The DOI matches its Crossref record; 4 of the 4 references it cites were found in a registry or an index.
Development and quantitative characterization of the precursor rheology of hyaluronic acid hydrogels for bioprinting
Open accessAbstract
Bioprinting technologies have tremendous potential for advancing regenerative medicine due to the precise spatial control over depositing a printable biomaterial, or bioink. Despite the growing interest in bioprinting, the field is challenged with developing biomaterials for extrusion-based bioprinting. The paradigm of contemporary bioink studies relies on trial-and-error methods for discovering printable biomaterials, which has little practical use for others who endeavor to develop bioinks. There is pressing need to follow the precedent set by a few pioneering studies that have attempted to standardize bioink characterizations for determining the properties that define printability. Here, we developed a pentenoate-functionalized hyaluronic acid hydrogel (PHA) into a printable bioink and used three recommended, quantitative rheological assessments to characterize the printability: 1) yield stress, 2) viscosity, and 3) storage modulus recovery. The most important characteristic is the yield stress; we found a yield stress upper limit of ~1000 Pa for PHA. Measuring the viscosity was advantageous for determining shear-thinning behavior, which aided in extruding highly viscous PHA through a nozzle. Post-printing recovery is required to maintain shape fidelity and we found storage modulus recoveries above ~85% were sufficient for PHA. Two formulations had superior printability (i.e., 1.5 MDa PHA − 4 wt%, and 1 MDa PHA − 8 wt%), and increasing cell concentrations in PHA up to 9 × 106 cells/mL had minimal effects on the printability. Even so, other factors such as sterilization and peptide modifications to enhance bioactivity may influence printability, highlighting the need for investigators to consider such factors when developing new bioinks.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
25th Anniversary Article: Engineering Hydrogels for Biofabrication
Malda, J., Visser, J., Melchels, F. P., Jüngst, T., Hennink, W. E., Dhert, W. J. A., Groll, J., & Hutmacher, D. W. (2013) · Advanced Materials · doi:10.1002/adma.201302042 · Cited by 1,901
Billiet, T., Gevaert, E., De Schryver, T., Cornelissen, M., & Dubruel, P. (2014) · Biomaterials · doi:10.1016/j.biomaterials.2013.09.078 · Cited by 1,015
Beck, E. C., Barragan, M., Tadros, M. H., Gehrke, S. H., & Detamore, M. S. (2016) · Acta Biomaterialia · doi:10.1016/j.actbio.2016.04.019 · Cited by 222
Self-citationBioprinting Cellularized Constructs Using a Tissue-specific Hydrogel Bioink
Skardal, A., Devarasetty, M., Kang, H.-W., Seol, Y.-J., Forsythe, S. D., Bishop, C., Shupe, T., Soker, S., & Atala, A. (2016) · Journal of Visualized Experiments · doi:10.3791/53606 · Cited by 65
Cited by
Printability and shape fidelity of bioinks in 3D bioprinting
Schwab, A., Levato, R., D’Este, M., Piluso, S., Eglin, D., & Malda, J. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00084 · Cited by 1,359
Antich, C., de Vicente, J., Jiménez, G., Chocarro, C., Carrillo, E., Montañez, E., Gálvez-Martín, P., & Marchal, J. A. (2020) · Acta Biomaterialia · doi:10.1016/j.actbio.2020.01.046 · Cited by 353
Polymeric Systems for Bioprinting
Bedell, M. L., Navara, A. M., Du, Y., Zhang, S., & Mikos, A. G. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00834 · Cited by 258
Physical and Chemical Factors Influencing the Printability of Hydrogel-based Extrusion Bioinks
Lee, S. C., Gillispie, G., Prim, P., & Lee, S. J. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00015 · Cited by 255
Metadata
- Authors
- Kiyotake, E. A., Douglas, A. W., Thomas, E. E., Nimmo, S. L., & Detamore, M. S.
- Venue
- Acta Biomaterialia
- Publisher
- Elsevier BV
- Published
- 2019-09
- Volume
- 95
- Pages
- 176-187
- ISSN
- 1742-7061 (ISSN-L)
- OpenAlex
- W2910090532
- Cited by
- 166
- References
- 4
- FWCI
- 7.21
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.