Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes
The DOI matches its Crossref record; 26 of the 26 references it cites were found in a registry or an index.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The most important characteristics of drilled-hole quality are surface roughness (SR) and the deviation of the hole size (HS) from its nominal diameter [2].”
From Optimization and Modeling of Process Parameters in Multi-Hole Simultaneous Drilling Using Taguchi Method and Fuzzy Logic Approach (2020) · cites this paper as [2]
Citations
Cites
Taguchi Techniques for Quality Engineering
Bement, T. R. (1989) · Technometrics · doi:10.1080/00401706.1989.10488519 · Cited by 2,718
Quality Engineering Using Robust Design
Kapur, K. C. (1990) · Journal of Quality Technology · doi:10.1080/00224065.1990.11979247 · Cited by 2,125
Introduction to Quality Engineering
(2008) · WORLD SCIENTIFIC eBooks · doi:10.1142/9789812778697_0001 · Cited by 1,511
Design optimization of cutting parameters for turning operations based on the Taguchi method
Yang, W. H., & Tarng, Y. S. (1998) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(98)00079-x · Cited by 1,302 · cited 1×
“To solve this problem, the Taguchi method uses a special design of orthogonal arrays to study the entire parameter space with only a small number of experiments [ 15 ].”
MethodQuality Engineering using Design of Experiments
Phadke, M. S. (1989) · Quality Control, Robust Design, and the Taguchi Method · doi:10.1007/978-1-4684-1472-1_3 · Cited by 585
Taguchi Techniques for Quality Engineering
Ziegel, E. R. (1997) · Technometrics · doi:10.1080/00401706.1997.10485460 · Cited by 533
Tsao, C. C., & Hocheng, H. (2004) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2004.02.019 · Cited by 368
Quality Engineering Using Robust Design
Menten, T. (1991) · Technometrics · doi:10.1080/00401706.1991.10484810 · Cited by 296
Experimental analysis and optimisation of tool wear in dry machining of aluminium alloys
Nouari, M., List, G., Girot, F., & Coupard, D. (2003) · Wear · doi:10.1016/s0043-1648(03)00105-4 · Cited by 284
Minimal lubrication machining of aluminium alloys
Kelly, J. F., & Cotterell, M. G. (2002) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(01)01126-8 · Cited by 242
Research works printed but not linked: 2
- Lou MS, Chen JC, Li CM (1998) Surface roughness prediction technique for CNC end-milling. J Ind Technol 15:1–6
- Yang JL, Chen JC (2001) A systematic approach for identifying optimum surface roughness performance in end-milling operations. J Ind Technol 17:1–8
Cited by
A review: drilling performance and hole quality of aluminium alloys for aerospace applications
Aamir, M., Giasin, K., Tolouei-Rad, M., & Vafadar, A. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.09.003 · Cited by 286
“↑ Speed [53,70–73,75] [58,96] [72,73,78,96] [24,52,97] [53,70,71,74,75] – ↑ Feed [24,53,58,70–73,75] [52] [72,73,96,97] [52] [53,70,71,75] [53] ↑ Point angle [75] [52,58,72] [78] [52,58,72] [75] – ↑ Helix angle [52] [58] – ↑ Drill diameter [73] – [73]”
BackgroundKrishnamoorthy, A., Boopathy, S. R., Palanikumar, K., & Davim, J. P. (2012) · Measurement · doi:10.1016/j.measurement.2012.01.008 · Cited by 181
Chen, W., Nguyen, M.-H., Chiu, W., et al. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-7683-0 · Cited by 150
Optimization of Binder Jetting Using Taguchi Method
Shrestha, S., & Manogharan, G. P. (2017) · JOM · doi:10.1007/s11837-016-2231-4 · Cited by 145
Günay, M., & Yücel, E. (2012) · Measurement · doi:10.1016/j.measurement.2012.10.013 · Cited by 131
Gök, A. (2015) · Measurement · doi:10.1016/j.measurement.2015.03.037 · Cited by 130
Adin, M. Ş., & Adın, H. (2024) · Polymers · doi:10.3390/polym16233329 · Cited by 127
Çıçek, A., Kıvak, T., & Ekici, E. (2013) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-013-0783-5 · Cited by 121
“Drill geometry, the drill and workpiece materials are the most important factors which influence the drill performance and the hole quality (Kurt et al. 2009).”
