The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.
Experimental and kinetic modeling investigation on the laminar flame propagation of ammonia under oxygen enrichment and elevated pressure conditions
Abstract
Abstract Ammonia is attracting more and more attentions due to its role as both a carbon-free fuel for gas turbines and an effective H2 carrier. Only a limit number of investigations on the laminar flame propagation and laminar burning velocity of ammonia have been performed on elevated pressures, which were focused on ammonia/air mixtures and suffered strong buoyancy effect. In this work, laminar flame propagation of ammonia/O2/N2 mixtures covering wide ranges of equivalence ratios, oxygen contents and initial pressures was investigated in a high-pressure constant-volume cylindrical combustion vessel. The oxygen enrichment speeds up the spherically expanding flames and consequently reduces buoyancy effect on the laminar flame propagation of ammonia. The laminar burning velocity was observed to increase with the increasing oxygen content, but decrease with the increasing initial pressure. A kinetic model of ammonia combustion consisting 38 species and 265 reactions was constructed from previous models with updated rate constants of important reactions. The present model can reasonably reproduce the laminar burning velocity data in this work and literature, as well as the ignition delay time and speciation data in literature. Based on the model analysis, effects of oxygen enrichment, equivalence ratio and initial pressure on laminar burning velocities of ammonia were analyzed in detail. It is revealed that the enhanced flame propagation with oxygen enrichment is mainly due to the increase of adiabatic flame temperature which in turn leads to higher concentrations of key radicals like H, OH and NH2. For NH3 and its major decomposition products like NH2 and NH, reactions with oxygenated species such as OH, O, O2 and NO are generally more important in the lean flames, while the role of reactions with H, NH and NH2 becomes crucial in the rich flames. The calculated pressure dependent coefficient indicates that NH3/O2/N2 flames exhibit clear pressure dependence, while this pressure dependence is weaker than those of the hydrocarbon and biofuel flames.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Mechanism and modeling of nitrogen chemistry in combustion
Miller, J. A., & Bowman, C. T. (1989) · Progress in Energy and Combustion Science · doi:10.1016/0360-1285(89)90017-8 · Cited by 3,172
Science and technology of ammonia combustion
Kobayashi, H., Hayakawa, A., Somarathne, K. D. K. A., & Okafor, E. C. (2019) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2018.09.029 · Cited by 2,532
Modeling nitrogen chemistry in combustion
Glarborg, P., Miller, J. A., Ruscic, B., & Klippenstein, S. J. (2018) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2018.01.002 · Cited by 1,998
Evaluated Kinetic Data for Combustion Modeling. Supplement I
Baulch, D. L., Cobos, C. J., Cox, R. A., Frank, P., Hayman, G., Just, T., Kerr, J. A., Murrells, T., Pilling, M. J., Troe, J., et al. (1994) · Journal of Physical and Chemical Reference Data · doi:10.1063/1.555953 · Cited by 1,583
Evaluated Kinetic Data for Combustion Modeling: Supplement II
Baulch, D. L., Bowman, C. T., Cobos, C. J., Cox, R. A., Just, T., Kerr, J. A., Pilling, M. J., Stocker, D., Troe, J., Tsang, W., et al. (2005) · Journal of Physical and Chemical Reference Data · doi:10.1063/1.1748524 · Cited by 1,457
Experimental and numerical study of the laminar burning velocity of CH4–NH3–air premixed flames
Okafor, E. C., Naito, Y., Colson, S., Ichikawa, A., Kudo, T., Hayakawa, A., & Kobayashi, H. (2018) · Combustion and Flame · doi:10.1016/j.combustflame.2017.09.002 · Cited by 1,068
Ranzi, E., Frassoldati, A., Grana, R., et al. (2012) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2012.03.004 · Cited by 1,027
