Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes
The DOI matches its Crossref record; 26 of the 26 references it cites were found in a registry or an index.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The most important characteristics of drilled-hole quality are surface roughness (SR) and the deviation of the hole size (HS) from its nominal diameter [2].”
From Optimization and Modeling of Process Parameters in Multi-Hole Simultaneous Drilling Using Taguchi Method and Fuzzy Logic Approach (2020) · cites this paper as [2]
Citations
Cites
Taguchi Techniques for Quality Engineering
Bement, T. R. (1989) · Technometrics · doi:10.1080/00401706.1989.10488519 · Cited by 2,718
Quality Engineering Using Robust Design
Kapur, K. C. (1990) · Journal of Quality Technology · doi:10.1080/00224065.1990.11979247 · Cited by 2,125
Introduction to Quality Engineering
(2008) · WORLD SCIENTIFIC eBooks · doi:10.1142/9789812778697_0001 · Cited by 1,511
Design optimization of cutting parameters for turning operations based on the Taguchi method
Yang, W. H., & Tarng, Y. S. (1998) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(98)00079-x · Cited by 1,302 · cited 1×
“To solve this problem, the Taguchi method uses a special design of orthogonal arrays to study the entire parameter space with only a small number of experiments [ 15 ].”
MethodQuality Engineering using Design of Experiments
Phadke, M. S. (1989) · Quality Control, Robust Design, and the Taguchi Method · doi:10.1007/978-1-4684-1472-1_3 · Cited by 585
Taguchi Techniques for Quality Engineering
Ziegel, E. R. (1997) · Technometrics · doi:10.1080/00401706.1997.10485460 · Cited by 533
Tsao, C. C., & Hocheng, H. (2004) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2004.02.019 · Cited by 368
Quality Engineering Using Robust Design
Menten, T. (1991) · Technometrics · doi:10.1080/00401706.1991.10484810 · Cited by 296
Experimental analysis and optimisation of tool wear in dry machining of aluminium alloys
Nouari, M., List, G., Girot, F., & Coupard, D. (2003) · Wear · doi:10.1016/s0043-1648(03)00105-4 · Cited by 284
Minimal lubrication machining of aluminium alloys
Kelly, J. F., & Cotterell, M. G. (2002) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(01)01126-8 · Cited by 242
Research works printed but not linked: 2
- Lou MS, Chen JC, Li CM (1998) Surface roughness prediction technique for CNC end-milling. J Ind Technol 15:1–6
- Yang JL, Chen JC (2001) A systematic approach for identifying optimum surface roughness performance in end-milling operations. J Ind Technol 17:1–8
Cited by
Items 101–198 of 198
Severino, G., de Paiva, E. J., Ferreira, J. R., et al. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-3947-0 · Cited by 9
“[7] used arrays of Taguchi to optimize the drilling process of Al 2024 alloy.”
MethodAnalysis and optimization of circularity error in drilling Process using statistical technique
Venkateshwarlu, N., Singaravel, B., Shekar, K. C., et al. (2021) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1057/1/012063 · Cited by 9
Understanding Surface Quality: Beyond Average Roughness (Ra)
Sahay, C., & Ghosh, S. (2020) · ASEE Annual Conference & Exposition · doi:10.18260/1-2--31176 · Cited by 9
“Numerous articles [2-11] have tried to address the dependence of the condition of surface and its performance on the machining process parameters.”
BackgroundLi, X., Deng, C., Wu, Y., et al. (2024) · Measurement Science and Technology · doi:10.1088/1361-6501/ad4bfb · Cited by 8
“Deep-hole parts e.g. hydraulic cylinders, aircraft landing gears, automotive fuel injectors and gun barrels have been widely used in modern industries [1–3].”
MethodTabacaru, V. (2020) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/916/1/012117 · Cited by 10
Kurt, R., & Can, A. (2021) · BioResources · doi:10.15376/biores.16.1.1642-1653 · Cited by 8
“The S/N ratio is defined as the desired signal ratio for the undesired random noise value and shows the quality characteristics of the experimental data (Kurt et al. 2009; Günay et al. 2011; Günay and Yücel 2013).”
Riaz, A. A., Muhammad, R., Ullah, N., Hussain, G., Alkahtani, M. S., & Akram, W. (2021) · Metals · doi:10.3390/met11020277 · Cited by 9
“Air vehicles and fast-moving objects are subjected to constant vibration and shock loads where fastener holes are prone to stress concentration and fatigue loads [3].”
