. B.Smith A. J.Manuel andI. M.Ward Polymer(in press).
- J. S.Foot Ph.D. thesis Bristol University (1972).
- G.CapaccioandI. M.Ward Polymer(in press).
- Clark E. S., 1974, ACS Polym. Prepr., 15, 153
Cited by
Strength and toughness of crystalline polymer systems
Galeski, A. (2003) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2003.09.003 · Cited by 614
Influence of molecular weight and molecular weight distribution on mechanical properties of polymers
Nunes, R. W., Martin, J. R., & Johnson, J. F. (1982) · Polymer Engineering & Science · doi:10.1002/pen.760220402 · Cited by 473
High Strength and High Modulus Electrospun Nanofibers
Yao, J., Bastiaansen, C., & Peijs, T. (2014) · Fibers · doi:10.3390/fib2020158 · Cited by 270
Capaccio, G., Crompton, T. A., & Ward, I. M. (1976) · Journal of Polymer Science: Polymer Physics Edition · doi:10.1002/pol.1976.180140910 · Cited by 234
Self-citationHigh-strength polyethylene fibres from solution and gel spinning
Barham, P. J., & Keller, A. (1985) · Journal of Materials Science · doi:10.1007/bf00556059 · Cited by 219
Ultrahigh-strength polyethylene filaments by solution spinning and hot drawing
Smith, P., Lemstra, P. J., Kalb, B., & Pennings, A. J. (1979) · Polymer Bulletin · doi:10.1007/bf00256272 · Cited by 218
Tensile creep and recovery in ultra-high modulus linear polyethylenes
Wilding, M. A., & Ward, I. M. (1978) · Polymer · doi:10.1016/0032-3861(78)90208-2 · Cited by 160
Self-citationGogolewski, S., & Pennings, A. J. (1983) · Journal of Applied Polymer Science · doi:10.1002/app.1983.070280312 · Cited by 113
Perkins, W. G., Capiati, N. J., & Porter, R. S. (1976) · Polymer Engineering and Science · doi:10.1002/pen.760160313 · Cited by 126
Structure-induced enhancement of thermal conductivities in electrospun polymer nanofibers
Zhong, Z., Wingert, M. C., Strzalka, J. W., Wang, H., Sun, T., Wang, J., Chen, R., & Jiang, Z. (2014) · Nanoscale · doi:10.1039/c4nr00547c · Cited by 113
Raman spectroscopy of stressed high modulus poly(p-phenylene benzobisthiazole) fibres
Day, R., Robinson, I. M., Zakikhani, M., & Young, R. J. (1987) · Polymer · doi:10.1016/0032-3861(87)90287-4 · Cited by 105
The preparation, structure and properties of ultra-high modulus flexible polymers
Ward, I. M. (1985) · Advances in polymer science · doi:10.1007/3-540-15481-7_7 · Cited by 95
Self-citationThe preparation of ultra‐high modulus polypropylene films and fibres
Cansfield, D. L. M., Capaccio, G., & Ward, I. M. (1976) · Polymer Engineering and Science · doi:10.1002/pen.760161102 · Cited by 87
Self-citationNovel composites by hot compaction of fibers
Ward, I. M., & Hine, P. J. (1997) · Polymer Engineering and Science · doi:10.1002/pen.11830 · Cited by 84
Self-citationSolid-state deformation of polyethylene and nylon and its effects on their structure and morphology
Perkins, W. G., & Porter, R. S. (1977) · Journal of Materials Science · doi:10.1007/bf00553923 · Cited by 77
Sahputra, I. H., & Echtermeyer, A. T. (2013) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/0965-0393/21/6/065016 · Cited by 76
A study of the gas barrier properties of highly oriented polyethylene
Holden, P. S., Orchard, G. A. J., & Ward, I. M. (1985) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1985.180230408 · Cited by 76
Self-citationThe plastic deformation behaviour of linear polyethylene and polyoxymethylene
Coates, P. D., & Ward, I. M. (1978) · Journal of Materials Science · doi:10.1007/bf00552903 · Cited by 75
Self-citationA review of techniques for processing ultra‐high modulus polymers