BackgroundOptimization of wire electrical discharge machining process parameters for cutting tungsten
Yang, R. T., Tzeng, C., Yang, Y. K., et al. (2011) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3576-z · Cited by 117
Kıvak, T., Samtaş, G., & Çiçek, A. (2012) · Measurement · doi:10.1016/j.measurement.2012.02.022 · Cited by 116
“[17] employed Taguchi methods in the optimisation of cutting parameters for surface finish, and holediameter accuracy in a dry drilling process.”
MethodGiasin, K., Hodzic, A., Phadnis, V. A., & Ayvar-Soberanis, S. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-8563-y · Cited by 125
Multi-criteria decision making in the selection of machining parameters for Inconel 718
Ramanathan, T., & Senthilkumaar, J. S. (2013) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-013-0215-7 · Cited by 92
“Taguchi method has been widely utilized in engineering analysis and consists of experiment plans, with the objective of acquiring data in a controlled manner in order to obtain information on the behavior of a given process [12].”
MethodGök, A., Göloğlu, C., & Demirci, H. İ. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5075-x · Cited by 87
“[8] have worked on the optimization of cutting parameters for the finish surface and the accuracy of the hole diameter during dry drilling.”
BackgroundAamir, M., Tu, S., Tolouei-Rad, M., Giasin, K., & Vafadar, A. (2020) · Materials · doi:10.3390/ma13030680 · Cited by 86
“Then, regression analysis and ANOVA were applied to confirm the accuracy of the model and the significance of process parameters.”
BackgroundMethodInfluentialAn experimental study into the effect of micro-textures on the performance of cutting tool
Durairaj, S., Guo, J., Aramcharoen, A., et al. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-2309-y · Cited by 84
Çıçek, A., Kıvak, T., & Samtaş, G. (2012) · Strojniški vestnik – Journal of Mechanical Engineering · doi:10.5545/sv-jme.2011.167 · Cited by 83
“[21] employed the Taguchi method in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes.”
MethodSurgical Drill Bit Design and Thermomechanical Damage in Bone Drilling: A Review
Akhbar, M. F. A., & Sulong, A. W. (2020) · Annals of Biomedical Engineering · doi:10.1007/s10439-020-02600-2 · Cited by 78
Machining aerospace aluminium alloy with cryo-treated and untreated HSS cutting tools
Adin, M. Ş. (2023) · Advances in Materials and Processing Technologies · doi:10.1080/2374068x.2023.2273035 · Cited by 111
“In workpiece drilling operations, it is very crucial to choose the most suitable cutting parameters and cutting tool to attain high hole quality and high cutting tool performance [33–36].”
Zerti, O., Yallese, M. A., Khettabi, R., Chaoui, K., & Mabrouki, T. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-9162-7 · Cited by 74
Optimization in thermal friction drilling for SUS 304 stainless steel
Ku, W.-L., Hung, C.-L., Lee, S.-M., et al. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-010-2899-5 · Cited by 69
Al-Tameemi, H. A., Al-Dulaimi, T., Awe, M. O., Sharma, S. K., Pimenov, D. Y., Köklü, U., & Giasin, K. (2021) · Materials · doi:10.3390/ma14071783 · Cited by 71
Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method
Ramanathan, T., Senthilkumaar, J. S., Selvarani, P., & Ramesh, S. (2012) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406212466193 · Cited by 64
Machinability of Al2024, Al6061, and Al5083 alloys using multi-hole simultaneous drilling approach
Aamir, M., Tolouei‐Rad, M., Giasin, K., & Vafadar, A. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.07.078 · Cited by 76
“operation, despite the development of the modern cutting process in manufacturing industries [11].”
BackgroundMeral, G., Sarıkaya, M., Mia, M., et al. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-3061-z · Cited by 63
Wu, J. S., Cheng, J., Gao, C., et al. (2019) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2019.105263 · Cited by 60
Giasin, K., Ayvar-Soberanis, S., & Hodzic, A. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.10.049 · Cited by 59
Adin, M. Ş., İşcan, B., & Baday, Ş. (2023) · Materials Today Communications · doi:10.1016/j.mtcomm.2023.107301 · Cited by 57
Adin, M. Ş. (2023) · European Mechanical Science · doi:10.26701/ems.1270937 · Cited by 56
Tzeng, C., Yang, Y., Lin, Y., et al. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-3933-6 · Cited by 55
“Although the Taguchi method has been used quite successfully in several industrial applications as in optimizing manufacturing processes, designing electrical, and mechanical components [16–20].”