BackgroundSrivastava, V., & Gupta, M. (2022) · International Journal of Engineering · doi:10.5829/ije.2022.35.10a.04 · Cited by 8
“The MAPE is computed using Equation (11) [27].”
MethodEffect of Rake Angle on Surface Roughness in CNC Turning
Ranganath, M. S., & Vipin, V. (2014) · International Journal of Advance Research and Innovation · doi:10.51976/ijari.221420 · Cited by 8
Cycle Time Reduction in CNC Turning Process Using Six Sigma Methodology – A Manufacturing Case Study
Manoj, K. S., Kar, B., Agrawal, R., Manupati, V. K., & Machado, J. (2021) · Lecture notes in mechanical engineering · doi:10.1007/978-3-030-79165-0_13 · Cited by 11
Performance Analysis of Soluble Bridge Plug Materials for Fracturing in Unconventional Oilfields
Wang, J., Jia, H., & You, J. (2022) · Mathematical Problems in Engineering · doi:10.1155/2022/1911173 · Cited by 7
“(e soluble bridge plug is mainly composed of the bridge plug base, the anchoring mechanism, and the sealing part [5, 8, 9].”
BackgroundRetractedOptimization of manufacturing parameters for Fe–25Cr–13Co magnetic alloy by using Taguchi technique
Haider, A., Jaffery, S. H. I., Khan, A. N., et al. (2023) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-023-11201-x · Cited by 7
“Design of experiments The Taguchi method is applied for engineering problems where several processes involve multiple responses [31, 32].”
MethodApplication of Robust Design Approach for Design Parameterization in Kansei Engineering
Sutono, S. B., Taha, Z., Abdul‐Rashid, S. H., et al. (2012) · Advanced materials research · doi:10.4028/www.scientific.net/amr.479-481.1670 · Cited by 7
“For instance, in mechanical engineering and especially in manufacturing , this method has been used for machining and processing [15,16,17], material design and strength [18,19], and product development [20,21,22].”
MethodExtreme Learning Machine and Particle Swarm Optimization in optimizing CNC turning operation
Janahiraman, T. V., Ahmad, N., & Nordin, F. H. (2018) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/342/1/012086 · Cited by 6
“…that the experimental design based optimization techniques can achieve the desired performances for not only in turning operations [12] but also in many manufacturing operation such as drilling [13, 14], milling [15], injection moulding [16, 17], and electrical discharge machining [18, 19].”
BackgroundBronis, M., Miko, E., & Nozdrzykowski, K. (2022) · Materials · doi:10.3390/ma16010110 · Cited by 8
“[22] proposed a model to predict the hole diameter accuracy relative to the drilling depth (d = 15; 25 mm), the drill bit coating (HSS+TiN, HSS+TiAlN, or uncoated HSS), the cutting speed (vc = 30, 45, and 60 m/min), and the feed per revolution ( fn = 0.”
BackgroundPrediction of cutting force and surface roughness using Taguchi technique for aluminum alloy AA6061
Yahya, E., Ding, G., & Qin, S. (2016) · Australian Journal of Mechanical Engineering · doi:10.1080/14484846.2015.1093220 · Cited by 6
“The S/N ratio is defined as the desired signal ratio for the undesired random noise value and shows the quality characteristics of the experimental data (Kurt, Bagci, and Kaynak 2009; Gunay, Kacal, and Turgut 2011).”
BackgroundMethodNikam, K. G., & Kadam, S. (2014) · Cited by 6
JaisonBaby, & Shunmugesh, K. (2019) · Materials Today Proceedings · doi:10.1016/j.matpr.2018.12.024 · Cited by 6
Optimization of Accuracy and Surface Finish of Drilled Holes in 350 Mild Steel
Pramanik, A., Basak, A. K., Islam, M. N., Dong, Y., Debnath, S., & Vora, J. J. (2019) · Springer series in advanced manufacturing · doi:10.1007/978-3-030-19638-7_3 · Cited by 7
Analyzing the Effects of the Kinematic System on the Quality of Holes Drilled in 42CrMo4 + QT Steel
Bronis, M., Miko, E., & Nowakowski, Ł. (2021) · Materials · doi:10.3390/ma14144046 · Cited by 8
Influence of the Kinematic System on the Geometrical and Dimensional Accuracy of Holes in Drilling
Bronis, M., Miko, E., & Nowakowski, Ł. (2021) · Materials · doi:10.3390/ma14164568 · Cited by 8
“Kurt, Bagci, and Kaynak [10] developed a model for determining the hole diameter accuracy for four input parameters: depth of drilling, drill bit coating type, cutting speed, and feed per revolution.”
