The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
The preparation of ZrO2-Al2O3 composite ceramic by SLA-3D printing and sintering processing
Abstract
In this paper, the UV curable ZrO2-Al2O3 composite ceramic pastes based on SLA-3D printing technology were synthetized firstly, and the corresponding ceramic green bodies were 3D printed, and finally the ZrO2-Al2O3 composite ceramic parts were manufactured by a subsequent debinding and sintering process. Our work focuses on the investigation of the microstructure, hardness and fracture toughness of the printed ZrO2-Al2O3 composite ceramics sintered at different maximum sintering temperature and holding time. In case of the sintering temperature of 1500 °C and holding time of 60 min, the actual density, hardness and fracture toughness of the ceramics can reach 3.75 g/cm3, 14.1 GPa and 4.05 MPa m1/2, respectively. If the sintering temperature is higher than 1500 °C, the abnormal grain growth can occur, resulting in some more reductions in the mechanical properties of ceramics; while when the sintering temperature is lower than 1500 °C, the lower driving force makes the grains not fully developed, resulting in a low density of ceramics and worse mechanical properties. With the increase of holding time, the sintering driving force is promoted, making for the grain growth. However, when holding time is more than 60 min, the actual density of ceramics almost remains unchanged, and the mechanical properties of ceramics are not able to be improved further.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Ding, S., Zou, B., Wang, P., & Ding, H. (2019) · Polymer Testing · doi:10.1016/j.polymertesting.2019.105948 · Cited by 351
Self-citation
Cited by
Additive Manufacturing of Polymer Materials: Progress, Promise and Challenges
Saleh Alghamdi, S., John, S., Roy Choudhury, N., & Dutta, N. K. (2021) · Polymers · doi:10.3390/polym13050753 · Cited by 469
WANG, P., ZOU, B., DING, S., LI, L., & HUANG, C. (2021) · Chinese Journal of Aeronautics · doi:10.1016/j.cja.2020.05.040 · Cited by 365
Self-citationProgress and challenges towards additive manufacturing of SiC ceramic
He, R., Zhou, N., Zhang, K., Zhang, X., Zhang, L., Wang, W., & Fang, D. (2021) · Journal of Advanced Ceramics · doi:10.1007/s40145-021-0484-z · Cited by 327
Camargo, I. L. D., Morais, M. M., Fortulan, C. A., & Branciforti, M. C. (2021) · Ceramics International · doi:10.1016/j.ceramint.2021.01.031 · Cited by 263
Metadata
- Authors
- Liu, X., Zou, B., Xing, H., & Huang, C.
- Venue
- Ceramics International
- Publisher
- Elsevier BV
- Published
- 2020-01
- Volume
- 46
- Issue
- 1
- Pages
- 937-944
- ISSN
- 0272-8842 (ISSN-L)
- OpenAlex
- W2971949262
- Cited by
- 201
- References
- 1
- FWCI
- 10.30
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The preparation of ZrO2-Al2O3 composite ceramic by SLA-3D printing and sintering processing. https://app.cochat.ai/papers/10.1016/j.ceramint.2019.09.054
- The paper
- Liu, X., Zou, B., Xing, H., & Huang, C. (2020). The preparation of ZrO2-Al2O3 composite ceramic by SLA-3D printing and sintering processing. Ceramics International. https://doi.org/10.1016/j.ceramint.2019.09.054
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.