Bigg, D. M. (1976) · Polymer Engineering and Science · doi:10.1002/pen.760161103 · Cited by 70
The drawing behavior of polyvinylalcohol fibers
Schellekens, R., & Bastiaansen, C. W. M. (1991) · Journal of Applied Polymer Science · doi:10.1002/app.1991.070431221 · Cited by 67
Phase equilibria of rod‐like molecules in an extensional flow field
Marrucci, G., & CIFERRI, A. (1977) · Journal of Polymer Science Polymer Letters Edition · doi:10.1002/pol.1977.130151101 · Cited by 67
Wu, W., & Black, W. B. (1979) · Polymer Engineering and Science · doi:10.1002/pen.760191606 · Cited by 62
Predictions of limiting mechanical performance for anisotropic crystalline polymers
McCullough, R. L., Wu, C., Seferis, J. C., & Lindenmeyer, P. H. (1976) · Polymer Engineering and Science · doi:10.1002/pen.760160517 · Cited by 60
Hydrostatically extruded HAPEX™
Wang, M., Ladizesky, N. H., Tanner, K. E., Ward, I. M., & Bonfield, W. (2000) · Journal of Materials Science · doi:10.1023/a:1004731315328 · Cited by 59
Self-citationA Review of the Mechanical and Physical Properties of Polyethylene Fibers
Roiron, C., Lainé, É., Grandidier, J.-C., Garois, N., & Vix‐Guterl, C. (2021) · Textiles · doi:10.3390/textiles1010006 · Cited by 58
Ultra‐high‐modulus fibers from solution spinning
CIFERRI, A. (1975) · Polymer Engineering and Science · doi:10.1002/pen.760150311 · Cited by 58
High‐modulus polydiacetylene single‐crystal fibers
Galiotis, C., Read, R. T., Yeung, P. H. J., Young, R. J., Chalmers, I. F., & Bloor, D. (1984) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1984.180220903 · Cited by 56
Ultra-high modulus polyethylene. 1 Effect of drawing temperature
Jarecki, L., & Meier, D. J. (1979) · Polymer · doi:10.1016/0032-3861(79)90297-0 · Cited by 52
1.5 High Performance Polyethylene Fibers
Peijs, T. (2017) · Elsevier eBooks · doi:10.1016/b978-0-12-803581-8.09876-3 · Cited by 52
The morphology of ultradrawn polyethylene. I. Nitric acid etching plus gel permeation chromatography
Weeks, N. E., Mori, S., & Porter, R. S. (1975) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1975.180131013 · Cited by 49
High performance polyethylene fibers
Deitzel, J. M., McDaniel, P. B., & Gillespie, J. W. (2016) · Elsevier eBooks · doi:10.1016/b978-0-08-100550-7.00007-3 · Cited by 49
Study on the drawing behavior of poly( L ‐lactide) to obtain high‐strength fibers
Postema, A. R., & Pennings, A. J. (1989) · Journal of Applied Polymer Science · doi:10.1002/app.1989.070370824 · Cited by 47
Production and properties of fibers spun from nylon 6/lithium chloride mixtures
Richardson, A. P., & Ward, I. M. (1981) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1981.180191006 · Cited by 47
Self-citationGaliotis, C., & Young, R. J. (1983) · Polymer · doi:10.1016/0032-3861(83)90155-6 · Cited by 46
Increasing the elastic modulus of polyamides
Acierno, D., Mantia, F. P. L., Polizzotti, G., Alfonso, G. C., & CIFERRI, A. (1977) · Journal of Polymer Science Polymer Letters Edition · doi:10.1002/pol.1977.130150601 · Cited by 45
Nakae, M., Uehara, H., Kanamoto, T., Ohama, T., & Porter, R. S. (1999) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/(sici)1099-0488(19990801)37:15<1921::aid-polb16>3.0.co;2-m · Cited by 41
Ultrahigh modulus polyethylene. II. Effect of drawing temperature on void formation and modulus
Jarecki, L., & Meier, D. J. (1979) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1979.180170913 · Cited by 40
Anisotropic Elastic Modulus of Oriented Regioregular Poly(3-hexylthiophene) Films
