Cited by 63High-Temperature Coating BehaviorsSurface Treatment and CoatingsErosion and Abrasive Machining
The DOI matches its Crossref record.
Investigations on the Behavior of HVOF and Cold Sprayed Ni-20Cr Coating on T22 Boiler Steel in Actual Boiler Environment
Bala, Niraj, Singh, Harpreet, Prakash, Satya, Karthikeyan, J.·2012·Journal of Thermal Spray Technology
Overview
Integrity signals
Registry
Crossref · 10.1007/s11666-011-9698-x
Cites
Statistics
Recomputing p-values needs the paper’s full text.
Verification
Claims the paper makes
We couldn’t retrieve this paper’s full text, so its claims and self-check weren’t run. The registry and citation checks still apply.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Bala et al. [92] reported that although cold-sprayed NiCr showed denser microstructure compared to the HVOF counterpart coating, yet HVOF NiCr coating preformed superior corrosion resistance in a boiler environment.”
From High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review (2024) · cites this paper as [92]
In the citing paper
“Moreover, it was found that, unlike the HVOF NiCr coating, the Cr2O3 layer of cold spray NiCr was discontinuous, which attributed to an inferior corrosion resistance of cold spray NiCr, compared to the HVOF counterpart.”
From High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review (2024) · cites this paper as [92]
In the citing paper
“Relatively low temperature of cold spray produced less amount of protective Cr2O3 compared to HVOF.”
From High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review (2024) · cites this paper as [92]
Citations
Cites
No references could be resolved yet.
Research works printed but not linked: 41
- T. Stoltenhoff, H. Kreye, H.J. Richter, and H. Assadi, Optimization of the Cold Spray Process, Thermal Spray 2001: New Surfaces for a Millennium, C.C. Berndt, K.A. Khor, and E.F. Lugscheider, Ed., ASM International, Materials Park, OH, 2001, p 409-416
- J.C. Tan, L. Looney, and M.S.J. Hashmi, Component Repair Using HVOF Thermal Spraying, J. Mater. Process. Technol., 1999, 92-93, p 203-208 · DOI
- L. Fedrizzi, S. Rossi, R. Cristel, and P.L. Bonora, Corrosion and Wear Behaviour of HVOF Cermet Coatings Used to Replaced Hard Chromium, Electrochim. Acta, 2004, 49, p 2803-2814 · DOI
- A.P. Alkimov, V.F. Kosarev, and A.N. Papyrin, A Method of Cold Gas-Dynamic Deposition, Sov. Phys. Dokl., 1990, 35(12), p 1047-1049
- N. Bala, H. Singh, and S. Prakash, An Overview of Cold Spray Technique, Mater. Sci. Forum, 2007, 561-565, p 2419-2422 · DOI
- V.H. Hidalgo, F.J.B. Varela, and E.F. Rico, Erosion Wear and Mechanical Properties of Plasma-Sprayed Nickel and Iron-Based Coatings Subjected to Service Conditions in Boilers, Tribol. Int., 1997, 30(9), p 641-649 · DOI
- B.Q. Wang, Erosion-Corrosion of Thermal Sprayed Coatings in FBC Boilers, Wear, 1996, 199, p 4-32
- H. Koivuluoto and P. Vuoristo, Effect of Ceramic Particles on Properties of Cold-sprayed Ni-20Cr + Al2O3 Coatings, J. Therm. Spray Technol., 2009, 18(4), p 555-562 · DOI
- H. Koivuluoto and P. Vuoristo, Structural Analysis of Cold-Sprayed Nickel-Based Metallic and Metallic-Ceramic Coatings, J. Therm. Spray Technol., 2010, 19(5), p 975-989 · DOI
- N. Bala, H. Singh, and S. Prakash, High Temperature Oxidation Studies of Cold Sprayed Ni-20Cr and Ni-50Cr Coatings on SAE 213-T22 Boiler Steel, Appl. Surf. Sci., 2009, 255(15), p 6862-6869 · DOI
- W.M. Zhao, Y. Wang, T. Han, K.Y. Wu, and J. Xue, Electrochemical Evaluation of Corrosion Resistance of NiCrBSi Coatings Deposited by HVOF, Surf. Coat. Technol., 2004, 183, p 118-125 · DOI
