The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing
Abstract
Abstract Fused deposition modeling (FDM) has been successfully applied to fabricating short fiber reinforced polymer composites parts. However, due to the intrinsically limited mechanical properties of matrix polymers, there is critical need to develop fiber reinforced high-performance thermoplastic composites for FDM-3D printing to expand engineering applications. In this work, the potential of FDM-3D printing short carbon fiber (CF) and glass fiber (GF) reinforced high-performance PEEK composites has been investigated. Composite filaments with fiber contents of 5 wt%, 10 wt% and 15 wt% were prepared using extrusion process and characterized by micromorphology observation; and thermal properties testing demonstrated its better thermal stability than pure PEEK. The performance evaluation of printed CF/GF-PEEK parts was focused, including mechanical properties, microstructure, surface quality and porosity. The results indicate that the addition of CF/GF to PEEK can significantly enhance the tensile and flexural strength at the cost of ductility. Lower fiber content of 5 wt% is conducive to increasing mechanical properties, improving surface quality and reducing porosity of printed CF/GF-PEEK. GF/PEEK has better interfacial bonding than CF/PEEK due to the different surface treatments on fibers. Furthermore, microstructure observation suggests that fibers aligned along the printing orientation can strengthen the properties, while pores lead to performance degradation of 3D printed CF/GF-PEEK.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Silane coupling agents used for natural fiber/polymer composites: A review
Xie, Y., Hill, C. A. S., Xiao, Z., Militz, H., & Mai, C. (2010) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2010.03.005 · Cited by 2,244
Ning, F., Cong, W., Qiu, J., Wei, J., & Wang, S. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.06.013 · Cited by 1,718
Highly oriented carbon fiber–polymer composites via additive manufacturing
Tekinalp, H. L., Kunc, V., Velez-Garcia, G. M., Duty, C. E., Love, L. J., Naskar, A. K., Blue, C. A., & Ozcan, S. (2014) · Composites Science and Technology · doi:10.1016/j.compscitech.2014.10.009 · Cited by 1,514
A review on additive manufacturing of polymer-fiber composites
Parandoush, P., & Lin, D. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.08.088 · Cited by 1,270
The morphology of poly(aryl-ether-ether-ketone)
Blundell, D. J., & Osborn, B. N. (1983) · Polymer · doi:10.1016/0032-3861(83)90144-1 · Cited by 1,064
Tensile properties of short-glass-fiber- and short-carbon-fiber-reinforced polypropylene composites
Fu, S.-Y., Lauke, B., Mäder, E., Yue, C.-Y., & Hu, X. (2000) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/s1359-835x(00)00068-3 · Cited by 908
An investigation into 3D printing of fibre reinforced thermoplastic composites
Blok, L. G., Longana, M. L., Yu, H., & Woods, B. K. S. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.04.039 · Cited by 866
Fused deposition modeling with polypropylene
Carneiro, O. S., Silva, A. F., & Gomes, R. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.06.053 · Cited by 851
Ferreira, R. T. L., Amatte, I. C., Dutra, T. A., & Bürger, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2017.05.013 · Cited by 764
Cited by
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Shanmugam, V., Rajendran, D. J. J., Babu, K., Rajendran, S., Veerasimman, A., Marimuthu, U., Singh, S., Das, O., Neisiany, R. E., Hedenqvist, M. S., et al. (2021) · Polymer Testing · doi:10.1016/j.polymertesting.2020.106925 · Cited by 268
Yang, D., Cao, Y., Zhang, Z., Yin, Y., & Li, D. (2021) · Polymer Testing · doi:10.1016/j.polymertesting.2021.107149 · Cited by 155
Metadata
- Authors
- Wang, P., Zou, B., Ding, S., Huang, C., Shi, Z., Ma, Y., & Yao, P.
- Venue
- Composites Part B: Engineering
- Publisher
- Elsevier BV
- Published
- 2020-10
- Volume
- 198
- Pages
- 108175
- ISSN
- 1359-8368 (ISSN-L)
- OpenAlex
- W3033863196
- Cited by
- 357
- References
- 37
- FWCI
- 14.68
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing. https://app.cochat.ai/papers/10.1016/j.compositesb.2020.108175
- The paper
- Wang, P., Zou, B., Ding, S., Huang, C., Shi, Z., Ma, Y., & Yao, P. (2020). Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing. Composites Part B: Engineering. https://doi.org/10.1016/j.compositesb.2020.108175
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