MethodTzeng, C.-J., Yang, Y.-K., Hsieh, M.-H., et al. (2011) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1243/09544054jem2021 · Cited by 54
Srinivasan, K., Muthu, S., Devadasan, S. R., & Sugumaran, C. (2016) · Production Planning & Control · doi:10.1080/09537287.2016.1143130 · Cited by 61
“…per million opportunities (dPMo) =[number of defects/(number of units × number of opportunities)]×106 =[7/(50 × 4)] × 1,000,000 =35,000 Kulkarani, and Ramachandra 2007; Kurt, Bagci, and Kaynak 2009; Kaushik et al. 2012). using this software, the response table and the main effect plots for S/n…”
BackgroundMethodGök, K., Gök, A., & Kişioğlu, Y. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6327-0 · Cited by 53
“[40] worked on the optimization of drilling parameters for the finish surface process during dry drilling using the Taguchi method.”
MethodSakthivel Murugan, R., & Vinodh, S. (2020) · Rapid Prototyping Journal · doi:10.1108/rpj-10-2019-0269 · Cited by 56
Design and experimental study of an end effector for robotic drilling
Liang, J., & Bi, S. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-009-2494-9 · Cited by 53
Zhang, G., Li, J., Chen, Y., et al. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-6232-6 · Cited by 52
“[20] utilized Taguchi methods to optimize surface finish and hole diameter accuracy in the dry drilling of Al 2024 alloy.”
MethodOn near-dry wire ECDM of Al6063/SiC/10p MMC
Shamim, F. A., Dvivedi, A., & Kumar, P. (2020) · Materials and Manufacturing Processes · doi:10.1080/10426914.2020.1802044 · Cited by 51
TASKESEN, A., & KUTUKDE, K. (2013) · Transactions of Nonferrous Metals Society of China · doi:10.1016/s1003-6326(13)62764-8 · Cited by 47
“The measurement of the hole size is of significant importance for a variety of applications [31].”
BackgroundYücel, E., & Günay, M. (2012) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406212471755 · Cited by 42
“Steps of Taguchi optimization method.(19)”
BackgroundInfluentialVilleta, M., de Agustina, B., de Pipaón, J. M. S., et al. (2011) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3685-8 · Cited by 40
Tansel, I., Gúlmez, S., Demetgül, M., et al. (2010) · Expert Systems with Applications · doi:10.1016/j.eswa.2010.09.170 · Cited by 38
“The S/N ratios were calculated (Kurt et al., 2009; Oktem et al., 2007; Onders et al., 1996; Tsao & Hocheng, 2004; Tzeng & Chiu, 2003) and listed in Table 11.”
MethodKarabulut, Y., & Kaynak, Y. (2020) · Procedia CIRP · doi:10.1016/j.procir.2020.02.110 · Cited by 38
Self-citationTran, Q.-P., Nguyen, V.-N., & Huang, S. (2020) · Applied Sciences · doi:10.3390/app10207207 · Cited by 38
Kannan, T. D. B., Kannan, G. R., Kumar, B. S., et al. (2014) · Procedia Materials Science · doi:10.1016/j.mspro.2014.07.433 · Cited by 37
Kumar, B. S., & Baskar, N. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4275-0 · Cited by 38
“Surface roughness plays an important role in product quality and manufacturing process planning [21].”
BackgroundAamir, M., Tolouei‐Rad, M., Giasin, K., & Vafadar, A. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-06151-7 · Cited by 37
“The drilling process is used in many applications such as the aerospace, aircraft, and automotive industries [2].”
MethodAbdallah, A. (2014) · IOSR Journal of Engineering · doi:10.9790/3021-041010110 · Cited by 35
Effects of cutting parameters and tool-path strategies on tool acceleration in ball-end milling
Gök, A., Gök, K., Bilgin, M. B., & Alkan, M. (2017) · Materiali in tehnologije · doi:10.17222/mit.2017.039 · Cited by 35
A Study on Temperature Rise, Tool Wear, and Surface Roughness During Drilling of Al–5%SiC Composite
Thirukkumaran, K., Menaka, M., Mukhopadhyay, C. K., et al. (2020) · Arabian Journal for Science and Engineering · doi:10.1007/s13369-020-04427-4 · Cited by 32
Process parameters optimization for eco-friendly high strength sandcrete block using Taguchi method
Ikeagwuani, C. C., Nwonu, D. C., Ugwu, C. K., et al. (2020) · Heliyon · doi:10.1016/j.heliyon.2020.e04276 · Cited by 31
“[39] applied the Taguchi method for optimizing the process parameters in dry drilling processes.”