Awartani, O., Zhao, B., Currie, T., Kline, R. J., Zikry, M. A., & O’Connor, B. T. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b02680 · Cited by 38
Kristiansen, P. M., Tervoort, T. A., & Smith, P. (2003) · Polymer · doi:10.1016/s0032-3861(03)00538-x · Cited by 38
Bastiaansen, C. W. M. (1990) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1990.090280905 · Cited by 38
Tensile properties of biaxially drawn polyethylene
Gerrits, N. J. A., Young, R. J., & Lemstra, P. J. (1990) · Polymer · doi:10.1016/0032-3861(90)90111-b · Cited by 37
Dessain, B., Moulaert, O., Keunings, R., & Bunsell, A. R. (1992) · Journal of Materials Science · doi:10.1007/bf00541588 · Cited by 36
Capaccio, G., Ward, I. M., Wilding, M., & Longman, G. W. (1978) · Journal of Macromolecular Science Part B · doi:10.1080/00222347808212262 · Cited by 32
Self-citationMackley, M. R. (2010) · Rheologica Acta · doi:10.1007/s00397-010-0435-z · Cited by 31
Du, B., Zhang, J., Zhang, Q., Yang, D., He, T., & Tsui, O. K. C. (2000) · Macromolecules · doi:10.1021/ma000943g · Cited by 31
6.7 Electrospun Polymer Nanofibers and Their Composites
Peijs, T. (2017) · Elsevier eBooks · doi:10.1016/b978-0-12-803581-8.10025-6 · Cited by 29
High Performance Polyethylene Fibers
Peijs, T., Jacobs, M., & Lemstra, P. J. (2000) · Elsevier eBooks · doi:10.1016/b0-08-042993-9/00047-4 · Cited by 27
Analysis and modelling of the die drawing of polymers
Kukureka, S. N., Craggs, G. M. J., & Ward, I. M. (1992) · Journal of Materials Science · doi:10.1007/bf01116040 · Cited by 25
Self-citationGreco, R., Mucciariello, G., Ragosta, G., & Martuscelli, E. (1981) · Journal of Materials Science · doi:10.1007/bf00542745 · Cited by 25
Experimental measurement of polyethylene chain modulus by scanning force microscopy
Du, B., Liu, J.-P., Zhang, Q., & He, T. (2001) · Polymer · doi:10.1016/s0032-3861(00)00910-1 · Cited by 25
The interpretation of dynamic mechanical behavior in ultra high modulus polymers
Gibson, A. G., Davies, G. R., & Ward, I. M. (1980) · Polymer Engineering and Science · doi:10.1002/pen.760201405 · Cited by 23
Self-citationWang, M. H., Ruan, W., Huang, Y., Ye, L., Rong, M. Z., & Zhang, M. Q. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm16097h · Cited by 22
Swell drawing: A new method of manufacturing high performance polyethylene structures
Mackley, M. R., & Solbai, S. (1987) · Polymer · doi:10.1016/0032-3861(87)90252-7 · Cited by 22
Sherman, E. S., Porter, R. S., & Thomas, E. L. (1982) · Polymer · doi:10.1016/0032-3861(82)90410-4 · Cited by 22
Abdallah, A. B., Gamaoun, F., Kallel, A., & Tcharkhtchi, A. (2020) · Journal of Applied Polymer Science · doi:10.1002/app.49761 · Cited by 19
Production and properties of high-modulus and high-strength polyethylene fibres
Ward, I. M., & Lemstra, P. J. (2009) · Elsevier eBooks · doi:10.1533/9781845696504.2.352 · Cited by 15
Self-citationYe, C., Wang, C., Wang, J., Wiener, C. G., Xia, X., Cheng, S. Z. D., Li, R., Yager, K. G., Fukuto, M., & Vogt, B. D. (2017) · Soft Matter · doi:10.1039/c7sm01366c · Cited by 14
Verstärkungsfasern für Verbundwerkstoffe
Diefendorf, R. J., Fitzer, E., & Heym, M. (1976) · Chemie Ingenieur Technik · doi:10.1002/cite.330480907 · Cited by 14
Anisotropie Elastic Behavior of Crystalline Polymers
McCullough, R. L. (1977) · Treatise on materials science and technology · doi:10.1016/s0161-9160(13)70094-2 · Cited by 13
Matsuo, M., Sato, R., Yanagida, N., & Shimizu, Y. (1992) · Polymer · doi:10.1016/0032-3861(92)91060-f · Cited by 13
Ultra High Modulus Fibers from Solution and Melt Spinning
CIFERRI, A. (1978) · International Journal of Polymeric Materials · doi:10.1080/00914037808077905 · Cited by 13