Using ammonia as a sustainable fuel
Zamfirescu, C., & Dincer, I. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.02.097 · Cited by 875
Han, X., Wang, Z., Costa, M., Sun, Z., He, Y., & Cen, K. (2019) · Combustion and Flame · doi:10.1016/j.combustflame.2019.05.003 · Cited by 869
Laminar burning velocity and Markstein length of ammonia/air premixed flames at various pressures
Hayakawa, A., Goto, T., Mimoto, R., Arakawa, Y., Kudo, T., & Kobayashi, H. (2015) · Fuel · doi:10.1016/j.fuel.2015.06.070 · Cited by 854
Mathieu, O., & Petersen, E. L. (2015) · Combustion and Flame · doi:10.1016/j.combustflame.2014.08.022 · Cited by 768
Turbulent premixed combustion: Flamelet structure and its effect on turbulent burning velocities
DRISCOLL, J. (2007) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2007.04.002 · Cited by 765
Implementation of the NCN pathway of prompt-NO formation in the detailed reaction mechanism
Konnov, A. A. (2009) · Combustion and Flame · doi:10.1016/j.combustflame.2009.03.016 · Cited by 689
Bradley, D. (1996) · Combustion and Flame · doi:10.1016/0010-2180(95)00115-8 · Cited by 653
An experimental and kinetic modeling study of premixed NH3/CH4/O2/Ar flames at low pressure
Tian, Z., Li, Y., Zhang, L., Glarborg, P., & Qi, F. (2009) · Combustion and Flame · doi:10.1016/j.combustflame.2009.03.005 · Cited by 635
Self-citationOkafor, E. C., Naito, Y., Colson, S., Ichikawa, A., Kudo, T., Hayakawa, A., & Kobayashi, H. (2019) · Combustion and Flame · doi:10.1016/j.combustflame.2019.03.008 · Cited by 593
Ichikawa, A., Hayakawa, A., Kitagawa, Y., Kunkuma Amila Somarathne, K. D., Kudo, T., & Kobayashi, H. (2015) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2015.04.024 · Cited by 540
Gas-Phase Combustion Chemistry
(2000) · Springer eBooks · doi:10.1007/978-1-4612-1310-9 · Cited by 519
Study on using hydrogen and ammonia as fuels: Combustion characteristics and NOxformation
Li, J., Huang, H., Kobayashi, N., He, Z., & Nagai, Y. (2014) · International Journal of Energy Research · doi:10.1002/er.3141 · Cited by 462
Shrestha, K. P., Seidel, L., Zeuch, T., & Mauss, F. (2018) · Energy & Fuels · doi:10.1021/acs.energyfuels.8b01056 · Cited by 441
Kinetic Modeling of the Oxidation of Ammonia in Flames
Miller, J. A., Smooke, M. D., Green, R. M., & Kee, R. J. (1983) · Combustion Science and Technology · doi:10.1080/00102208308923691 · Cited by 426
Flammability limits, ignition energy, and flame speeds in H2–CH4–NH3–N2O–O2–N2 mixtures
Pfahl, U. J., Ross, M. C., Shepherd, J. E., Pasamehmetoglu, K. O., & Unal, C. (2000) · Combustion and Flame · doi:10.1016/s0010-2180(00)00152-8 · Cited by 405
Nakamura, H., Hasegawa, S., & Tezuka, T. (2017) · Combustion and Flame · doi:10.1016/j.combustflame.2017.06.021 · Cited by 366
Studies on properties of laminar premixed hydrogen-added ammonia/air flames for hydrogen production
Lee, J. H., Kim, J. H., Park, J. H., & Kwon, O. C. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2009.11.071 · Cited by 360
Burning velocity measurements of nitrogen-containing compounds
Takizawa, K., Takahashi, A., Tokuhashi, K., Kondo, S., & Sekiya, A. (2008) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2007.11.089 · Cited by 345
Kumar, P., & Meyer, T. R. (2013) · Fuel · doi:10.1016/j.fuel.2012.06.103 · Cited by 314
Ammonia chemistry below 1400 K under fuel-rich conditions in a flow reactor
Skreiberg, Ø., Kilpinen, P., & Glarborg, P. (2004) · Combustion and Flame · doi:10.1016/j.combustflame.2003.12.008 · Cited by 310
Combustion Chemistry of Nitrogen
Dean, A. M., & Bozzelli, J. W. (2000) · Springer eBooks · doi:10.1007/978-1-4612-1310-9_2 · Cited by 303
Effect of Chemistry and Transport Properties on Near-Limit Flames at Microgravity
Ronney, P. D. (1988) · Combustion Science and Technology · doi:10.1080/00102208808947092 · Cited by 258
