Non-Newtonian mixed elastohydrodynamics of differential hypoid gears at high loads
Open accessThe DOI matches its Crossref record; 60 of the 60 references it cites were found in a registry or an index.
Abstract
Prediction of friction and transmission efficiency are design objectives in transmission engineering. Unlike spur and helical involute gears, there is a dearth of numerical analysis in the case of hypoid gear pairs. In particular, it is important to take into account the side leakage of the lubricant from the contact as the result of the lubricant entrainment at an angle to the elliptical contact footprint. In the automobile differential hypoid gears, high loads result in non-Newtonian behaviour of the lubricant, which may exceed its limiting shear stress, a fact which has not been taken into account in the open literature. This results in conditions which deviate from observed experimental tractive behaviour. The paper takes into account these salient practical features of hypoid gear pair analysis under high load. It highlights a non-Newtonian shear model, which limits the lubricant shear behaviour. Prediction of friction and transmission efficiency is in line with those reported in the literature.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The roughness parameter ζ u1D6FD u1D70E of combined represented surfaces typically ranges between 0.04 and 0.07 [38].”
From Application of Tribological Artificial Neural Networks in Machine Elements (2023) · cites this paper as [38]
Citations
Cites
Viscosity, Plasticity, and Diffusion as Examples of Absolute Reaction Rates
Eyring, H. (1936) · The Journal of Chemical Physics · doi:10.1063/1.1749836 · Cited by 3,218
Patir, N., & Cheng, H. S. (1978) · Journal of Lubrication Technology · doi:10.1115/1.3453103 · Cited by 2,305
The Contact of Two Nominally Flat Rough Surfaces
Greenwood, J. A., & Tripp, J. H. (1970) · Proceedings of the Institution of Mechanical Engineers · doi:10.1243/pime_proc_1970_185_069_02 · Cited by 1,754
A numerical solution to the elasto-hydrodynamic problem
Dowson, D., & Higginson, G. R. (1959) · Journal of Mechanical Engineering Science · doi:10.1243/jmes_jour_1959_001_004_02 · Cited by 663
Shear behaviour of elastohydrodynamic oil films
Johnson, K. L., & Tevaarwerk, J. L. (1977) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1977.0129 · Cited by 515
The shear properties of Langmuir—Blodgett layers
Briscoe, B. J., & Evans, D. C. B. (1982) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1982.0048 · Cited by 411
Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part IV—Starvation Results
Hamrock, B. J., & Dowson, D. (1977) · Journal of Lubrication Technology · doi:10.1115/1.3452973 · Cited by 269
Gohar, R., & Rahnejat, H. (2018) · doi:10.1142/q0152 · Cited by 251
Self-citationShear Strength Measurements of Lubricants at High Pressure
Bair, S., & Winer, W. O. (1979) · Journal of Lubrication Technology · doi:10.1115/1.3453339 · Cited by 230
Instantaneous Coefficients of Gear Tooth Friction
Benedict, G. H., & Kelley, B. W. (1961) · A S L E Transactions · doi:10.1080/05698196108972420 · Cited by 201
Research works printed but not linked: 9
- Rahnejat H (2010) Tribology and dynamics of engine and powertrain. Woodhead, Cambridge
- Misharin YA (1958) Influence of the friction condition on the magnitude of the friction coefficient in the case of rollers with sliding. In: Proc int conf on gearing, IMechE, London, UK, pp 159–164
- Grubin AN (1949) Contact stresses in toothed gears and worm gears. Book 30 CSRI for technology and mechanical engineering. DSRI Trans, Moscow, p 337
- Vijayakar S (2000) CALYX manual. Advanced Numerical Solutions Inc, Columbus
- Roeland CJA (1966) Correlation aspect of the viscosity–temperature–pressure relation of lubrication oils. PhD Thesis, Delft University of Technology, The Netherlands
- Dowson D, Higginson GR (1959) A numerical solution to the elastohydrodynamic problem. Proc Inst Mech Eng, Part C, J Mech Eng Sci 1:6–15
- Swift HW (1932) The wetability of lubricating films in journal bearings. Minutes of the proc. J Inst Civ Eng 223:267–288
- Buckingham E (1963) Efficiencies of gears in analytical mechanics of gears. Dover, New York, pp 395–425
- Hurley JD (2009) An experimental investigation of thermal behaviour of an automotive rear axle. MSc thesis, The Ohio State University
Cited by
Ding, H., Tang, J., Zhong, J., & Zhou, Z. (2016) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2016.09.003 · Cited by 80
On the boundary conditions in multi-phase flow through the piston ring-cylinder liner conjunction
Shahmohamadi, H., Mohammadpour, M., Rahmani, R., Rahnejat, H., Garner, C. P., & Howell-Smith, S. (2015) · Tribology International · doi:10.1016/j.triboint.2015.04.025 · Cited by 71
“If the shear stress remains below the limiting shear stress of the lubricant [33,34], then the calculated value from Eq.”