BackgroundRao, S. U., & Rodrigues, L. L. R. (2012) · Cited by 6
Reddy, T. S., Banik, T., Velagala, R., et al. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.04.326 · Cited by 6
Kumari, S., Goyal, K. K., & Jain, V. (2013) · Cited by 5
Effects of the cutting fluid reduction on the dimensional quality of holes
Zeilmann, R. P., Vacaro, T., Bordin, F. M., & Soares, R. M. (2014) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/0954405414535769 · Cited by 6
“They also obtained bell-shaped holes, but an inverse bell-shape, that is, a larger diameter was obtained at the beginning of the holes than at the bottom.(1) A hypothesis suggested to explain the different results obtained in this article is based on the formation of micro-welding zones on the hole surface.”
BackgroundResultInfluentialEffect of Canned Cycles on Drilled Hole Quality
Islam, M. N., Rafai, N. H., & Charoon, P. (2010) · Lecture notes in electrical engineering · doi:10.1007/978-90-481-8776-8_53 · Cited by 5
Kumar, P. P., Ruban, M., Daniel, S. A. A., et al. (2023) · Advances in Materials Science and Engineering · doi:10.1155/2023/3692311 · Cited by 4
Akdulum, A., & Kayır, Y. (2023) · Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi · doi:10.17341/gazimmfd.1136798 · Cited by 4
Deform 3D Simulation and Experimental Study in Machining of AISI 1020 Mild Steel
Hussain, A., Sharif, A., Siddiqi, M. U. R., Hussain, G., Getachew, M. T., & Muhammad, R. (2024) · Journal of Engineering · doi:10.1155/2024/9085919 · Cited by 4
Kang, S.-B., Gong, J., & Ume, I. C. (2011) · Volume 1: Advances in Aerospace Technology; Energy Water Nexus; Globalization of Engineering; Posters · doi:10.1115/imece2011-62766 · Cited by 4
Pai, A. R., Joshi, G., & Rane, S. (2019) · International Journal of Systems Assurance Engineering and Management · doi:10.1007/s13198-019-00833-6 · Cited by 4
Hnátík, J., Fulemová, J., Sklenička, J., et al. (2025) · Materials · doi:10.3390/ma18133145 · Cited by 3
“Kurt et al. [3] introduced various drilling processes commonly used in the aerospace and automotive industries, including electron beam machining, ultrasonic machining, electrochemical machining, and abrasive jet machining.”
Panneersel, T., & Raghuraman, S. (2012) · Journal of Applied Sciences · doi:10.3923/jas.2012.1063.1066 · Cited by 3
Parametric optimization of drilling on IS 10,343 Gr. 2A carbon steel by Taguchi method: A case study
Patel, N., Mojidra, P. G., & Dhrangdhria, H. J. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.03.259 · Cited by 3
Vookoti, U. S. V. P., Rao, K. V., & Satish Kumar, P. (2022) · Independent Journal of Management & Production · doi:10.14807/ijmp.v13i2.1617 · Cited by 3
Xing, K., Bonev, I. A., Liu, Z., et al. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-14475-x · Cited by 3
“Owing to its greatest advantages in the saving of the experiment time, number, and cost, the Taguchi method has been widely used in engineering area for factors optimization [21–23].”
Samtaş, G., & Korucu, S. (2018) · Journal of Polytechnic · doi:10.2339/politeknik.457957 · Cited by 3
Tool wear monitoring and replacement for tubesheet drilling
Griffin, R. C., Cao, Y., Peng, J., & Chen, D. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-8325-2 · Cited by 3
Bhargavi, Y., & Reddy, V. D. (2020) · Smart innovation, systems and technologies · doi:10.1007/978-981-15-1616-0_61 · Cited by 3
Juliyana, S. J., Prakash, J. U., Rubi, C. S., et al. (2025) · Discover Mechanical Engineering · doi:10.1007/s44245-025-00148-w · Cited by 2
Investigation of CNC Milling Machining Parameters on Surface Roughness
Alyas, R. R. (2018) · Al-Khwarizmi Engineering Journal · doi:10.22153/kej.2018.01.008 · Cited by 2
Determination of twist drill bits wear: the effect of the composition and structure of the steels
Prałat, K., Krupińska, A., Ochowiak, M., Włodarczak, S., Matuszak, M., Ciemnicka, J., Koper, A., & Wójcicka, K. (2022) · Green Sciences · doi:10.2478/pjct-2022-0016 · Cited by 3
Akdulum, A., Süzgünol, M., & Kayır, Y. (2025) · Gazi Üniversitesi Fen Bilimleri Dergisi Part C Tasarım ve Teknoloji · doi:10.29109/gujsc.1549251 · Cited by 2
Kumari, S., & Sonia, P. (2021) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1116/1/012144 · Cited by 2
“[10] observed the optimization of cutting parameters so that high finished surface and accurate hole diameter during drilling can be obtained.”
