An investigation into 3D printing of fibre reinforced thermoplastic composites
Open accessThe DOI matches its Crossref record; 27 of the 27 references it cites were found in a registry or an index.
Abstract
Fused filament fabrication (FFF) is a 3D printing technique which allows layer-by-layer build-up of a part by the deposition of thermoplastic material through a nozzle. The technique allows for complex shapes to be made with a degree of design freedom unachievable with traditional manufacturing methods. However, the mechanical properties of the thermoplastic materials used are low compared to common engineering materials. In this work, composite 3D printing feedstocks for FFF are investigated, wherein carbon fibres are embedded into a thermoplastic matrix to increase strength and stiffness. First, the key processing parameters for FFF are reviewed, showing how fibres alter the printing dynamics by changing the viscosity and the thermal profile of the printed material. The state-of-the-art in composite 3D printing is presented, showing a distinction between short fibre feedstocks versus continuous fibre feedstocks. An experimental study was performed to benchmark these two methods. It is found that printing of continuous carbon fibres using the MarkOne printer gives significant increases in performance over unreinforced thermoplastics, with mechanical properties in the same order of magnitude of typical unidirectional epoxy matrix composites. The method, however, is limited in design freedom as the brittle continuous carbon fibres cannot be deposited freely through small steering radii and sharp angles. Filaments with embedded short carbon microfibres (∼100 μm) show better print capabilities and are suitable for use with standard printing methods, but only offer a slight increase in mechanical properties over the pure thermoplastic properties. It is hypothesized that increasing the fibre length in short fibre filament is expected to lead to increased mechanical properties, potentially approaching those of continuous fibre composites, whilst keeping the high degree of design freedom of the FFF process.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Anisotropic material properties of fused deposition modeling ABS
Ahn, S., Montero, M., Odell, D., Roundy, S., & Wright, P. K. (2002) · Rapid Prototyping Journal · doi:10.1108/13552540210441166 · Cited by 2,382
Ning, F., Cong, W., Qiu, J., Wei, J., & Wang, S. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.06.013 · Cited by 1,718
Highly oriented carbon fiber–polymer composites via additive manufacturing
Tekinalp, H. L., Kunc, V., Velez-Garcia, G. M., Duty, C. E., Love, L. J., Naskar, A. K., Blue, C. A., & Ozcan, S. (2014) · Composites Science and Technology · doi:10.1016/j.compscitech.2014.10.009 · Cited by 1,514
A review of melt extrusion additive manufacturing processes: I. Process design and modeling
N. Turner, B., Strong, R., & A. Gold, S. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-01-2013-0012 · Cited by 1,450
Effect of processing conditions on the bonding quality of FDM polymer filaments
Sun, Q., Rizvi, G. M., Bellehumeur, C. T., & Gu, P. (2008) · Rapid Prototyping Journal · doi:10.1108/13552540810862028 · Cited by 1,277
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Matsuzaki, R., Ueda, M., Namiki, M., Jeong, T.-K., Asahara, H., Horiguchi, K., Nakamura, T., Todoroki, A., & Hirano, Y. (2016) · Scientific Reports · doi:10.1038/srep23058 · Cited by 1,171
Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., & Zhao, J. (2015) · Materials · doi:10.3390/ma8095271 · Cited by 881
Fu, S. (1996) · Composites Science and Technology · doi:10.1016/s0266-3538(96)00072-3 · Cited by 847
Turner, B. N., & Gold, S. A. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-02-2013-0017 · Cited by 770
Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process
Bellehumeur, C., Li, L., Sun, Q., & Gu, P. (2004) · Journal of Manufacturing Processes · doi:10.1016/s1526-6125(04)70071-7 · Cited by 768
