The DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index.
Influence of tribology on global energy consumption, costs and emissions
Open accessAbstract
Calculations of the impact of friction and wear on energy consumption, economic expenditure, and CO2 emissions are presented on a global scale. This impact study covers the four main energy consuming sectors: transportation, manufacturing, power generation, and residential. Previously published four case studies on passenger cars, trucks and buses, paper machines and the mining industry were included in our detailed calculations as reference data in our current analyses. The following can be concluded: In total, ~23% (119 EJ) of the world’s total energy consumption originates from tribological contacts. Of that 20% (103 EJ) is used to overcome friction and 3% (16 EJ) is used to remanufacture worn parts and spare equipment due to wear and wear-related failures. By taking advantage of the new surface, materials, and lubrication technologies for friction reduction and wear protection in vehicles, machinery and other equipment worldwide, energy losses due to friction and wear could potentially be reduced by 40% in the long term (15 years)and by 18% in the short term (8 years). On global scale, these savings would amount to 1.4% of the GDP annually and 8.7% of the total energy consumption in the long term. The largest short term energy savings are envisioned in transportation (25%) and in the power generation (20%) while the potential savings in the manufacturing and residential sectors are estimated to be ~10%. In the longer terms, the savings would be 55%, 40%, 25%, and 20%, respectively. Implementing advanced tribological technologies can also reduce the CO2 emissions globally by as much as 1,460 MtCO2 and result in 450,000 million Euros cost savings in the short term. In the longer term, the reduction can be 3,140 MtCO2 and the cost savings 970,000 million Euros. Fifty years ago, wear and wear-related failures were a major concern for UK industry and their mitigation was considered to be the major contributor to potential economic savings by as much as 95% in ten years by the development and deployment of new tribological solutions. The corresponding estimated savings are today still of the same orders but the calculated contribution to cost reduction is about 74% by friction reduction and to 26% from better wear protection. Overall, wear appears to be more critical than friction as it may result in catastrophic failures and operational breakdowns that can adversely impact productivity and hence cost.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
(2014) · Cambridge University Press eBooks · doi:10.1017/cbo9781107415386 · Cited by 4,056
High-Entropy Alloys: A Critical Review
Tsai, M.-H., & Yeh, J.-W. (2014) · Materials Research Letters · doi:10.1080/21663831.2014.912690 · Cited by 3,477
The Geography of Transport Systems
Rodrigue, J.-P. (2020) · Routledge eBooks · doi:10.4324/9780429346323 · Cited by 2,970
The Science and Engineering of Thermal Spray Coatings
Pawlowski, L. (2008) · Wiley eBooks · doi:10.1002/9780470754085 · Cited by 2,033
Global energy consumption due to friction in passenger cars
Holmberg, K., Andersson, P., & Erdemir, A. (2012) · Tribology International · doi:10.1016/j.triboint.2011.11.022 · Cited by 1,614
Self-citationThe material footprint of nations
Wiedmann, T. O., Schandl, H., Lenzen, M., Moran, D., Suh, S., West, J., & Kanemoto, K. (2015) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1220362110 · Cited by 1,597
Graphene: a new emerging lubricant
Berman, D., Erdemir, A., & Sumant, A. V. (2014) · Materials Today · doi:10.1016/j.mattod.2013.12.003 · Cited by 1,480
Self-citationMacroscale superlubricity enabled by graphene nanoscroll formation
Berman, D., Deshmukh, S. A., Sankaranarayanan, S. K. R. S., Erdemir, A., & Sumant, A. V. (2015) · Science · doi:10.1126/science.1262024 · Cited by 943
Self-citationMaterial issues in additive manufacturing: A review
Singh, S., Ramakrishna, S., & Singh, R. (2017) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2016.11.006 · Cited by 899
Transportation Energy Data Book: Edition 16
Davis, S. C., McFarlin, D. N., & Laboratory, O. R. N. (2010) · ROSA P · doi:10.21949/1404021 · Cited by 849
The Geography of Transport Systems