BackgroundMachining parameters optimization on micro hole vibration drilling using grey system theory
Lai, X., Yan, C., Zhan, C., et al. (2015) · IEEE International Conference on Mechatronics and Automation (ICMA) · doi:10.1109/icma.2015.7237846 · Cited by 2
Ayaz, M., Khaki, D. M., Arab, N. B. M., et al. (2013) · International Journal of Materials Research (formerly Zeitschrift fuer Metallkunde) · doi:10.3139/146.110973 · Cited by 2
Combining BPN and TM to build a prediction model of process parameters: a case study
Fu, H., Chen, C., Yeh, H., et al. (2015) · Total Quality Management & Business Excellence · doi:10.1080/14783363.2015.1040754 · Cited by 2
Pahuja, V., Kant, S., Jawalkar, C. S., & Verma, R. (2019) · Lecture notes on multidisciplinary industrial engineering · doi:10.1007/978-981-13-6287-3_9 · Cited by 3
Investigation of the Effect of Drill Bit Feature on Hole Surface Quality and Tool Wear
Kıyak, M. (2021) · DÜMF Mühendislik Dergisi · doi:10.24012/dumf.1002180 · Cited by 2
“1 mm/rev, taking into account the drill bit specifications and the relevant literature [2, 5, 10, 12, 13, 15, 18, 19].”
BackgroundMethodBalakumaran, V., Parthasarathy, C., & Chandradass, J. (2015) · Asian Review of Mechanical Engineering · doi:10.51983/arme-2015.4.2.2399 · Cited by 2
Ahmed, S., Yuvaraj, N., & Hariprasad, T. (2019) · FME Transaction · doi:10.5937/fmet1903634a · Cited by 2
Ikeagwuani, C. C., & Nwonu, D. C. (2021) · Geomechanics and Geoengineering · doi:10.1080/17486025.2021.1912402 · Cited by 2
“It is an extremely potent tool utilised in the production of superior-quality system (Kurt et al. 2009).”
MethodInfluentialAhmed, L. S., Natarajan, Y., & Hariprasad, T. (2019) · FME Transaction · doi:10.5937/fmet1903634s · Cited by 2
Faqeeh, A., & El-Gizawy, A. S. (2015) · SAE International Journal of Materials and Manufacturing · doi:10.4271/2014-01-9105 · Cited by 1
Wang, X., Wang, P., Yi, J., et al. (2024) · Transactions of the IMF · doi:10.1080/00202967.2024.2336722 · Cited by 1
Yang, T., Yang, Y., & Chen, C. (2011) · International Polymer Processing · doi:10.3139/217.2488 · Cited by 1
Rao, S. U., & Rodrigues, L. L. R. (2014) · Cited by 1
Design of Vibration Excitation Test Rig with Redundant Degree of Freedom
Wen, S., Zhang, Y., Shu-xin, H., et al. (2016) · International Journal of Control and Automation · doi:10.14257/ijca.2016.9.9.35 · Cited by 1
“For the orthogonal experimental scheme of three levels and three factors, it can be used L9(3(3)) experimental scheme [17-18].”