- W.M. Zhao, Y. Wang, L.X. Dong, K.Y. Wu, and J. Xue, Corrosion Mechanism of NiCrBSi Coatings Deposited by HVOF, Surf. Coat. Technol., 2005, 90, p 293-298 · DOI
- A. Scrivani, S. Lanelli, A. Rossi, R. Groppetti, F. Casadei, and G. Rizzi, A Contribution to the Surface Analysis and Characterization of HVOF Coatings for Petrochemical Application, Wear, 2001, 250, p 107-113 · DOI
- M.M. Helali and M.S.J. Hashmi, Proc. of the 10th Conference of the Irish Manufacturing Committee (IMC 10), Irish Manufacturing Committee, 1992, p 377-387
- L. Gil and M.H. Staia, Influence of HVOF Parameters on the Corrosion Resistance of NiWCrBSi Coatings, Thin Solid Films, 2002, 420-421, p 446-454 · DOI
- J.M. Miguel, J.M. Guilemany, and S. Vizcaino, Tribological Study of NiCrBSi Coating Obtained by Different Processes, Tribol. Int., 2003, 36, p 181-187 · DOI
- M.E. Aalamialeagha, S.J. Harris, and M. Emamighomi, Influence of the HVOF Spraying Process on the Microstructure and Corrosion Behaviour of Ni-20%Cr Coatings, J. Mater. Sci., 2003, 38, p 4587-4596 · DOI
- S. Sampath, X.Y. Jiang, J. Matejicek, L. Prchlik, A. Kulkarni, and A. Vaidya, Role of Thermal Spray Processing Method on the Microstructure, Residual Stress and Properties of Coatings, an Integrated Study of Ni-5 wt.% Al Bond Coats, Mater. Sci. Eng. A Struct., 2004, 364, p 216-231 · DOI
- R.S. Lima, J. Karthikeyan, C.M. Kay, J. Lindemann, and C.C. Berndt, Microstructural Characteristics of Cold-Sprayed Nanostructured WC-Co Coatings, Thin Solid Films, 2002, 416, p 129-135 · DOI
- B. Singh, “Studies on the Role of Coatings in Improving Resistance to Hot Corrosion and Degradation,” Ph.D. thesis, IITR, Roorkee, India, 2003
- H. Singh, “Hot Corrosion Studies of Plasma Sprayed Coatings Over Some Ni- and Fe-Based Superalloys,” Ph.D. thesis, IITR, Roorkee, India, 2005 · DOI
- R.C. McCune, W.T. Donlon, O.O. Popoola, and E.L. Cartwright, Characterization of Copper Layers Produced by Cold Gas-Dynamic Spraying, J. Therm. Spray Technol., 2000, 9(1), p 73-82 · DOI
- R.C. Dykhuizen and M.F. Smith, Gas Dynamic Principles of Cold Spray, J. Therm. Spray Technol., 1998, 7(2), p 205-212 · DOI
- A.H. Dent, A.J. Horlock, D.G. McCartney, and S.J. Harris, Microstructural Characterisation of a Ni-Cr-B-C Based Alloy Coating Produced by High Velocity Oxy-fuel Thermal Spraying, Surf. Coat. Technol., 2001, 9, p 244-250 · DOI
- G. Kong, D. Zhang, P.D. Brown, D.G. McCartney, and S.J. Harris, Microstructural Characterisation of High Velocity Oxy-fuel Thermally Sprayed Stellite-6, Mater. Sci. Technol., 2003, 19, p 1003-1011 · DOI
- D. Zhang, S.J. Harris, and D.G. McCartney, Microstructure Formation and Corrosion Behaviour in HVOF-Sprayed Inconel 625 Coatings, Mater. Sci. Eng. A, 2003, 344, p 45-56 · DOI
- P. Richer, M. Yandouzi, L. Beauvais, and B. Jodoin, Oxidation Behaviour of CoNiCrAlY Bond Coats Produced by Plasma, HVOF and Cold Gas Dynamic Spraying, Surf. Coat. Technol., 2010, 204, p 3962-3974 · DOI
- S. Prakash, B.S. Sidhu, and A. Madeshia, Proc. National Seminar on Advances in Material and Processing, Nov 9-10, 2001, IITR, Roorkee, 2001, p 245-253
- S. Srikanth, B. Ravikumar, S.K. Das, K. Gopalakrishna, K. Nandakumar, and P. Vijayan, Analysis of Failures in Boiler Tubes Due to Fireside Corrosion in a Waste Heat Recovery Boiler, Eng. Fail. Anal., 2003, 10, p 59-66 · DOI
- R.C. John, Slag Gas and Deposit Thermochemistry in a Coal Gasifier, J. Electrochem. Soc., 1986, 133(1), p 205-211 · DOI