Material Characterization of Heat Shrinkable Film
Kalkan-Sevinc, Z. S., & Strobel, C. T. (2015) · Journal of Testing and Evaluation · doi:10.1520/jte20130112 · Cited by 12
Zachariades, A. E., Kanamoto, T., & Porter, R. S. (1980) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1980.180180316 · Cited by 12
Properties of polyethylene-propylene blends: Part 3 Mechanical characterization of ultradrawn fibres
Tang, M. R., Greco, R., Ragosta, G., & Cimmino, S. (1983) · Journal of Materials Science · doi:10.1007/bf00551971 · Cited by 12
The role of crystallinity and morphology in the preparation of ultra‐highly oriented polyethylene
Capaccio, G., Crompton, T. A., & Ward, I. M. (1978) · Polymer Engineering and Science · doi:10.1002/pen.760180617 · Cited by 12
Self-citationCrystallisation and Recrystallisation
Krevelen, D. W. V., & Nijenhuis, K. T. (2009) · Elsevier eBooks · doi:10.1016/b978-0-08-054819-7.00019-4 · Cited by 11
Mimaroglu, A., Yenihayat, Ö. F., & Çelebi, A. (1995) · Materials & Design (1980-2015) · doi:10.1016/0261-3069(95)00037-2 · Cited by 11
Preparation of high performance PET fiber by solution spinning technique
Wu, G., & Cuculo, J. A. (1995) · Journal of Applied Polymer Science · doi:10.1002/app.1995.070560711 · Cited by 11
Young, R. J. (1989) · Elsevier eBooks · doi:10.1016/b978-0-08-096701-1.00052-5 · Cited by 11
Pilato, L. A., & Michno, M. J. (1994) · Springer eBooks · doi:10.1007/978-3-662-35356-1_3 · Cited by 10
Shear strength of highly drawn linear polyethylene sheets
Ladizesky, N. H., & Ward, I. M. (1988) · Journal of Materials Science · doi:10.1007/bf01174037 · Cited by 10
Self-citationPreparation and properties of high modulus–tensile strength polymeric materials
Peiffer, D. G. (1980) · Polymer Engineering and Science · doi:10.1002/pen.760200209 · Cited by 10
Biaxial orientation of polymers by solid state extrusion through convergent-divergent dies
Mascia, L., & Zhao, J. (1991) · Rheologica Acta · doi:10.1007/bf00404196 · Cited by 9
Zeeshan, Z., Mohamed, A., Khan, I., Khan, M. S., Yassen, M. F., & Ullah, S. (2023) · Science Progress · doi:10.1177/00368504231172617 · Cited by 8
The elastic modulus of poly(ethylene terephthalate-co-p-oxybenzoate)
Carfagna, C., Amendola, E., Nobile, M. R., & Nicolais, L. (1988) · Journal of Materials Science Letters · doi:10.1007/bf01730294 · Cited by 8
The structure and properties of ultra-high modulus polymers
Ward, I. M. (1979) · Polymer Science U.S.S.R. · doi:10.1016/0032-3950(79)90385-x · Cited by 8
Self-citationCRYSTALLIZATION AND RECRYSTALLIZATION
Krevelen, D. W. V. (1997) · Elsevier eBooks · doi:10.1016/b978-0-444-82877-4.50026-3 · Cited by 8
Fouda, I. M., & Shabana, H. M. (1999) · Polymer International · doi:10.1002/(sici)1097-0126(199903)48:3<181::aid-pi135>3.0.co;2-v · Cited by 8
Eriksson, M., Goossens, H., & Peijs, T. (2020) · Fibers · doi:10.3390/fib8110070 · Cited by 7
Zur übermolekularen Struktur hochmoduliger scherkristallisierter Polyethylen‐Fäden
Walenta, E., Hofmann, D., Zenke, D., & Geiß, D. (1989) · Acta Polymerica · doi:10.1002/actp.1989.010400504 · Cited by 7
New horizons in advanced oriented fiber
Tam, T., Boone, M. B., & Weedon, G. C. (1988) · Polymer Engineering and Science · doi:10.1002/pen.760281308 · Cited by 7
Young, R. J. (1987) · Springer eBooks · doi:10.1007/978-94-009-3427-6_1 · Cited by 6
Melting behaviour of oriented isotactic polypropylene
Yadav, Y. S., & Jain, P. (1987) · Thermochimica Acta · doi:10.1016/0040-6031(87)88105-4 · Cited by 6
