CoChat

Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools

Open access
Younas, Muhammad, Khan, Mushtaq, Jaffery, Syed Husain Imran, Khan, Zarak, Khan, Nawar · 2024 · The International Journal of Advanced Manufacturing Technology

The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.

Abstract

This research studies the energy consumption and wear mechanism of carbide cutting tools in dry machining of Ti6Al4V alloy. In the first phase of experiments, full factorial design experiments were employed to study the tool wear rate (R) and specific cutting energy (SCE) with respect to the machining conditions (cutting speed and feed rate). Results showed that machining responses such as tool wear and energy consumption are affected by cutting conditions, thus requiring investigation to understand the wear mechanisms. Therefore, in the second phase, additional experiments were performed to investigate the tool-workpiece interactions at the cutting conditions reported to have low, moderate, and high tool wear. It was revealed that strong adhesion and material transfer between the tool and workpiece caused high wear. Electron dispersive X-ray spectroscopy (EDX) analysis of worn tools showed that the transfer of tungsten (W) and cobalt (Co) to the workpiece and titanium to the tool surface is the primary cause of tool deterioration. As a result, diffusion and dissolution have degraded cutting performance and weakened the tool edge, leading to rapid wear. Furthermore, worn tools resulted in relatively higher energy consumption per unit volume of material removed at the tooltip. The degradation of cutting performance and weakening of the tool edge results in rapid wear and higher energy consumption. The study suggests that minimizing tool wear is crucial for energy reduction, improved sustainability, and cleaner production goals in dry machining of titanium-based alloys.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1007/s00170-024-13548-1

Cites

28 of 28 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 28 references

Research works printed but not linked: 10

  1. Stephenson DA, Agapiou JS (2023) Metal cutting theory and practice. CRC press
  2. Goindi G, production PSJ of cleaner, (2017 undefined) Dry machining: a step towards sustainable machining–challenges and future directions. Elsevier [Internet] [cited 2023 Apr 8]; Available from: https://www.sciencedirect.com/science/article/pii/S0959652617316918?casa_token=J8dLpiJy4EoAAAAA:adLPApGGfhDo0dSdDU-E7mdmp2r7QsqkpFTw7066hmZXg0O0QMjfUNi7XgWuVjUq4KzH8wEB. Accessed 8 Apr 2023
  3. Gu J, Barber G, Tung S, Wear RG, (1999 undefined) Tool life and wear mechanism of uncoated and coated milling inserts. Elsevier [Internet] [cited 2023 Apr 8]; Available from: https://www.sciencedirect.com/science/article/pii/S0043164899000745?casa_token=Nt-YakYSK1IAAAAA:YJii-89JY2Cg-uF7yG5Qg_sNARudqqzYSSmDWUouJL3boGwfMo3I2X1axPYxl6bzaamXgGk. Accessed 8 Apr 2023
  4. Ahmada R (2019) Process parameters and its effect on surface roughness during turning Ti6Al4V alloy. In: Advances in Manufacturing Technology XXXIII: Proceedings of the 17th International Conference on Manufacturing Research, incorporating the 34th National Conference on Manufacturing Research, 10-12 September 2019. Queen's University, Belfast, vol 9. IOS Press, p 303
  5. Khan M, Warsi SS, Jaffery SH, Ahmad R, Younas M (2019) Analysis of energy consumption in orthogonal machining of Al 6061-T6 alloy. In: Advances in Manufacturing Technology XXXIII: Proceedings of the 17th International Conference on Manufacturing Research, incorporating the 34th National Conference on Manufacturing Research, 10–12 September 2019. Queen's University, Belfast, vol 9. IOS Press, p 327
  6. Khan MA, Jaffery SHI, Khan M (2023) Assessment of sustainability of machining Ti-6Al-4V under cryogenic condition using energy map approach. Eng Sci Technol Int J 41:101357 https://www.sciencedirect.com/science/article/pii/S2215098623000344
  7. Khan MA, Jaffery SHI, Khan M, Younas M, Butt SI, Ahmad R et al (2020) Multi-objective optimization of turning titanium-based alloy Ti-6Al-4V under dry, wet, and cryogenic conditions using gray relational analysis (GRA). Int J Adv Manuf Technol 106:3897–911 · DOI
  8. Groover MP (2020) Fundamentals of modern manufacturing: materials, processes, and systems. John Wiley & Sons
  9. Astakhov VP, Shvets S. (2004) The assessment of plastic deformation in metal cutting. J Mater Process Technol [Internet] [cited 2023 Apr 25];146:193–202. Available from: https://linkinghub.elsevier.com/retrieve/pii/S0924013603009981 · DOI · Paper page
  10. (2008) Machining dynamics: theory, applications and practices, London: Springer

Cited by

See all 17

Metadata

Authors
Younas, M., Khan, M., Jaffery, S. H. I., Khan, Z., & Khan, N.
Affiliations
  • Robert Gordon University (GB)
  • Prince Mohammad bin Fahd University (SA)
  • National University of Sciences and Technology (PK)
  • HITEC University (PK)
  • Riphah International University (PK)
Corresponding author
  • Younas, Muhammad
  • Khan, Mushtaq
  • Jaffery, Syed Husain Imran
  • Khan, Zarak
  • Khan, Nawar
Venue
The International Journal of Advanced Manufacturing Technology
Published
2024-04-16
Volume
132
Issue
7-8
Pages
3785-3799
ISSN
  • 0268-3768 (ISSN-L)
  • 1433-3015
OpenAlex
W4394856314
Cited by
17
References
28
Citations by year
2026: 9 · 2025: 6 · 2024: 2
FWCI
2.28
Type
journal article
Language
en
Open access
Licence
Locations
  • The International Journal of Advanced Manufacturing Technology (publishedVersion, cc-by)
  • Greenwich Academic Literature Archive (University of Greenwich) (submittedVersion)
  • Open Access Institutional Repository at Robert Gordon University (Robert Gordon University) (submittedVersion, cc-by)
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
  • Physical Sciences › Materials Science › Metals and Alloys › Metal Alloys Wear and Properties
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
Keywords
Ti-6Al-4V, titanium alloy machining, tool wear, specific cutting energy, dry machining, uncoated carbide tools, tool-workpiece interaction, adhesion, material transfer, cutting speed, feed rate, energy consumption

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools. https://app.cochat.ai/papers/10.1007/s00170-024-13548-1
The paper
Younas, M., Khan, M., Jaffery, S. H. I., Khan, Z., & Khan, N. (2024). Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools. The International Journal of Advanced Manufacturing Technology. https://doi.org/10.1007/s00170-024-13548-1

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.