- H.W. Nelson, H.H. Krause, E.W. Ungar, A.A. Putnam, C.J. Slunder, P.D. Miller, J.D. Hummel, and B.A. Landry, A Review of Available Information on Corrosion and Deposits in Coal and Oil-Fired Boilers and Gas Turbines, Report of ASME Research Committee on Corrosion and Deposits from Combustion Gases, Pergamon Press and ASME, New York, 1959
- S.E. Sadique, A.H. Mollah, M.S. Islam, M.M. Ali, M.H.H. Megat, and S. Basri, High-Temperature Oxidation Behavior of Iron-Chromium-Aluminum Alloys, Oxid. Met., 2000, 54(5-6), p 385-400 · DOI
- P.R. Krishnamoorthy, and P.R.S. Seetharamu, Proc. of LIPREX-89, Hyderabad, January 1989
- A.R. Nicholl and G. Wahl, The Effect of Alloying Additions on MCrAlY Systems—An Experimental Study, Thin Solid Films, 1983, 95, p 21-34 · DOI
- F. Stroosnijder, R. Mevrel, and M.J. Bennet, The Interaction of Surface Engineering and High Temperature Corrosion Protection, Mater. High Temp., 1994, 12(1), p 53-66 · DOI
- D. Toma, W. Brandl, and U. Koester, Studies on the Transient Stage of Oxidation of VPS and HVOF Sprayed MCrAlY Coatings, Surf. Coat. Technol., 1999, 120121, p 8-15 · DOI
- A. Ul-Hamid, Diverse Scaling Behavior of the Ni-20Cr Alloy, Mater. Chem. Phys., 2003, 80, p 135-142 · DOI
- T. Sundararajan, S. Kuroda, T. Itagaki, and F. Abe, Steam Oxidation Resistance of Ni-Cr Thermal Spray Coatings on 9Cr-1Mo Steel. Part 2: 50Ni-50Cr, ISIJ Int., 2003, 43(1), p 104-111 · DOI
- T. Sundararajan, S. Kuroda, K. Nishida, T. Itagaki, and F. Abe, Behaviour of Mn and Si in the Spray Powders During Steam Oxidation of Ni-Cr Thermal Spray Coatings, ISIJ Int., 2004, 44, p 139-144 · DOI
- H. Kaushal, H. Singh, and S. Prakash, High-Temperature Erosion-Corrosion Performance of High-Velocity Oxy-Fuel Sprayed Ni-20Cr Coating in Actual Boiler Environment, Metall. Mater. Trans. A, 2011, 42A, p 1836-1846 · DOI
- N. Bala, H. Singh, and S. Prakash, High Temperature Corrosion Behavior of Cold Spray Ni-20Cr Coating on Boiler Steel in Molten Salt Environment at 900 °C, J. Therm. Spray Technol., 2010, 19, p 110-118 · DOI
Cited by
Sorted by citations
Erosion–corrosion behaviour of Ni–20Cr plasma coating in actual boiler environment
Mishra, S. B., & Prakash, S. (2015) · Surface Engineering · doi:10.1179/1743294414y.0000000338 · Cited by 31
Self-citationHigh Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review
Khantisopon, K., Singh, S., Jitputti, J., Berndt, C. C., & Ang, A. S. M. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-024-10251-0 · Cited by 30
Metadata
- Authors
- Bala, N., Singh, H., Prakash, S., & Karthikeyan, J.
- Affiliations
- Indian Institute of Technology Ropar (IN)
- Indian Institute of Technology Roorkee (IN)
- Corresponding author
- Bala, Niraj
- Venue
- Journal of Thermal Spray Technology
- Published
- 2011-11-19
- Volume
- 21
- Issue
- 1
- Pages
- 144-158
- ISSN
- 1059-9630 (ISSN-L)
- 1544-1016
- OpenAlex
- W1997142746
- Cited by
- 63
- References
- 0
- Citations by year
- 2026: 2 · 2025: 1 · 2024: 4 · 2023: 3 · 2022: 4 · 2021: 9 · 2020: 5 · 2019: 6 · 2018: 4 · 2017: 3 · 2016: 2 · 2015: 9 · 2014: 4 · 2013: 6 · 2012: 1
- FWCI
- 6.03
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.springer.com/tdm (tdm)
- Locations
- Journal of Thermal Spray Technology (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › Surface Treatment and Coatings
- Physical Sciences › Engineering › Mechanical Engineering › Erosion and Abrasive Machining
- Keywords
- HVOF spraying, cold spray, high-temperature corrosion, erosion-corrosion, boiler tubes, superheater, erosion kinetics, weight loss, coating performance
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