Rodrigue, J.-P. (2013) · Routledge eBooks · doi:10.4324/9780203371183 · Cited by 743
Ionic Liquids as Lubricant Additives: A Review
Zhou, Y., & Qu, J. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b12489 · Cited by 628
Carbon-based tribofilms from lubricating oils
Erdemir, A., Ramirez, G., Eryilmaz, O. L., Narayanan, B., Liao, Y., Kamath, G., & Sankaranarayanan, S. K. R. S. (2016) · Nature · doi:10.1038/nature18948 · Cited by 578
Self-citationGlobal energy consumption due to friction and wear in the mining industry
Holmberg, K., Kivikytö-Reponen, P., Härkisaari, P., Valtonen, K., & Erdemir, A. (2017) · Tribology International · doi:10.1016/j.triboint.2017.05.010 · Cited by 534
Self-citationGlobal energy consumption due to friction in trucks and buses
Holmberg, K., Andersson, P., Nylund, N.-O., Mäkelä, K., & Erdemir, A. (2014) · Tribology International · doi:10.1016/j.triboint.2014.05.004 · Cited by 476
Self-citationTHE JOURNAL OF PHYSICAL CHEMISTRY
(1922) · Science · doi:10.1126/science.56.1446.304 · Cited by 466
Surface Engineering for Corrosion and Wear Resistance
(2001) · ASM International eBooks · doi:10.31399/asm.tb.secwr.9781627083157 · Cited by 418
Nanoscale wear as a stress-assisted chemical reaction
Jacobs, T. D. B., & Carpick, R. W. (2013) · Nature Nanotechnology · doi:10.1038/nnano.2012.255 · Cited by 361
Improving Tribological Performance of Piston Rings by Partial Surface Texturing
Kligerman, Y., Etsion, I., & Shinkarenko, A. (2005) · Journal of Tribology · doi:10.1115/1.1866171 · Cited by 361
2D-nanomaterials for controlling friction and wear at interfaces
Spear, J. C., Ewers, B. W., & Batteas, J. D. (2015) · Nano Today · doi:10.1016/j.nantod.2015.04.003 · Cited by 346
Superlubricity Achieved with Mixtures of Acids and Glycerol
Li, J., Zhang, C., Ma, L., Liu, Y., & Luo, J. (2013) · Langmuir · doi:10.1021/la3046115 · Cited by 164
Wälde, T. W. (2010) · Brill | Nijhoff eBooks · doi:10.1163/ej.9789004163300.i-1081.810 · Cited by 144
Green superlubricity of Nitinol 60 alloy against steel in presence of castor oil
Zeng, Q., Dong, G., & Martin, J. M. (2016) · Scientific Reports · doi:10.1038/srep29992 · Cited by 90
Tribological behavior of Ti6Al4V cellular structures produced by Selective Laser Melting
Bartolomeu, F., Sampaio, M., Carvalho, Ó. S. N., Pinto, E. M., Alves, N. M., Gomes, J. R., Silva, F. S., & Miranda, G. (2017) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2017.01.004 · Cited by 76
Kim, H., Seo, K.-J., Kang, K. H., & Kim, D. E. (2016) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-016-0102-0 · Cited by 67
Xu, J., & Li, J. (2015) · Friction · doi:10.1007/s40544-015-0100-8 · Cited by 49
Cha, Y., Hedberg, Y. S., Mei, N., & Olofsson, U. (2016) · Tribology Letters · doi:10.1007/s11249-016-0775-7 · Cited by 39
Future of Superhard Material Design, Processing and Manufacturing
Maweja, K., & Kanyanta, V. (2016) · Springer eBooks · doi:10.1007/978-3-319-29291-5_7 · Cited by 2
Cited by
Synthesis, structure, properties and applications of MXenes: Current status and perspectives
Ronchi, R. M., Arantes, J. T., & Santos, S. F. (2019) · Ceramics International · doi:10.1016/j.ceramint.2019.06.114 · Cited by 698
Holmberg, K., & Erdemir, A. (2019) · Tribology International · doi:10.1016/j.triboint.2019.03.024 · Cited by 677
Self-citationRecent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications
Zhai, W., Bai, L., Zhou, R., Fan, X., Kang, G., Liu, Y., & Zhou, K. (2021) · Advanced Science · doi:10.1002/advs.202003739 · Cited by 651
Solid Lubrication with MoS2: A Review
Vazirisereshk, M. R., Martini, A., Strubbe, D. A., & Baykara, M. Z. (2019) · Lubricants · doi:10.3390/lubricants7070057 · Cited by 605
Upcycling Single-Use Polyethylene into High-Quality Liquid Products
Celik, G., Kennedy, R. M., Hackler, R. A., Ferrandon, M., Tennakoon, A., Patnaik, S., LaPointe, A. M., Ammal, S. C., Heyden, A., Perras, F. A., et al. (2019) · ACS Central Science · doi:10.1021/acscentsci.9b00722 · Cited by 561
Metadata
- Authors
- Holmberg, K., & Erdemir, A.
- Venue
- Friction
- Publisher
- Tsinghua University Press
- Published
- 2017-09
- Volume
- 5
- Issue
- 3
- Pages
- 263-284
- ISSN
- 2223-7690 (ISSN-L)
- 2223-7704
- OpenAlex
- W2750857672
- Cited by
- 2,190
- References
- 29
- FWCI
- 70.89
- Type
- journal article
- Language
- en
- Open access
- diamond
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.