MethodNeseli, S. (2014) · Advances in Mechanical Engineering · doi:10.1155/2014/925382 · Cited by 30
ÖZLÜ, B. (2022) · Surface Review and Letters · doi:10.1142/s0218625x22501037 · Cited by 28
Aamir, M., Tolouei‐Rad, M., Vafadar, A., Raja, M. N. A., & Giasin, K. (2020) · Applied Sciences · doi:10.3390/app10238633 · Cited by 31
“The surface roughness has a key role in the evaluation of machining performance of a workpiece [36].”
BackgroundTaguchi Method Implementation in Taper Motion Wire EDM Process Optimization
Martowibowo, S. Y., & Wahyudi, A. (2012) · Journal of The Institution of Engineers (India) Series C · doi:10.1007/s40032-012-0043-z · Cited by 28
Chinnathambi, D., & Alwarsamy, T. (2012) · Procedia Engineering · doi:10.1016/j.proeng.2012.06.241 · Cited by 28
Kumar, B. S., Baskar, N., & Rajaguru, K. (2019) · Materials Today Proceedings · doi:10.1016/j.matpr.2019.08.160 · Cited by 32
Han, C., Luo, M., & Zhang, D. (2020) · Applied Soft Computing · doi:10.1016/j.asoc.2020.106489 · Cited by 27
Somasundaram, G., Boopathy, S. R., & Palanikumar, K. (2011) · Journal of Composite Materials · doi:10.1177/0021998311410493 · Cited by 26
“Drill performance and hole quality are mainly dependent on the cutting parameters and tools.(11) Hence, to reduce the wear of tool and cost of making flutes of the drill, a fluteless friction drill is studied.”
BackgroundShunmugesh, K., & Panneerselvam, K. (2017) · Pigment & Resin Technology · doi:10.1108/prt-03-2016-0029 · Cited by 25
Aamir, M., Tu, S., Giasin, K., & Tolouei‐Rad, M. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.02.026 · Cited by 26
“026 parameters with a significant impact on the quality characteristic [32].”
BackgroundAamir, M., Tolouei‐Rad, M., Giasin, K., Vafadar, A., Köklü, U., & Keeble, W. (2021) · Applied Sciences · doi:10.3390/app11094285 · Cited by 29
“[10], it was concluded that the diametric error was affected more by the feed rate, while the cutting speed had a high impact on surface roughness.”
BackgroundEffect of bolt size on the bearing strength of bolt-connected orthotropic CFRP laminate
Liu, K., Liu, Y., Sabbrojjaman, M., et al. (2022) · Polymer Testing · doi:10.1016/j.polymertesting.2022.107894 · Cited by 25
Kalidass, S., & Palanisamy, P. (2014) · Arabian Journal for Science and Engineering · doi:10.1007/s13369-014-1346-6 · Cited by 25
Chatterjee, S., Abhishek, K., Mahapatra, S. S., et al. (2014) · Procedia Engineering · doi:10.1016/j.proeng.2014.12.227 · Cited by 23
“[4] have pointed out that work piece, drill geometry and the drill bit material are important parameters that influence circularity of the drilled hole.”
BackgroundExperimental investigation and analysis of drilling parameters of metal matrix (Ti/TiB) composites
Ramkumar, T., Selvakumar, M., Mohanraj, M. P., et al. (2018) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-018-1507-8 · Cited by 23
Adalarasan, R., & Santhanakumar, M. (2014) · Journal of The Institution of Engineers (India) Series C · doi:10.1007/s40032-014-0124-2 · Cited by 22
Delik delme prosesi: bir araştırma
Bayraktar, Ş., Sıyambaş, Y., & Turgut, Y. (2017) · Sakarya University Journal of Science · doi:10.16984/saufenbilder.296833 · Cited by 21
Shi, H., Giasin, K., Barouni, A. K., & Zhang, Z. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-13009-9 · Cited by 21
Tiryaki, S., Hamzaçebi, Ç., & Malkoçoğlu, A. (2015) · European Journal of Wood and Wood Products · doi:10.1007/s00107-015-0917-x · Cited by 21
“S/N ratio is defined as the desired signal ratio for the undesired random noise value and shows the quality characteristics of the experimental data (Kurt et al. 2009).”
