The DOI matches its Crossref record; 14 of the 14 references it cites were found in a registry or an index.
A review on the tensile properties of natural fiber reinforced polymer composites
Abstract
Abstract This paper is a review on the tensile properties of natural fiber reinforced polymer composites. Natural fibers have recently become attractive to researchers, engineers and scientists as an alternative reinforcement for fiber reinforced polymer (FRP) composites. Due to their low cost, fairly good mechanical properties, high specific strength, non-abrasive, eco-friendly and bio-degradability characteristics, they are exploited as a replacement for the conventional fiber, such as glass, aramid and carbon. The tensile properties of natural fiber reinforce polymers (both thermoplastics and thermosets) are mainly influenced by the interfacial adhesion between the matrix and the fibers. Several chemical modifications are employed to improve the interfacial matrix–fiber bonding resulting in the enhancement of tensile properties of the composites. In general, the tensile strengths of the natural fiber reinforced polymer composites increase with fiber content, up to a maximum or optimum value, the value will then drop. However, the Young’s modulus of the natural fiber reinforced polymer composites increase with increasing fiber loading. Khoathane et al. [1] found that the tensile strength and Young’s modulus of composites reinforced with bleached hemp fibers increased incredibly with increasing fiber loading. Mathematical modelling was also mentioned. It was discovered that the rule of mixture (ROM) predicted and experimental tensile strength of different natural fibers reinforced HDPE composites were very close to each other. Halpin–Tsai equation was found to be the most effective equation in predicting the Young’s modulus of composites containing different types of natural fibers.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Natural fibres: Can they replace glass in fibre reinforced plastics?
Wambua, P., Ivens, J., & Verpoest, I. (2003) · Composites Science and Technology · doi:10.1016/s0266-3538(03)00096-4 · Cited by 2,676
Natural fiber polymer composites: A review
Saheb, D. N., & Jog, J. P. (1999) · Advances in Polymer Technology · doi:10.1002/(sici)1098-2329(199924)18:4<351::aid-adv6>3.0.co;2-x · Cited by 2,429
Natural-fiber-reinforced polymer composites in automotive applications
Holbery, J., & Houston, D. (2006) · JOM · doi:10.1007/s11837-006-0234-2 · Cited by 1,565
Recent Development in Natural Fiber Reinforced Polypropylene Composites
Malkapuram, R., Kumar, V., & Negi, Y. S. (2009) · Journal of Reinforced Plastics and Composites · doi:10.1177/0731684407087759 · Cited by 813
Joseph, P. (1999) · Composites Science and Technology · doi:10.1016/s0266-3538(99)00024-x · Cited by 565
Studies on the properties of natural fibers-reinforced thermoplastic starch composites
Ma, X., Yu, J., & Kennedy, J. F. (2005) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2005.07.015 · Cited by 408
Liu, L., Yu, J., Cheng, L., & Qu, W. (2009) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2009.03.002 · Cited by 335
Hu, R., & Lim, J.-K. (2007) · Journal of Composite Materials · doi:10.1177/0021998306069878 · Cited by 334
Natural fiber-reinforced polymer composites
Taj, S. A., Khan, S., & Munawar, M. A. (2007) · Proceedings of the Pakistan Academy of Sciences · Cited by 287
Lee, B.-H., Kim, H.-J., & Yu, W.-R. (2009) · Fibers and Polymers · doi:10.1007/s12221-009-0083-z · Cited by 263
Predicting the tensile strength of natural fibre reinforced thermoplastics
Facca, A. G., Kortschot, M. T., & Yan, N. (2007) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.12.018 · Cited by 171
