The DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index.
In situ absorptivity measurements of metallic powders during laser powder-bed fusion additive manufacturing
Open accessAbstract
The effective absorptivity of continuous wave 1070 nm laser light has been studied for bare and metal powder-coated discs of 316L stainless steel as well as for aluminum alloy 1100 and tungsten by use of direct calorimetric measurements. After carefully validating the applicability of the method, the effective absorptivity is plotted as a function of incident laser power from 30 up to ≈540 W for scanning speeds of 100, 500 and 1500 mm s−1. The effective absorptivity versus power curves of the bulk materials typically show a slight change in effective absorptivity from 30 W until the onset of the formation of a recoil pressure-induced surface depression. As observed using high-speed video, this change in surface morphology leads to an increase in absorption of the laser light. At the higher powers beyond the keyhole transition, a saturation value is reached for both bare discs and powder-coated disks. For ≈100 μm thick powder layers, the measured absorptivity was found to be two times that of the bare polished discs for low-laser power. There is a sharp decrease when full melting of the powder tracks is achieved, followed by a keyhole-driven increase at higher powers, similar to the bare disc case. It is shown that, under conditions associated with laser powder-bed fusion additive manufacturing, absorptivity values can vary greatly, and differ from both powder-layer measurements and liquid metal estimates from the literature.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
Self-citationLaser Processing and Chemistry
Bäuerle, D. (1996) · Springer eBooks · doi:10.1007/978-3-662-03253-4 · Cited by 2,196
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Self-citationRecommended Values of Thermophysical Properties for Selected Commercial Alloys
Mills, K. C. (2002) · Woodhead Publishing Limited eBooks · doi:10.1533/9781845690144 · Cited by 1,444
King, W. E., Anderson, A. T., Ferencz, R. M., Hodge, N. E., Kamath, C., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Physics Reviews · doi:10.1063/1.4937809 · Cited by 1,258
Self-citationLaser Processing and Chemistry
Bäuerle, D. (2011) · Springer eBooks · doi:10.1007/978-3-642-17613-5 · Cited by 843
Denudation of metal powder layers in laser powder bed fusion processes
Matthews, M. J., Guss, G., Khairallah, S. A., Rubenchik, A. M., Depond, P. J., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.05.017 · Cited by 809
Self-citation(2013) · Medical Entomology and Zoology · Cited by 690
Ly, S., Rubenchik, A. M., Khairallah, S. A., Guss, G. M., & Matthews, M. J. (2017) · Scientific Reports · doi:10.1038/s41598-017-04237-z · Cited by 521
Self-citationAbsorptance of powder materials suitable for laser sintering
Tolochko, N. K., Khlopkov, Y. V., Mozzharov, S. E., Ignatiev, M. B., Laoui, T., & Titov, V. I. (2000) · Rapid Prototyping Journal · doi:10.1108/13552540010337029 · Cited by 518
Cited by
Material-structure-performance integrated laser-metal additive manufacturing
Gu, D., Shi, X., Poprawe, R., Bourell, D. L., Setchi, R., & Zhu, J. (2021) · Science · doi:10.1126/science.abg1487 · Cited by 1,703
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed x-ray imaging
Cunningham, R., Zhao, C., Parab, N., Kantzos, C., Pauza, J., Fezzaa, K., Sun, T., & Rollett, A. D. (2019) · Science · doi:10.1126/science.aav4687 · Cited by 1,066
Dynamics of pore formation during laser powder bed fusion additive manufacturing
Martin, A. A., Calta, N. P., Khairallah, S. A., Wang, J., Depond, P. J., Fong, A. Y., Thampy, V., Guss, G. M., Kiss, A. M., Stone, K. H., et al. (2019) · Nature Communications · doi:10.1038/s41467-019-10009-2 · Cited by 711
Self-citationControlling interdependent meso-nanosecond dynamics and defect generation in metal 3D printing
Khairallah, S. A., Martin, A. A., Lee, J. R. I., Guss, G., Calta, N. P., Hammons, J. A., Nielsen, M. H., Chaput, K., Schwalbach, E., Shah, M. N., et al. (2020) · Science · doi:10.1126/science.aay7830 · Cited by 506
Self-citation
Metadata
- Authors
- Trapp, J., Rubenchik, A. M., Guss, G., & Matthews, M. J.
- Venue
- Applied Materials Today
- Publisher
- Elsevier BV
- Published
- 2017-12
- Volume
- 9
- Pages
- 341-349
- ISSN
- 2352-9407 (ISSN-L)
- OpenAlex
- W2755097489
- Cited by
- 509
- References
- 19
- FWCI
- 28.27
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: In situ absorptivity measurements of metallic powders during laser powder-bed fusion additive manufacturing. https://app.cochat.ai/papers/10.1016/j.apmt.2017.08.006
- The paper
- Trapp, J., Rubenchik, A. M., Guss, G., & Matthews, M. J. (2017). In situ absorptivity measurements of metallic powders during laser powder-bed fusion additive manufacturing. Applied Materials Today. https://doi.org/10.1016/j.apmt.2017.08.006
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.