MethodSivam, S. P. S. S., Banerjee, A., & Kulkarni, A. (2019) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2019-28-0055 · Cited by 1
A RETROSPECTIVE ANALYSIS ON DRILLING OPERATION AND ITS PARAMETERS: A CRITICAL REVIEW
Varatharajulu, M., Duraiselvam, M., Jayaprakash, G., Baskar, N., Vijayaraj, S., & Babu, K. A. (2023) · Surface Review and Letters · doi:10.1142/s0218625x23300101 · Cited by 1
Postprocessing optimization for surface finishing by machine learning
Zhu, H., Zheng, G., Tian, Y., Higham, R., & Rennie, A. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-22145-3.00008-6 · Cited by 2
Stasiūnas, A., & Jurevičius, M. (2013) · Mokslas - Lietuvos ateitis · doi:10.3846/mla.2012.96 · Cited by 1
Khazini, L., Fatehifar, E., Fouladpanjeh, B., et al. (2014) · Energy Sources Part A Recovery Utilization and Environmental Effects · doi:10.1080/15567036.2010.550179 · Cited by 1
“The main advantages of Taguchi method is performance of experiments by saving time, cost, and finally it gets valuable information about the parameters in a short time (Kurt et al., 2009).”
MethodWan, L., Deng, Z. H., Li, S. C., et al. (2012) · Advanced materials research · doi:10.4028/www.scientific.net/amr.497.273 · Cited by 1
Revuru, R. S., Posinasetti, N. R., Amrita, M., et al. (2018) · Smart and Sustainable Manufacturing Systems · doi:10.1520/ssms20170010 · Cited by 1
Drillability of Titanium Alloy 6246 from Surface Quality Perspective
DARSIN, M., & Pasang, T. (2019) · Material Science Research India · doi:10.13005/msri/160111 · Cited by 1
Sabarish, K. V., & Parvati, T. S. (2020) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.06.099 · Cited by 1
Guo, Y., Cao, L., Sang, S., et al. (2021) · Anais da Academia Brasileira de Ciências · doi:10.1590/0001-3765202120190346 · Cited by 1
Optimize The Turning Parameter Using Taguchi Methodology
Mehdi, A. (2022) · International Journal of Scientific Research in Science and Technology · doi:10.32628/ijsrst218553 · Cited by 1
Lacombe, A. (2021) · theses.fr (ABES) · doi:10.70675/3d77233azf5f8z4d25zb681ze10b5eeca061 · Cited by 4
Design Optimization of Cutting Parameters when Drilling Metal Matrix Composites
Sriprateep, K., Inthidech, S., Singto, S., et al. (2011) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.121-126.1311
Rao, S. U., & Rodrigues, L. L. R. (2014)
Effect of Rake Angle on Dimensional Accuracy of Copper Micro-drilling
Sharma, V. K., & Ghuman, R. S. (2013)
Tool Condition Monitoring and Replacement for Tubesheet Drilling
Griffin, R. C. (2013) · University Library - University of Saskatchewan (University of Saskatchewan)
Optimization of Surface Roughness and Hole Diameter Accuracy for Drilling of EN- 31 Based on GRA
Kumar, S. (2018) · International Journal for Research in Applied Science and Engineering Technology · doi:10.22214/ijraset.2018.4150
Investigation of CNC Milling Machining Parameters on Surface Roughness
Alyas, R. R. (2018) · Al-Khwarizmi Engineering Journal · doi:10.22153/https://doi.org/10.22153/kej.2018.01.008
A Study on Parametric Appraisal of Drilling on Bio-compatible Materials
Chatterjee, S. (2014) · Cited by 2
Bhargavi, Y., Reddy, V. D., & Bhaskara, P. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.05.364
Experimental Optimization of Drilling Parameters in Tooling for Euro 7 Nozzle Production
KÜÇÜKTÜRK, H., KÜÇÜKTÜRK, G., Yavaş, Ç., et al. (2021) · International Journal of Automotive Science And Technology · doi:10.30939/ijastech..945993
Akkuş, H., & Yaka, H. (2021) · Celal Bayar Üniversitesi Fen Bilimleri Dergisi · doi:10.18466/cbayarfbe.898972
Optimization for Green Path in Wood Extractives by Taguchi Analysis
PEKGÖZLÜ, A. K., Ceylan, E., Gençer, A., & Kurt, R. (2022) · Drvna industrija · doi:10.5552/drvind.2022.2137
The Effect and Process Parameters During Conventional Drilling and Abrasive Water Jet Drilling
