A metrological inspection method using micro-CT for the analysis of drilled holes in CFRP and titanium stacks
Open accessThe DOI matches its Crossref record; 50 of the 50 references it cites were found in a registry or an index.
Abstract
This paper demonstrates a novel method that combines X-ray computed tomography (CT) and image processing for investigating two materials with significantly different densities. CT is increasingly used in industrial applications of inspecting materials and defects. The limitations of the system and data reconstruction are continuously researched so as to improve the quality of the results. One of the most common issues in CT is beam hardening, frequently experienced in multi-material scanning. The materials examined to demonstrate the method are carbon fibre reinforced polymers (CFRP) and titanium alloy Ti6Al4V, often used in combination in industry to optimise the weight to strength ratio. The assembly of the materials is usually achieved by bolting and riveting, which requires drilling through the two materials together. The machining of these materials is difficult due to their higher specific properties and as a result tool wear is always an issue. CFRPs properties depend on the nature, orientation and bond of the fibres and as a result drilling affects their service life. The results of the method ensure the quality of the drilled holes by measuring the variation of the maximum diameter, circularity, positioning of the hole and an examining the entrance delamination and exit burrs by image processing.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures










Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source says what the claim attributes to it.
In the citing paper
“Temperatures higher than 180 ° C results in material softening, material degradation, and poor surface quality [2].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [2]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Image reconstruction from projections : the fundamentals of computerized tomography
Herman, G. T. (1980) · Academic Press eBooks · Cited by 1,993
Computed Tomography: Principles, Design, Artifacts, and Recent Advances
Hsieh, J. (2015) · doi:10.1117/3.2197756 · Cited by 1,400 · cited 1×
“The normalisation of the data in the reconstruction process causes the creation of this phantoms, and it is a common issue in high energy scans and in multi-material scans [1].”
BackgroundA review of mechanical drilling for composite laminates
Liu, D., Tang, Y., & Cong, W. L. (2012) · Composite Structures · doi:10.1016/j.compstruct.2011.11.024 · Cited by 781
Machining of Composite Materials
Teti, R. (2002) · CIRP Annals · doi:10.1016/s0007-8506(07)61703-x · Cited by 740 · cited 1×
“These materials are frequently combined by bolting and riveting to optimise the weight to strength ratio [13, 14].”
BackgroundComputed tomography for dimensional metrology
Kruth, J. P., Bartscher, M., Carmignato, S., Schmitt, R., De Chiffre, L., & Weckenmann, A. (2011) · CIRP Annals · doi:10.1016/j.cirp.2011.05.006 · Cited by 684
Drilling of fiber reinforced plastics: A review
Abrão, A. M., Faria, P. E., Rubio, J. C. C., Reis, P., & Davim, J. P. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.11.146 · Cited by 533
Study of delamination in drilling carbon fiber reinforced plastics (CFRP) using design experiments
Davim, J. P., & Reis, P. (2003) · Composite Structures · doi:10.1016/s0263-8223(02)00257-x · Cited by 471 · cited 1×
“7, subsequent analysis negates the entrance delamination that may have been compromised, although this effect is well known and previously quantified [22, 23, 28].”
BackgroundGaitonde, V. N., Karnik, S. R., Rubio, J. C., Correia, A. E., Abrão, A. M., & Davim, J. P. (2008) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.10.050 · Cited by 410
Comprehensive analysis of delamination in drilling of composite materials with various drill bits
Hocheng, H., & Tsao, C. C. (2003) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(03)00749-0 · Cited by 378
Tsao, C. C., & Hocheng, H. (2004) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2004.02.019 · Cited by 368 · cited 1×
“7, subsequent analysis negates the entrance delamination that may have been compromised, although this effect is well known and previously quantified [22, 23, 28].”