BackgroundSelf-citationCao, W., Pu, W., Wang, J., & Xiao, K. (2018) · Tribology International · doi:10.1016/j.triboint.2018.03.015 · Cited by 62
Mohammadpour, M., Johns-Rahnejat, P. M., & Rahnejat, H. (2015) · Proceedings of the Institution of Mechanical Engineers Part K Journal of Multi-body Dynamics · doi:10.1177/1464419315569621 · Cited by 58
“The pressure distribution and the generated pressure spike determine the sub-surface stress field and the fatigue performance of rolling surfaces, as shown in Kannel and Tevaarwerk,2 Johns-Rahnejat and Gohar3 and Gohar and Rahnejat24 for point contact condition and Teodorescu et al.33 for line contact of lubricated ca…”
BackgroundSelf-citationPu, W., Wang, J., Yang, R., & Zhu, D. S. (2015) · Journal of Tribology · doi:10.1115/1.4030185 · Cited by 44
Metadata
- Authors
- Mohammadpour, M., Theodossiades, S., Rahnejat, H., & Saunders, T.
- Affiliations
- Loughborough University (GB)
- Ford Motor Company (United Kingdom) (GB)
- Corresponding author
- Theodossiades, S.
- Venue
- Meccanica
- Published
- 2013-12-19
- Volume
- 49
- Issue
- 5
- Pages
- 1115-1138
- ISSN
- 0025-6455 (ISSN-L)
- 1572-9648
- OpenAlex
- W2019171107
- Cited by
- 38
- References
- 58
- Citations by year
- 2025: 1 · 2024: 2 · 2022: 2 · 2021: 3 · 2020: 3 · 2019: 1 · 2018: 8 · 2017: 6 · 2016: 4 · 2015: 5 · 2014: 3
- FWCI
- 5.00
- Type
- journal article
- Language
- en
- Open access
- green
- dspace.lboro.ac.uk
- Licence
- cc-by-nc-nd
- www.springer.com/tdm (tdm)
- Locations
- Meccanica (publishedVersion)
- CLOK (University of Central Lancashire) (submittedVersion)
- Loughborough University Institutional Repository (Loughborough University) (submittedVersion, cc-by-nc-nd)
- Loughborough University Research Repository (Loughborough University) (submittedVersion, cc-by-nc-nd)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanics of Materials › Adhesion, Friction, and Surface Interactions
- Keywords
- hypoid gears, differential gear, elastohydrodynamic lubrication, friction prediction, transmission efficiency, high load
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Non-Newtonian mixed elastohydrodynamics of differential hypoid gears at high loads. https://app.cochat.ai/papers/10.1007/s11012-013-9857-x
- The paper
- Mohammadpour, M., Theodossiades, S., Rahnejat, H., & Saunders, T. (2014). Non-Newtonian mixed elastohydrodynamics of differential hypoid gears at high loads. Meccanica. https://doi.org/10.1007/s11012-013-9857-x
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.