Varanasi, S., & Praveen, L. (2023) · International Journal For Multidisciplinary Research · doi:10.36948/ijfmr.2023.v05i04.4269 · Cited by 1
Assessment of Machinability in Aluminium Alloys Using the COPRAS Method
Arivudainambi, J., & Muthusamy, P. (2022) · doi:10.46632/dmfar/1/2/8
PROJEKSİYON KAYNAĞIN PROSES PARAMETRELERİNİN S355MC KLEVİS BRAKETİN BAĞLANTI PERFORMANSINA ETKİSİ
Arı, A., KORKMAZ, K., MÜHÜRDAR, B., et al. (2023) · Uludağ University Journal of The Faculty of Engineering · doi:10.17482/uumfd.1329959
Drilling performance on fly-ash geopolymers
Ghazali, M. F., Abdullah, M. M. A. B., Jamel, A. H., et al. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-24068-3.00013-3
Optimization of thrust and torque forces of EN8 in drilling with HSS
Gopalkrishna, P. V., Kishore, K., & Kumar, C. A. (2025) · Journal of Physics Conference Series · doi:10.1088/1742-6596/3066/1/012012
Pabalkar, V., Chanda, R. S., & Debjyoti (2025) · Lecture notes in networks and systems · doi:10.1007/978-981-96-7496-1_20
Sarı, H. (2026) · Mühendis ve Makina · doi:10.46399/muhendismakina.1760886
Sheng, Y., Huang, W., Fang, X., et al. (2026) · Infrastructures · doi:10.3390/infrastructures11040114
Kıyak, M. (2026) · MANUFACTURING TECHNOLOGY · doi:10.21062/mft.2026.024
The Optimization of Flow Drilling and Tapping on Thin-Walled Hollow Sections
Tunalıoğlu, M. Ş. (2026) · Engineering Perspective · doi:10.64808/engineeringperspective.1918985
Hole characteristics after drilling a titanium alloy: a study using plain drills and textured drills
Azim, S., Chetan, & Bartarya, G. (2026) · Materials and Manufacturing Processes · doi:10.1080/10426914.2026.2682787
Accuracy Analysis of Holes Drilled in Ductile Cast Iron with an HSS Helical Drill Bit
SÓJKA, R., Ziarkowski, P., KLAMCZYŃSKI, K., et al. (2026) · Materials · doi:10.3390/ma19122606
“Key process parameters affecting hole quality include cutting speed (v c ), feed rate (f n ), tool geometry (point angle, helix angle, and web thickness), workpiece material properties, and the cooling/lubrication strategy [1,2,10–12].”
CNTs Reinforced Aluminum 6061 MMCs’ Machining Parameters Optimized by Design of Experiment
Nand, S., Khan, N., & Krishna, C. M. (2026) · Lecture notes in mechanical engineering · doi:10.1007/978-981-96-9646-8_2
Effect of Al5Ti1B and Al10Sr added to Al2024 alloy on mechanical properties and machinability
Kanlı, E., Kocaman, E., Koçar, O., Köklü, U., Kaplan, R., Mesutoğlu, M., & Bakırcıoğlu, B. (2026) · Sadhana · doi:10.1007/s12046-026-03364-6
“In these studies, the effects of coated/un-coated cutting tools [33, 34], drill tip angle and helix angle [35–37], rotation speed [38–40], and feed rate [37, 40] on cutting force, burr formation, and surface roughness were investigated.”
Metadata
- Authors
- Kurt, M., Bagci, E., & Kaynak, Y.
- Affiliations
- Marmara University (TR)
- Corresponding author
- Kurt, Mustafa
- Venue
- The International Journal of Advanced Manufacturing Technology
- Published
- 2008-01-29
- Volume
- 40
- Issue
- 5-6
- Pages
- 458-469
- ISSN
- 0268-3768 (ISSN-L)
- 1433-3015
- OpenAlex
- W1975565563
- Semantic Scholar
- a8179511dc325b386f4d1cad642cafad2b8437cc
- Cited by
- 198
- References
- 25
- Citations by year
- 2026: 9 · 2025: 7 · 2024: 7 · 2023: 12 · 2022: 13 · 2021: 20 · 2020: 22 · 2019: 13 · 2018: 12 · 2017: 8 · 2016: 9 · 2015: 10 · 2014: 17 · 2013: 10 · 2012: 16
- FWCI
- 9.25
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.springer.com/tdm (tdm)
- Locations
- The International Journal of Advanced Manufacturing Technology (publishedVersion)
- Dspace Repository (Marmara Üniversitesi) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Keywords
- dry drilling, 2024 aluminum alloy, Taguchi method, cutting parameter optimization, surface finish, cutting speed, feed rate, depth of cut, TiN coated tools, TiAlN coated tools
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.