Detailed Kinetic Modelling of Chemistry and Temperature Effects on Ammonia Oxidation
LINDSTEDT, R. P., LOCKWOOD, F. C., & SELIM, M. A. (1994) · Combustion Science and Technology · doi:10.1080/00102209408935436 · Cited by 256
Effects of ammonia substitution on hydrogen/air flame propagation and emissions
Lee, J. H., Lee, S. I., & Kwon, O. C. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.07.104 · Cited by 252
Reactor technology options for distributed hydrogen generation via ammonia decomposition: A review
Chiuta, S., Everson, R. C., Neomagus, H. W. J. P., van der Gryp, P., & Bessarabov, D. (2013) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2013.09.067 · Cited by 235
Klippenstein, S. J., Harding, L. B., Ruscic, B., Sivaramakrishnan, R., Srinivasan, N. K., Su, M.-C., & Michael, J. V. (2009) · The Journal of Physical Chemistry A · doi:10.1021/jp905454k · Cited by 159
The characteristics of flame propagation in ammonia/oxygen mixtures
Liu, Q., Chen, X., Huang, J., et al. (2018) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2018.09.073 · Cited by 148
Zakaznov, V. F., Kursheva, L. A., & Fedina, Z. I. (1978) · Combustion Explosion and Shock Waves · doi:10.1007/bf00786097 · Cited by 147
Goldmann, A., & Dinkelacker, F. (2018) · Fuel · doi:10.1016/j.fuel.2018.03.030 · Cited by 129
Explosions of Syngas/CO2 Mixtures in Oxygen-Enriched Air
Salzano, E., Basco, A., Cammarota, F., Sarli, V. D., & Benedetto, A. D. (2011) · Industrial & Engineering Chemistry Research · doi:10.1021/ie201734u · Cited by 65
Samu, V., Varga, T., Rahinov, I., Cheskis, S., & Turányi, T. (2017) · Fuel · doi:10.1016/j.fuel.2017.10.019 · Cited by 51
Mackie, J. C., & Bacskay, G. B. (2005) · The Journal of Physical Chemistry A · doi:10.1021/jp0544585 · Cited by 43
Wang, G., Li, Y., Yuan, W., Wang, Y., Zhou, Z., Liu, Y., & Cai, J. (2018) · Combustion and Flame · doi:10.1016/j.combustflame.2018.01.025 · Cited by 38
Self-citationLinder, D. P., Duan, X. F., & Page, M. (1995) · The Journal of Physical Chemistry · doi:10.1021/j100029a025 · Cited by 37
Zheng, J., Rocha, R. J., Pelegrini, M., Ferrão, L. F. A., de Carvalho, E. F. V., Roberto‐Neto, O., Machado, F. B. C., & Truhlar, D. G. (2012) · The Journal of Chemical Physics · doi:10.1063/1.4707734 · Cited by 34
Cited by
Review on Ammonia as a Potential Fuel: From Synthesis to Economics
Valera-Medina, A., Amer-Hatem, F., Azad, A. K., Dedoussi, I. C., de Joannon, M., Fernandes, R. X., Glarborg, P., Hashemi, H., He, X., Mashruk, S., et al. (2021) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c03685 · Cited by 1,061
A review on ammonia, ammonia-hydrogen and ammonia-methane fuels
Chai, W. S., Bao, Y., Jin, P., Tang, G., & Zhou, L. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111254 · Cited by 1,028
An experimental, theoretical and kinetic-modeling study of the gas-phase oxidation of ammonia
Stagni, A., Cavallotti, C., Arunthanayothin, S., Song, Y., Herbinet, O., Battin-Leclerc, F., & Faravelli, T. (2020) · Reaction Chemistry & Engineering · doi:10.1039/c9re00429g · Cited by 742
Shrestha, K. P., Lhuillier, C., Barbosa, A. A., Brequigny, P., Contino, F., Mounaïm-Rousselle, C., Seidel, L., & Mauss, F. (2021) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2020.06.197 · Cited by 641
Review on the recent advances on ammonia combustion from the fundamentals to the applications
Elbaz, A. M., Wang, S., Guiberti, T. F., & Roberts, W. L. (2022) · Fuel Communications · doi:10.1016/j.jfueco.2022.100053 · Cited by 639
Metadata
- Authors
- Mei, B., Zhang, X., Ma, S., Cui, M., Guo, H., Cao, Z., & Li, Y.
- Venue
- Combustion and Flame
- Publisher
- Elsevier BV
- Published
- 2019-12
- Volume
- 210
- Pages
- 236-246
- ISSN
- 0010-2180 (ISSN-L)
- OpenAlex
- W2972204853
- Cited by
- 652
- References
- 42
- FWCI
- 19.20
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.