The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index.
Fluid and particle dynamics in laser powder bed fusion
Open accessAbstract
In this work, we employ a combination of high-speed imaging and schlieren imaging, as well as multiphysics modelling, to elucidate the effects of the interaction between the laser beam and the powder bed. The formation of denuded areas where the powder was removed during single line and island scans over several layers were imaged for the first time. The inclination of the laser plume was shifted from forwards to backwards by changing power and scan speed, resulting in different denudation regimes with implications to the heat, mass and momentum transfer of the process. As the build progressed, denudation became less severe than for a single powder layer, but the occurrence of sintered and fused powder agglomerates, which were affected by the plume, increased. Schlieren imaging enabled the visualisation of the Ar gas flow, which takes place in the atmosphere above the bed due to the plume, in addition to its interaction with affected particles. Numerical modelling was used to understand and quantify the observed flow behaviour, through the hydrodynamic treatment of the laser plume as a multi-component Ar-Fe plasma. These results promote the characterisation of fluid dynamic phenomena during the laser powder-bed fusion (LPBF) process, which constitutes a key factor in the prevention of defects in additively manufactured parts.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Qiu, C., Panwisawas, C., Ward, R., Basoalto, H., Brooks, J. W., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.004 · Cited by 1,041
Self-citationDenudation of metal powder layers in laser powder bed fusion processes
Matthews, M. J., Guss, G., Khairallah, S. A., Rubenchik, A. M., Depond, P. J., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.05.017 · Cited by 809
Zhao, C., Fezzaa, K., Cunningham, R. W., Wen, H., De Carlo, F., Chen, L., Rollett, A. D., & Sun, T. (2017) · Scientific Reports · doi:10.1038/s41598-017-03761-2 · Cited by 758
Ly, S., Rubenchik, A. M., Khairallah, S. A., Guss, G. M., & Matthews, M. J. (2017) · Scientific Reports · doi:10.1038/s41598-017-04237-z · Cited by 521
Calculation of laser absorption by metal powders in additive manufacturing
Boley, C. D., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Optics · doi:10.1364/ao.54.002477 · Cited by 371
Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., Ashcroft, I., Wildman, R. D., & Hague, R. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2882-8 · Cited by 342
Heat and mass transfer in gas metal arc welding. Part I: The arc
Hu, J., & Tsai, H.-L. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2006.08.025 · Cited by 322
The effects of metal vapour in arc welding
Murphy, A. B. (2010) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/43/43/434001 · Cited by 319
Modeling the interaction of laser radiation with powder bed at selective laser melting
Gusarov, A. V., & Smurov, I. Y. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.065 · Cited by 284
Murphy, A. B., Tanaka, M., Yamamoto, K., Tashiro, S., Sato, T., & Lowke, J. J. (2009) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/42/19/194006 · Cited by 233
Grasso, M., Laguzza, V., Semeraro, Q., & Colosimo, B. M. (2017) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4034715 · Cited by 224
Fabbro, R., Slimani, S., Doudet, I., Coste, F., & Briand, F. (2006) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/39/2/023 · Cited by 199
An open-architecture metal powder bed fusion system for in-situ process measurements
Bidare, P., Maier, R. R. J., Beck, R. J., Shephard, J. D., & Moore, A. J. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.06.007 · Cited by 91
Self-citationVisualisation of alternating shielding gas flow in GTAW
Bitharas, I., Campbell, S. W., Galloway, A. M., et al. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.11.085 · Cited by 23
Self-citation
Cited by
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing
Leung, C. L. A., Marussi, S., Atwood, R. C., Towrie, M., Withers, P. J., & Lee, P. D. (2018) · Nature Communications · doi:10.1038/s41467-018-03734-7 · Cited by 817
Vafadar, A., Guzzomi, F., Rassau, A., & Hayward, K. (2021) · Applied Sciences · doi:10.3390/app11031213 · Cited by 748
Dynamics of pore formation during laser powder bed fusion additive manufacturing
Martin, A. A., Calta, N. P., Khairallah, S. A., Wang, J., Depond, P. J., Fong, A. Y., Thampy, V., Guss, G. M., Kiss, A. M., Stone, K. H., et al. (2019) · Nature Communications · doi:10.1038/s41467-019-10009-2 · Cited by 711
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Metadata
- Authors
- Bidare, P., Bitharas, I., Ward, R. M., Attallah, M. M., & Moore, A. J.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2018-01
- Volume
- 142
- Pages
- 107-120
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2759766116
- Cited by
- 555
- References
- 17
- FWCI
- 33.33
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.