Lanzotti, A., Grasso, M., Staiano, G., & Martorelli, M. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2014-0135 · Cited by 684
3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance
Yang, C., Tian, X., Liu, T., Cao, Y., & Li, D. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-08-2015-0098 · Cited by 515
Introduction to Aerospace Materials
Mouritz, A. (2012) · American Institute of Aeronautics and Astronautics eBooks · doi:10.2514/4.869198 · Cited by 511
Nanofiber‐reinforced polymers prepared by fused deposition modeling
Shofner, M. L., Lozano, K., Rodríguez‐Macías, F. J., & Barrera, E. V. (2003) · Journal of Applied Polymer Science · doi:10.1002/app.12496 · Cited by 484
Hwang, S., Reyes, E. I., Moon, K.-S., Rumpf, R. C., & Kim, N. S. (2015) · Journal of Electronic Materials · doi:10.1007/s11664-014-3425-6 · Cited by 482
Lewicki, J. P., Rodriguez, J. N., Zhu, C., Worsley, M. A., Wu, A. S., Kanarska, Y., Horn, J. D., Duoss, E. B., Ortega, J. M., Elmer, W., et al. (2017) · Scientific Reports · doi:10.1038/srep43401 · Cited by 318
Composite Modeling and Analysis for Fabrication of FDM Prototypes with Locally Controlled Properties
Li, L., Sun, Q., Bellehumeur, C. T., & Gu, P. (2002) · Journal of Manufacturing Processes · doi:10.1016/s1526-6125(02)70139-4 · Cited by 306
Christiyan, K. G. J., Chandrasekhar, U., & Venkateswarlu, K. (2016) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/114/1/012109 · Cited by 302
Recent developments in 3D printable composite materials
Kalsoom, U., Nesterenko, P. N., & Paull, B. (2016) · RSC Advances · doi:10.1039/c6ra11334f · Cited by 294
Modification of Frenkel's model for sintering
Pokluda, O., Bellehumeur, C. T., & Vlachopoulos, J. (1997) · AIChE Journal · doi:10.1002/aic.690431213 · Cited by 281
Characterization of the mesostructure of fused‐deposition acrylonitrile‐butadiene‐styrene materials
Rodriguez, J. F., Thomas, J. P., & Renaud, J. E. (2000) · Rapid Prototyping Journal · doi:10.1108/13552540010337056 · Cited by 226
Raster angle mechanics in fused deposition modelling
Huang, B., & Singamneni, S. (2014) · Journal of Composite Materials · doi:10.1177/0021998313519153 · Cited by 163
Strengthening of 3D Printed Fused Deposition Manufactured Parts Using the Fill Compositing Technique
Belter, J. T., & Dollar, A. M. (2015) · PLoS ONE · doi:10.1371/journal.pone.0122915 · Cited by 157
Valentin, D., Paray, F., & Guetta, B. (1987) · Journal of Materials Science · doi:10.1007/bf01160550 · Cited by 126
The Relationship between Tensile and Flexural Strength of Unidirectional Composites
Wisnom, M. R. (1992) · Journal of Composite Materials · doi:10.1177/002199839202600805 · Cited by 109
Bellini, A., & Güçeri, S. İ. (2002) · doi:10.17918/etd-22 · Cited by 76
Cited by
A critical review on the fused deposition modeling of thermoplastic polymer composites
Penumakala, P. K., Santo, J., & Thomas, A. (2020) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2020.108336 · Cited by 704
Kabir, S. M. F., Mathur, K., & Seyam, A.-F. M. (2020) · Composite Structures · doi:10.1016/j.compstruct.2019.111476 · Cited by 678
Multi‐Material 3D and 4D Printing: A Survey
Rafiee, M., Farahani, R. D., & Therriault, D. (2020) · Advanced Science · doi:10.1002/advs.201902307 · Cited by 662
Mechanical characterization of FDM 3D printing of continuous carbon fiber reinforced PLA composites
Heidari-Rarani, M., Rafiee-Afarani, M., & Zahedi, A. M. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107147 · Cited by 615
Daminabo, S. C., Goel, S., Grammatikos, S. A., Nezhad, H. Y., & Thakur, V. K. (2020) · Materials Today Chemistry · doi:10.1016/j.mtchem.2020.100248 · Cited by 567
Metadata
- Authors
- Blok, L. G., Longana, M. L., Yu, H., & Woods, B. K. S.
- Venue
- Additive Manufacturing
- Publisher
- Elsevier BV
- Published
- 2018-08
- Volume
- 22
- Pages
- 176-186
- ISSN
- 2214-7810 (ISSN-L)
- 2214-8604
- OpenAlex
- W2800333761
- Cited by
- 866
- References
- 27
- FWCI
- 41.91
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.