The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
A micro-indentation study of superplasticity in Pb, Sn, and Sn-38 wt% Pb
Open accessAbstract
In this study a method is developed for accurately determining strain rate sensitivities on a submicron scale using an indentation technique. The technique has been developed for use with the Nanoindenter and is applied to pure Pb, pure Pb, pure Sn, and Sn-38% Pb to elucidate the mechanisms responsible for Sn-38% Pb's superplastic behavior. In particular, it has been possible to vary the grain size with respect to the indentation size and thereby obtain strain rate sensitivity values for the interiors of individual grains (behavior of the lattice only) as well as for multiple grains (lattice + grain boundary, i.e. polycrystalline behavior). The results establish the role of grain boundaries in promoting high rate sensitivity and superplasticity. However, the results also indicate that the increase of rate sensitivity in the presence of boundaries is not due to grain boundary sliding. Grain boundary sliding has been consistently observed during the testing of superplastic Sn-38 wt% Pb, but only in the initial stages of deformation. A core-mantle model of superplastic deformation is suggested instead to account for the role of grain boundaries in enhancing strain rate sensitivity. Nous proposons dans cet article une méthode pour déterminer avec précision les sensibilités à la vitesse de déformation, à une échelle inférieure au μm, à l'aide d'une technique d'indentation. Nous avons développé cette technique pour qu'elle soit utilisable avec le Nano-indenteur, et nous l'avons appliquée au plomb pur, à l'étain pur, et à l'alliage d'étain à 38% en poids de plomb, dans le but d'élucider les mécanismes responsables de la superplasticité de Sn-38% Pb. Nous avons pu en particulier faire varier la taille des grains en fonction de la dimension de l'indentation, et obtenir ainsi des valeurs de la sensibilitéà la vitesse de déformation pour l'intérieur des grains individuels (comportement de réseau seul) ainsi que pour des groupes de grains (compartement de réseau seul) ainsi que pour des groupes de grains comportement de réseau + joint de grains, c'est-à-dire comportement polycristallin). Les résultats montrent que les joints de grains favorisent une forte sensibilité à la vitesse ainsi que la superplasticité. Cependant, ils indiquent aussi que l'accroissement de la sensibilité à la vitesse en présence des joints n'est pas dû au glissement intergranulaire. Nous avons effectivement observé du glissement intergranulaire au cours de la déformation de l'étain à 38% en poids de plomb, mais uniquement pendant les premiers stades de cette déformation. Nous suggérons un modèle de déformation superplastique avec un coeur entouré d'un manteau pour rendre compte du rôle des joints de grains dans l'augmentation de la sensibilité à la vitesse de déformation. Eine Methode wird entwickelt, mit der auf der Grundlage von Stempeleindrücken die Dehnungsratenempfindlichkeit im Submikron Maßstab gemessen werden kann. Diese Methode wird auf reines Blei, reines Zinn und Sn-38% Gew.-% Pb angewendet, um den für das superplastische Verhalten des Sn-38% Pb verantwortlichen Mechanismus aufzuklären. Insbesondere war es möglich, die Korngröbe im Vergleich zur Stempelgröße zu variieren und damit die Dehnungsratenempfindlichkeit im Inneren einzelner Körner (Verhalten des Kristallgitters) und für viele Körner (polykristallines Verhalten) zu messen. Diese Ergebnisse liefern den Einfluß der Korngrenzen bei der hohen Dehnungsratenempfindlichkeit und bei der Superplastizität. Allerdings zeigen die Ergebnisse auch, daß der Anstieg der Dehnungsratenempfindlichkeit bei Anwesenheit der Korngrenzen nicht auf Korngrenzgleitung zurückgeht. Korngrenzgleitung wurde während der Versuche am superplastischen Sn-38% Pb durchgehend beobachtet, jedoch nur zu Anfang der Verformung. Ein Kern-Mantelmodell der superplastischen Verformung wird damit nahegelegt, um die Rolle der Korngrenzen bei der Verstärkung der Dehnungsratenempfindlichkeit zu erklären.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A method for interpreting the data from depth-sensing indentation instruments
Doerner, M. F., & Nix, W. D. (1986) · Journal of Materials Research · doi:10.1557/jmr.1986.0601 · Cited by 2,863
Self-citation
Cited by
Mechanical properties of thin films
Nix, W. D. (1989) · Metallurgical Transactions A · doi:10.1007/bf02666659 · Cited by 2,546
Self-citationScaling, dimensional analysis, and indentation measurements
Cheng, Y.-T., & Cheng, C.-M. (2004) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2004.05.001 · Cited by 1,061
Measurement of Thin Film Mechanical Properties Using Nanoindentation
Pharr, G. M., & Oliver, W. C. (1992) · MRS Bulletin · doi:10.1557/s0883769400041634 · Cited by 1,012
High strain rate deformation of layered nanocomposites
Lee, J.-H., Veysset, D., Singer, J. P., Retsch, M., Saini, G., Pezeril, T., Nelson, K. A., & Thomas, E. L. (2012) · Nature Communications · doi:10.1038/ncomms2166 · Cited by 239
Metadata
- Authors
- Mayo, M. J., & Nix, W. D.
- Venue
- Acta Metallurgica
- Publisher
- Elsevier BV
- Published
- 1988-08
- Volume
- 36
- Issue
- 8
- Pages
- 2183-2192
- ISSN
- 0001-6160 (ISSN-L)
- OpenAlex
- W1988319387
- Cited by
- 439
- References
- 1
- FWCI
- 2.59
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A micro-indentation study of superplasticity in Pb, Sn, and Sn-38 wt% Pb. https://app.cochat.ai/papers/10.1016/0001-6160(88)90319-7
- The paper
- Mayo, M. J., & Nix, W. D. (1988). A micro-indentation study of superplasticity in Pb, Sn, and Sn-38 wt% Pb. Acta Metallurgica. https://doi.org/10.1016/0001-6160(88)90319-7
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.