The DOI matches its Crossref record; 162 of the 162 references it cites were found in a registry or an index; 7 of the 97 sources its claims cite were checked for support.
High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review
Open accessAbstract
Abstract High temperature corrosion and slag deposition significantly reduce the thermal efficiency and lifespan of biomass-fired boilers. Surface modification with protective coatings can enhance boiler performance and prevent commercial losses due to maintenance and damage. This review focuses on the development of corrosion-resistant coatings (CRCs) and anti-slagging coatings (ASCs) over the past decade. CRCs are explored through thermal spray processes that include arc spray, atmospheric plasma spray (APS), high-velocity oxygen fuel (HVOF), detonation gun (D-gun™), and cold spray. Studies on alloys, ceramics, and ceramic–metal composites are summarised, highlighting the high temperature corrosion prevention mechanisms and discussing new coating materials. ASCs are reviewed in the context of advancements via thermal spray and slurry spray methods. The mechanisms for slag reduction, testing methods to evaluate ASC effectiveness, and the necessary architecture for preventing slag deposition are examined. A lab-based rig simulating fly ash deposition onto water-cooled coating coupons for anti-slagging investigations is also presented. Further research is needed to develop and evaluate materials for ASCs effectively. Graphical Abstract
Overview
CoChat Summary
## TL;DR
This review summarizes corrosion-resistant coatings and anti-slagging coatings for industrial boilers, emphasizing thermal spray as the main fabrication route and nickel-based high-chromium alloys as the most established corrosion-resistant materials. It also argues that anti-slagging coatings are less developed, that standardized evaluation methods are lacking, and that future work should focus on faster deposition methods and dual-function coatings that resist both corrosion and slagging.
## Key findings
- Thermal spray coatings are widely investigated for high-temperature corrosion resistance in boilers, with Ni-based high-chromium alloys described as the most used materials; their protection comes from Ni and Cr oxide/spinel formation.
- The review notes that NiCr alloys may not be the most economical option, and that lower-cost FeCr alloys are receiving research attention.
- For anti-slagging, the paper says progress lags behind corrosion-resistant coatings; reported slag-reduction mechanisms include preventing corrosion that promotes slag adhesion and using low-surface-energy materials such as hexagonal boron nitride (h-BN) to weaken slag adhesion/wettability.
- The paper reports several quantitative examples from prior studies: arc-sprayed Ni-50Cr showed superior protection; a modified-nozzle arc-sprayed NiCrTi/NiCrMo coating achieved coating porosity below 2% with particle velocities of 152 ± 26 m/s; cold-sprayed Ni-20Cr and Ni-50Cr reduced corrosion-erosion rates by 58% and 72%, respectively; adding 1 wt% and 2 wt% CNTs to Cr3C2–20NiCr reduced corrosion rates by 80.71% and 82.96%, respectively.
## Methods
- This is a narrative review of coating development for boilers over the past decade, covering corrosion-resistant coatings and anti-slagging coatings.
- It synthesizes literature on multiple deposition routes, including arc spray, APS, HVOF, D-gun™, cold spray, slurry spray, laser cladding, weld overlay, diffusion coatings, and liquid thermal spray/suspension plasma spray.
- For anti-slagging evaluation, it also describes literature-based test approaches such as shear/tensile adhesion strength tests, contact-angle measurements of molten ash, and a bespoke flame-spray “slag testing rig” that deposits artificial slag on water-cooled coupons.
## Limitations
- The paper states that anti-slagging coatings are much less explored than corrosion-resistant coatings, and that further research is needed to develop and evaluate anti-slagging materials effectively.
- The paper explicitly notes that there is no accepted standard test to evaluate slag/fouling resistance of boiler surfaces or coatings.
- It also states that ceramic coatings still need evaluation in functioning boilers, and that thermal mismatch on metallic boiler components is a challenge.
- Evident from the text: because this is a review rather than a new experimental study, the paper does not report a single unified dataset or head-to-head controlled comparison generated by the authors themselves.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
7 Valid · 13 Not valid · 66 Not checked · 59 Own results and interpretations
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“The alkali salt aerosols condense onto the heating surface of boilers to form a “sticky initial layer”.”
What the sources say
- Not checked — no full text of the sourcecites [7] M. Broström, S. Enestam, R. Backman, and K. Mäkelä, Fuel Processing Technology 105, 142 (2013 ). https://doi.org/10.1016/j.fuproc.2011.08.006. source
- Not checked — no full text of the sourcecites [8] X. Jin, J. Ye, L. Deng, and D. Che, Energy & Fuels 31, 2951 (2017). https://doi.org/10.1021/acs.energyfuels.6b03381. source
- Supportedcites [9] H. Zhang, C. Yu, and Z. Luo, RSC Advances 10, 21420 (2020). https://doi.org/10.1039/D0RA04370B. source
The Introduction says KCl and K₂SO₄ deposit on boiler superheaters mainly through condensation and thermophoresis, forming an innermost layer. The KCl condensation section describes a condensed KCl layer as sticky and able to capture fly ash. In this boiler, the authors observed a thin particle deposit before substantial KCl condensation, but that does not negate the broader statement attributed to the paper. (LLM, conf=0.87)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“For example, potassium sulphate (K2SO4) and sodium sulphate (Na2SO4) have been reported to cause insignificant damage after high temperature corrosion exposure if the protective oxidation scale of boiler steel remains intact and protective [18, 19].”