BackgroundEffect of cooling methods on hole quality in drilling of aluminium 6061-6T
Islam, M. N., & Boswell, B. (2016) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/114/1/012022 · Cited by 20
Aamir, M., Tolouei‐Rad, M., & Giasin, K. (2021) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-021-07082-7 · Cited by 19
Bearing strength and progressive failure analysis of the punched hole of CFRP under tensile loading
Abdullah, M. S., Abdullah, A. B., Hassan, M. H., et al. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-2091-x · Cited by 18
Experimental Assessment of Hole Quality and Tool Condition in the Machining of an Aerospace Alloy
Aamir, M., Sharif, A., Zahir, M. Z., Giasin, K., & Tolouei‐Rad, M. (2023) · Machines · doi:10.3390/machines11070726 · Cited by 19
Ranganath, M. S., Vipin, V., & Mishra, R. S. (2014) · International Journal of Advance Research and Innovation · doi:10.51976/ijari.211426 · Cited by 17
Optimization Drilling Parameters of Aluminum Alloy Based on Taguchi Method
Haleel, A. J. (2019) · Al-Khwarizmi Engineering Journal · doi:10.22153/kej.2018.12.001 · Cited by 17
“(2009) used the “Taguchi” approach to optimize the cutting parameters of the hole diameter accuracy and surface finish in dry drilling operations [2].”
MethodExperimental study of inverted drilling Al-7075 alloy
Kao, J., Hsu, C.-Y., & Tsao, C. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-03416-8 · Cited by 17
Modeling and Optimization of Machining Processes
Rao, R. V. (2010) · Springer series in advanced manufacturing · doi:10.1007/978-0-85729-015-1_2 · Cited by 21
Optimization of Drilling Process Parameters Via Taguchi, TOPSIS and RSA Techniques
Shunmugesh, K., & Panneerselvam, K. (2017) · Archives of Metallurgy and Materials · doi:10.1515/amm-2017-0273 · Cited by 16
Alajmi, M., Alfares, F. S., & Alfares, M. S. (2017) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-017-1326-2 · Cited by 16
Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel
Ochengo, D., Li, L., Wei, Z., & Ning, H. (2022) · Advances in Materials Science and Engineering · doi:10.1155/2022/2675003 · Cited by 18
“&e S/N ratio is defined as the desired signal ratio for the undesired random noise value and shows the quality characteristics of the experimental data [45].”
BackgroundKamboj, A., Kumar, S., & Singh, H. (2015) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-015-0612-1 · Cited by 14
Sakthivel, M., Vijayakumar, S., & Jenarthanan, M. P. (2017) · Pigment & Resin Technology · doi:10.1108/prt-10-2015-0099 · Cited by 14
Juliyana, S. J., Prakash, J. U., Sadhana, A. D., et al. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.11.213 · Cited by 14
Sukmana, N. C., Khifdillah, M. I., Nurkholil, A. S., & Anggarini, U. (2019) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/509/1/012095 · Cited by 14
“Traditional experimental designs are too complex and the number of experiments will be more and more along with the many parameters being studied [9].”
BackgroundSingh, P. K., Kumar, K. S., & Saini, P. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.02.611 · Cited by 15
Parametric Modeling in Drilling of Die Steels using Taguchi Method based Response Surface Analysis
Vipin, V., Kant, S., & Jawalkar, C. S. (2018) · Materials Today Proceedings · doi:10.1016/j.matpr.2017.12.023 · Cited by 15
Optimization of Molding Process Parameter for Jute Reinforced Poly Lactic Acid Composite
Ramachandran, M., & Modia, B. A. (2020) · Journal of Advanced Research in Fluid Mechanics and Thermal Sciences · doi:10.37934/arfmts.71.1.117124 · Cited by 12
“Polylactic acid (PLA) is known for its renewability and biodegradability when compared to other composite resins [4].”