Transverse orientation dies for solid‐state extrusion of polymers. Part I: Process mechanics
Mascia, L., & Zhao, J. (1991) · Polymer Engineering and Science · doi:10.1002/pen.760310908 · Cited by 5
Mechanical and Structural Properties of Polydiacetylenes
Young, R. J. (1985) · Springer eBooks · doi:10.1007/978-94-017-2713-6_25 · Cited by 5
Fibre formation in the hydrostatic extrusion of linear polyethylene — sodium lignosulphonate blends
Kubát, J., Månson, J. A., & Rigdahl, M. (1982) · Journal of Materials Science · doi:10.1007/bf00540390 · Cited by 5
Nonlinear viscoelastic response of a thermodynamically metastable polymer melt
Pandey, A. (2011) · Loughborough University Research Repository (Loughborough University) · Cited by 5
Liu, L. B., Murakami, N., Sumita, M., & Miyasaka, K. (1989) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1989.090271204 · Cited by 4
Preparation of highly doubly oriented polymers
Narayanan, M. J. S., & Magill, J. H. (1986) · Journal of Materials Science Letters · doi:10.1007/bf01748073 · Cited by 4
Rearranjo estrutural de PET durante compressão plana
Denardin, E. L. G. (2004) · Americanae (AECID Library) · Cited by 4
11 Introduction to Polymer Processing
Nadkami, V. M. (2017) · CRC Press eBooks · doi:10.1201/9781315140322-12 · Cited by 3
Mechanically induced polyamorphism in a one-dimensional coordination polymer
Nishiguchi, T., Ohara, Y., Kadota, K., Zheng, X., Noro, S., & Horike, S. (2024) · Chemical Science · doi:10.1039/d4sc07058e · Cited by 3
Introduction to Polymer Processing
Nadkami, V. M. (2017) · CRC Press eBooks · doi:10.1201/9781315140322-11 · Cited by 3
Drawing of high density polyethylene tube: Effect of different cooling conditions
Ulas, I. (1999) · Polymer Engineering and Science · doi:10.1002/pen.11474 · Cited by 3
Inoue, N. (1985) · Springer eBooks · doi:10.1007/978-94-009-4954-6_14 · Cited by 3
Deformation behavior of a polyvinyl chloride (PVC) tube by mandrel drawing
Ulas, I. (1999) · Polymer Engineering and Science · doi:10.1002/pen.11565 · Cited by 3
Polymer microstructure and deformation processes
Duckett, R. A. (1983) · International Metals Reviews · doi:10.1179/imtr.1983.28.1.158 · Cited by 3
Berger, W., Gräfe, F., & Kammer, H. W. (1984) · Acta Polymerica · doi:10.1002/actp.1984.010350706 · Cited by 3
Ultra-High Strength Polyethylene Fiber and its Applications
Wincklhofer, R. C., & Rothwell, R. A. (1986) · MTS/IEEE OCEANS Conference (OCEANS) · doi:10.1109/oceans.1986.1160532 · Cited by 2
Kinloch, A. J., & Young, R. J. (1995) · Springer eBooks · doi:10.1007/978-94-017-1594-2_9 · Cited by 2
Metadata
- Authors
- Capaccio, G., & Ward, I. M.
- Affiliations
- University of Leeds (GB)
- ORCID
- Ward, I. M.
- Venue
- Polymer Engineering & Science
- Publisher
- Wiley
- Published
- 1975-03
- Volume
- 15
- Issue
- 3
- Pages
- 219-224
- ISSN
- 0032-3888 (ISSN-L)
- 1548-2634
- OpenAlex
- W2122784560
- Semantic Scholar
- 577d4d0bf5f93fe247802808fa99115eb033ca6b
- Cited by
- 112
- References
- 18
- Citations by year
- 2025: 1 · 2024: 1 · 2023: 1 · 2022: 1 · 2021: 1 · 2020: 4 · 2017: 5 · 2016: 2 · 2015: 2 · 2014: 2 · 2013: 1 · 2012: 2
- FWCI
- 13.07
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Polymer Engineering and Science (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Physical Sciences › Engineering › Mechanical Engineering › Injection Molding Process and Properties
- Keywords
- linear polyethylene, draw ratio, molecular weight, plastic deformation, polymer orientation, stiffness, extensibility, melting point, thermal stability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.