What the sources say
- Partly supportedcites [18] J. Pettersson, N. Folkeson, L.-G. Johansson, and J.-E. Svensson, Oxidation of Metals 76, 93 (2011). https://doi.org/10.1007/s11085-011-9240-z. sourceExperimental — accuracy not yet measured
The Discussion and Conclusions (page numbers unavailable) report that K2SO4 did not accelerate corrosion of 304L stainless steel under the tested conditions and had little effect on corrosion rate or surface morphology. The paper does not address Na2SO4, so it cannot support the claim about both sulphates. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [19] G. H. Meier, Oxidation of Metals 98, 1 (2022). https://doi.org/10.1007/s11085-020-10015-6. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Alloying element such as aluminium in nickel-based HVOF coatings also produces a protective layer of Al2O3 against corrosion attacks in both laboratory-scale and boiler environments [91, 104].”
What the sources say
- Not checked — no full text of the sourcecites [91] R. A. Mahesh, R. Jayaganthan, and S. Prakash, Surface Engineering 26, 413 (2010). https://doi.org/10.1179/174329409X451164. source
- Partly supportedcites [104] M. Bai, L. Reddy, and T. Hussain, Corrosion Science 135, 147 (2018). https://doi.org/10.1016/j.corsci.2018.02.047. sourceExperimental — accuracy not yet measured
Our copy supports the core of the claim for this source: Section 3.4 states 'the stainless steel was well protected by the deposition of NiAl coating with the formation of stable Al2O3 throughout the coatings', and Section 4.4 adds that 'chlorine was not able to further penetrate the Al2O3 scale at the coating/substrate interface, which ultimately protected the steel underneath from corrosion attack' for HVOF-sprayed β-NiAl on 304 steel. However, the evidence is a laboratory tube-furnace test (250 h, 700 °C, 500 ppm HCl in 5% O2/N2 with 10 wt% KCl deposit; Section 2.3 notes the gas is a 'simplified flue gas composition in biomass-fired boilers' and the setup was only 'designed based on industrial benchmark tests'), so the 'boiler environments' half of the claim — actual in-boiler exposure — is not demonstrated by this paper, which cites others for real boiler exposures (e.g. its refs 3, 6, 7, 12, 13). The paper also qualifies the protectiveness, noting severe corrosion initiating at uncoated sample edges, Al depletion and transformation to γ'-Ni3Al at the coating/steel interface after long-term service, and that temperatures below 700 °C 'may not be high enough to obtain a protective scale'. (LLM, conf=0.78)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Moreover, SPS offers a less complex approach to produce coatings that may potentially alter the wettability of molten ash particles in boilers compared to similar coating prepared by plasma spray physical vapour deposition (PS-PVD) [166].”
What the sources say
- Partly supportedcites [166] Y. Guo, et al., Advanced Science 10, 2205156 (2023). https://doi.org/10.1002/advs.202205156. sourceExperimental — accuracy not yet measured
The Conclusions (page unavailable) report that PS-PVD coatings can repel molten silicate, supporting the coating-wettability aspect of the claim. The paper does not assess SPS, compare its complexity with PS-PVD, or study ash particles in boilers; its stated application is turbine-engine coatings. (LLM, conf=0.84)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Nickel-based alloys are among the most widely used materials for high temperature corrosion-resistant HVOF coatings, as summarised in Table 4.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
62 more claims
Create a free account to see all 145 claims and to verify the 11 references still open.
- It may state two separate claims as one. 47
- Probably not a substantial claim. 38
- Borderline: one of the tests for a substantial claim is unclear. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Introduction
“The results showed that the use of low surface energy coatings such as h-BN reduces the contact angle of the molten ash in comparison with the surface of a bare steel.”