BackgroundModeling and surface morphological study in drilling of Al 2024 alloy
Rajbongshi, S. K., Das, B., Rudra, P., Chophy, K. S., & Syiemlieh, D. (2023) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2023.12.025 · Cited by 13
Mohammed, N. H., & Wolla, D. W. (2022) · AIMS Materials Science · doi:10.3934/matersci.2022008 · Cited by 12
“[16] employed Taguchi method to optimize machining parameters for better surface roughness and hole diameter accuracy during dry drilling of composite material.”
MethodSreenivasulu, R. (2015) · Independent Journal of Management & Production · doi:10.14807/ijmp.v6i1.254 · Cited by 12
Optimisation of drilling parameters on St37 based on Taguchi method
Samavi, J., Goharimanesh, M., Akbari, A., & Dezyani, E. (2018) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-018-1245-y · Cited by 11
Kumar, S., Jagadish, J., & Ray, A. (2021) · Lecture notes in mechanical engineering · doi:10.1007/978-981-16-2347-9_31 · Cited by 11
Alao, A.-R., & Konneh, M. (2011) · Advanced materials research · doi:10.4028/www.scientific.net/amr.264-265.997 · Cited by 11
MINIMIZATION OF THE SHAPE ERROR IN THE INTERRUPTED GRINDING PROCESS BY USING TAGUCHI METHOD
Kurt, M., & Köklü, U. (2013) · Mechanika · doi:10.5755/j01.mech.18.6.3163 · Cited by 11
Self-citationSivasakthivel, P. S., Murugan, V., & Sudhakaran, R. (2012) · International Journal of Manufacturing Research · doi:10.1504/ijmr.2012.045241 · Cited by 11
“Mathematical models to predict surface roughness in terms of machining parameters such as spindle speed, feed rate and depth of cut have been developed by many researchers (Bagci and Aykut, 2006; Yang and Chen, 2001; Shather and Ibrheem, 2008; Kurt et al., 2009).”
BackgroundSreenivasulu, R., & Rao, C. S. (2016) · Independent Journal of Management & Production · doi:10.14807/ijmp.v7i2.414 · Cited by 11
Uwaezuoke, M. C., Ikeagwuani, C. C., & Okafor, F. O. (2025) · International Journal of Pavement Research and Technology · doi:10.1007/s42947-025-00601-9 · Cited by 12
Prediction of Optimal Process Parameters for Abrasive Assisted Drilling of SS304
Goyal, K. K., Jain, V., & Kumari, S. (2014) · Procedia Materials Science · doi:10.1016/j.mspro.2014.07.139 · Cited by 10
Shunmugesh, K., & Panneerselvam, K. (2017) · Materials Today Proceedings · doi:10.1016/j.matpr.2017.02.166 · Cited by 11
Shareef, I. R., Hussein, H. K., & Mahdi, B. L. (2023) · Advances in Science and Technology – Research Journal · doi:10.12913/22998624/174515 · Cited by 9
“F-value is a statistical instrument used to determine the de-sign factors have an important influence on the quality characteristic [35].”
MethodImran, A., Kim, S.-H., Woo, J., & Yi, B.-J. (2022) · IEEE Access · doi:10.1109/access.2022.3210247 · Cited by 9
Metadata
- Authors
- Kurt, M., Bagci, E., & Kaynak, Y.
- Affiliations
- Marmara University (TR)
- Corresponding author
- Kurt, Mustafa
- Venue
- The International Journal of Advanced Manufacturing Technology
- Published
- 2008-01-29
- Volume
- 40
- Issue
- 5-6
- Pages
- 458-469
- ISSN
- 0268-3768 (ISSN-L)
- 1433-3015
- OpenAlex
- W1975565563
- Semantic Scholar
- a8179511dc325b386f4d1cad642cafad2b8437cc
- Cited by
- 198
- References
- 25
- Citations by year
- 2026: 9 · 2025: 7 · 2024: 7 · 2023: 12 · 2022: 13 · 2021: 20 · 2020: 22 · 2019: 13 · 2018: 12 · 2017: 8 · 2016: 9 · 2015: 10 · 2014: 17 · 2013: 10 · 2012: 16
- FWCI
- 9.25
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.springer.com/tdm (tdm)
- Locations
- The International Journal of Advanced Manufacturing Technology (publishedVersion)
- Dspace Repository (Marmara Üniversitesi) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Keywords
- dry drilling, 2024 aluminum alloy, Taguchi method, cutting parameter optimization, surface finish, cutting speed, feed rate, depth of cut, TiN coated tools, TiAlN coated tools
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.