Development of HEMP Fiber Reinforced Polypropylene Composites
Hargitai, H., Rácz, I., & Anandjiwala, R. D. (2008) · Journal of Thermoplastic Composite Materials · doi:10.1177/0892705707083949 · Cited by 157
López-Manchado, M. Á., Arroyo, M., Biagiotti, J., & Kenny, J. M. (2003) · Journal of Applied Polymer Science · doi:10.1002/app.12866 · Cited by 120
Khoathane, M. C., Vorster, O. C., & Sadiku, E. R. (2008) · Journal of Reinforced Plastics and Composites · doi:10.1177/0731684407086325 · Cited by 108
Research works printed but not linked: 10
- Li, 2009, The influence of fiber content on properties of injection molded flax fiber-HDPE biocomposites, Can Biosyst Eng, 08–148, 1
- Ahmad, 2006, Effect of extrusion rate and fiber loading on mechanical properties of Twaron fiber-thermoplastic natural rubber (TPNR) composites, J Reinf Plast Compos, 25, 957, 10.1177/0731684406065082 · doi:10.1177/0731684406065082
- Facca, 2007, Predicting the elastic modulus of natural fiber reinforced thermoplastics, Compos: Part A: Appl Sci Manuf, 37, 1660, 10.1016/j.compositesa.2005.10.006 · doi:10.1016/j.compositesa.2005.10.006
- Li, 2009, A study on flax fiber-reinforced polyethylene biocomposites, Appl Eng Agr, 25, 525, 10.13031/2013.27454 · doi:10.13031/2013.27454
- Panigrahy, 2006, Overview of flax fibre reinforced thermoplastic composites, Can Biosyst Eng J, 06–165, 1
- Santos, 2009, Effectiveness of maleated- and salinized-PP for coir fiber-filled composites, J Reinf Plast Compos, 28, 2119, 10.1177/0731684408091704 · doi:10.1177/0731684408091704
- Tungjitpornkull, 2009, Processing technique and fibre orientation angle affecting the mechanical properties of E-glass reinforced wood/PVC composites, J Mater Process Technol, 209, 3079, 10.1016/j.jmatprotec.2008.07.021 · doi:10.1016/j.jmatprotec.2008.07.021
- Li, 2009, A study on flax fibre-reinforced polyethylene biocomposites by injection moulding, Appl Eng Agr, 25, 525, 10.13031/2013.27454 · doi:10.13031/2013.27454
- Medina, 2009, Process related mechanical properties of press molded natural fiber reinforced polymers, Compos Sci Technol, 69, 1404, 10.1016/j.compscitech.2008.09.017 · doi:10.1016/j.compscitech.2008.09.017
- Khondker, 2005, Fabrication and mechanical properties of unidirectional jute/PP composites using jute yarns by film stacking method, J Polym Environ, 13, 115, 10.1007/s10924-005-2943-y · doi:10.1007/s10924-005-2943-y
Cited by
Processing bulk natural wood into a high-performance structural material
Song, J., Chen, C., Zhu, S., Zhu, M., Dai, J., Ray, U., Li, Y., Kuang, Y., Li, Y., Quispe, N., et al. (2018) · Nature · doi:10.1038/nature25476 · Cited by 1,632
Recent advances in the development of aerospace materials
Zhang, X., Chen, Y., & Hu, J. (2018) · Progress in Aerospace Sciences · doi:10.1016/j.paerosci.2018.01.001 · Cited by 1,235
Thyavihalli Girijappa, Y. G., Mavinkere Rangappa, S., Parameswaranpillai, J., & Siengchin, S. (2019) · Frontiers in Materials · doi:10.3389/fmats.2019.00226 · Cited by 1,011
A review of natural fibers used in biocomposites: plant, animal and regenerated cellulose fibers
Ramamoorthy, S. K., Skrifvars, M., & Persson, A. (2015) · Polymer Reviews · doi:10.1080/15583724.2014.971124 · Cited by 801
Karimah, A., Ridho, M. R., Munawar, S. S., Adi, D. S., Ismadi, Damayanti, R., Subiyanto, B., Fatriasari, W., & Fudholi, A. (2021) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2021.06.014 · Cited by 771
Metadata
- Authors
- Ku, H., Wang, H., Pattarachaiyakoop, N., & Trada, M.
- Venue
- Composites Part B: Engineering
- Publisher
- Elsevier BV
- Published
- 2011-06
- Volume
- 42
- Issue
- 4
- Pages
- 856-873
- ISSN
- 1359-8368 (ISSN-L)
- OpenAlex
- W1968686179
- Cited by
- 2,280
- References
- 14
- FWCI
- 59.73
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.