Background
Research works printed but not linked: 3
- Herman GT (2009) Fundamentals of computed tomography - image reconstruction from projections. Springer, London 3. Kruth JP, Bartscher M, Carmignato S, Schmitt R, De ChiffreL, Weckenmann A (2011) Computed tomography for dimen- sional metrology. CIRP Ann 2011 -Manuf Technol 60:821- 842
- Weib D, Lonardoni R, Deffner A, Kuhn C (2012) Geometric image distortion in flat-panel X-ray detectos and its influence on the accuracy of CT-based dimensional measurements, iCT Conference Austria
- VDI/VDE (2010) Computed tomography in dimensional mea- surements. Measurement procedure and comparability VDI/VDE 2630 Part 1:4
Cited by
Hu, B., Konaklieva, S., Kourra, N., Williams, M. A., Ran, L., & Lai, W. (2021) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2019.2958737 · Cited by 46
“The voids may grow in operation [11], and work is needed to understand the characteristics of the growth.”
BackgroundSelf-citationLarge-field detection of Metal/CFRP hybrid composites based on air-coupled laser ultrasound
Long, B., Cheng, Z., Liao, W., Wu, J., Zeng, L., & Ji, X. (2024) · Composites Communications · doi:10.1016/j.coco.2024.102174 · Cited by 14
Motorcu, A., & Ekici, E. (2022) · FME Transactions · doi:10.5937/fme2203441m · Cited by 12
“ensure the quality of the drilled holes by measuring the maximum diameter variation, roundness, and hole positioning in CFRP/Ti6Al4V stacks with X-ray computed tomography (CT) and image processing method and examining the entry delamination and exit burrs with image processing [2].”
BackgroundMethodAir gap effects on dimensional accuracy in multi-material X-ray CT measurements
Drégelyi-Kiss, Á., & Marczis, A. (2025) · Results in Engineering · doi:10.1016/j.rineng.2025.108408 · Cited by 2
Quantification of Drill Hole Damages in CFRP Laminates Using High-Resolution Ultrasonic Testing
Jack, D. A., Ravindranath, P. K., Matalgah, K., & Fleck, T. J. (2024) · IEEE Open Journal of Instrumentation and Measurement · doi:10.1109/ojim.2024.3487238 · Cited by 2
“Over the last few years, X-ray computed tomography (CT) has become increasingly popular as an NDT technique in industry [22], [23], [24].”
Metadata
- Authors
- Kourra, N., Warnett, J. M., Attridge, A., Dahnel, A., Ascroft, H., Barnes, S., & Williams, M. A.
- Affiliations
- University of Warwick (GB)
- Corresponding author
- Kourra, Nadia
- Venue
- The International Journal of Advanced Manufacturing Technology
- Published
- 2016-05-14
- Volume
- 88
- Issue
- 5-8
- Pages
- 1417-1427
- ISSN
- 0268-3768 (ISSN-L)
- 1433-3015
- OpenAlex
- W2362243662
- Cited by
- 11
- References
- 50
- Citations by year
- 2026: 2 · 2025: 2 · 2024: 2 · 2022: 1 · 2020: 1 · 2019: 1 · 2017: 1 · 2016: 1
- FWCI
- 0.48
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- The International Journal of Advanced Manufacturing Technology (publishedVersion, cc-by)
- The International Islamic University Malaysia Repository (The International Islamic University Malaysia) (acceptedVersion)
- Warwick Research Archive Portal (University of Warwick) (acceptedVersion)
- Funders
- Engineering and Physical Sciences Research Council
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › Advanced X-ray and CT Imaging
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Industrial Vision Systems and Defect Detection
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Measurement and Metrology Techniques
- Keywords
- drilled holes, carbon fiber reinforced polymer, Ti-6Al-4V titanium alloy, hybrid composites, computed tomography, beam hardening, hole diameter measurement, circularity, burr formation, delamination, image processing, tool wear
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A metrological inspection method using micro-CT for the analysis of drilled holes in CFRP and titanium stacks. https://app.cochat.ai/papers/10.1007/s00170-016-8691-4
- The paper
- Kourra, N., Warnett, J. M., Attridge, A., Dahnel, A., Ascroft, H., Barnes, S., & Williams, M. A. (2017). A metrological inspection method using micro-CT for the analysis of drilled holes in CFRP and titanium stacks. The International Journal of Advanced Manufacturing Technology. https://doi.org/10.1007/s00170-016-8691-4
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.