§ Introduction
“Thus, the poor wettability and reduced contact interface weakens the adhesion of the ash that accumulates on the boiler surface, and eventually, the slag will shed of its own accord owing to poor adhesion.”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“G. Singh, S. Kumar, and R. Kumar, Materials Research Express 7, 026527 (2020). https://doi.org/10.1088/2053-1591/ab6e7e. Article CAS Google Scholar”
Cited work 10.1088/2053-1591/ab6e7e · retracted 2021-01-13 · notice 10.1088/2053-1591/abd06a · this paper published 2024-07-10
Citations
Cites
1 retracted
Singh, G., Kumar, S., & Kumar, R. (2020) · Materials Research Express · doi:10.1088/2053-1591/ab6e7e · Cited by 21
RetractedBhushan, B., & Jung, Y. C. (2011) · Progress in Materials Science · doi:10.1016/j.pmatsci.2010.04.003 · Cited by 1,989
Niu, Y., Tan, H., & Hui, S. (2016) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2015.09.003 · Cited by 1,069
Fauchais, P. (2004) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/37/9/r02 · Cited by 777
Cold spray coating: review of material systems and future perspectives
Moridi, A., Hassani-Gangaraj, S. M., Guagliano, M., & Dao, M. (2014) · Surface Engineering · doi:10.1179/1743294414y.0000000270 · Cited by 754
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Geological survey professional paper 372. 1962
(1965) · Journal of Hydrology · doi:10.1016/0022-1694(65)90048-x · Cited by 504
Yuan, W., Li, R., Chen, Z., Gu, J., & Tian, Y. (2021) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2020.126582 · Cited by 363
High temperature corrosion of coatings and boiler steels below chlorine-containing salt deposits
Uusitalo, M. A., Vuoristo, P. M. J., & Mäntylä, T. A. (2004) · Corrosion Science · doi:10.1016/j.corsci.2003.09.026 · Cited by 260
Column Formation in Suspension Plasma-Sprayed Coatings and Resultant Thermal Properties
VanEvery, K., Krane, M. J. M., Trice, R. W., Wang, H., Porter, W., Besser, M., Sordelet, D., Ilavsky, J., & Almer, J. (2011) · Journal of Thermal Spray Technology · doi:10.1007/s11666-011-9632-2 · Cited by 253
Research works printed but not linked: 5
- J. J. Rowe, G. W. Morey, and C. S. Zen, Geological Survey Professional Paper 741, 1 (1972).
- P. Nguyen, S. Harding, and S. -Y. Ho, Experimental studies on slurry based thermal barrier coatings. in Proceedings of the 5th Australasian Congress on Applied Mechanics, (Engineers Australia, Brisbane, Qld, 2007), p. 545.
- W. F. Gale and T. C. Totemeier, 35.2 Chemical Vapour Deposition. in Smithells Metals Reference Book (8th Edition), (Elsevier. 2004).
- S. V. Joshi, D. Srinivasa Rao, and S. Centre for, N.-A. Technology of, and C. Other Developing, Surface Engineering, (Daya Publishing House, New Delhi, India, 2010). (in English).
- C. V. Maria, Sprays: Types, Technology and Modeling (Engineering Tools, Techniques and Tables), (Nova Science Publishers, Inc, New York, 2011). in English.
Cited by
Singh, A. N., Swain, S. K., Meena, A., et al. (2024) · Ceramics · doi:10.3390/ceramics7040121 · Cited by 24
“Within the next decade, we may expect the venture to discover a perfect material will come to see the light of the Sun and its applications in power plants and various high-temperature applications.”
Chen, H., Zhang, Z., Yin, S., Zhang, T., Song, T., & Lu, P. (2026) · Carbon Neutral Technologies · doi:10.1016/j.cnt.2026.100022 · Cited by 6
Wei, Z., Wang, L., Liang, X., Sharma, D., Zhu, H., Yuan, Z., & Wu, L. (2026) · Applied Energy · doi:10.1016/j.apenergy.2026.128092 · Cited by 7
Usman, A., Isern, L., Nicholls, J. R., Cordero-Cabrera, M. C., & Syed, A. U. (2025) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-025-11630-7 · Cited by 3
Ma, X., Zhu, J., Gao, C., et al. (2026) · Extreme Materials · doi:10.1016/j.exm.2026.01.002 · Cited by 2
Metadata
- Authors
- Khantisopon, K., Singh, S., Jitputti, J., Berndt, C. C., & Ang, A. S. M.
- Affiliations
- Australian Research Council (AU)
- SCG Chemicals (Thailand) (TH)
- Corresponding author
- Ang, Andrew S. M.
- Venue
- High Temperature Corrosion of Materials
- Published
- 2024-07-10
- Volume
- 101
- Issue
- S1
- Pages
- 1-55
- ISSN
- 2731-8397 (ISSN-L)
- 2731-8400
- OpenAlex
- W4400487032
- Cited by
- 30
- References
- 162
- Citations by year
- 2026: 20 · 2025: 9 · 2024: 1
- FWCI
- 0.70
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- High Temperature Corrosion of Materials (publishedVersion, cc-by)
- Funders
- ARC Industrial Transformation Training Centre (IC 180100005)
- Swinburne University of Technology
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › Surface Treatment and Coatings
- Physical Sciences › Materials Science › Ceramics and Composites › Advanced ceramic materials synthesis
- Keywords
- high-temperature corrosion, corrosion protection coatings, biomass boiler, slag deposition, thermal spraying, atmospheric plasma spraying, HVOF spraying, detonation spraying, cold spray, ceramic-metal composites, fly ash deposition
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review. https://app.cochat.ai/papers/10.1007/s11085-024-10251-0
- The paper
- Khantisopon, K., Singh, S., Jitputti, J., Berndt, C. C., & Ang, A. S. M. (2024). High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review. High Temperature Corrosion of Materials. https://doi.org/10.1007/s11085-024-10251-0
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.