The DOI matches its Crossref record; 25 of the 25 references it cites were found in a registry or an index.
Melting and solidification of PCM embedded in porous metal foam in horizontal multi-tube heat storage system
Abstract
In this paper, melting and solidification processes of phase change material embedded in metallic porous foam in a multi-tube heat exchanger are investigated numerically under local non-equilibrium thermal condition. RT 35 is used as phase change material in middle shell of 3D multi-tube heat exchanger. Also, water flows across inner tube/tubes and outer tube as a heat transfer fluid (HTF). The effects of number of inner tubes, their arrangement as well as porosity of metallic foam on thermal characteristics of heat storage unit are studied. Results show that increasing number of inner tubes and adding metallic foam enhance melting and solidification rates significantly. A composite of phase change material/metallic foam with porosity of e = 0.7 engenders shorter melting and solidification time comparing to pure PCM. Arrangement of inner tubes has no effect on melting rate of metal foam/PCM composite. By inserting metallic foam with porosities e = 0.9 and e = 0.7 , melting time is decreased by 14% and 55%, respectively. Highest melting rate is for case with four inner tubes for all porosities of metallic foam. Regarding solidification process in pure PCM, case with four tubes shows shorter solidification time. Also, highest solidification rate amid composites of phase change material/metallic foam is seen for case with three tubes. Consequently, inserting metallic foam is more efficient in solidification process rather than the melting one. Moreover, increasing number of inner tubes has more influence on phase change rates in metal foam/PCM composites compared to pure PCM.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Heat Transfer from Tubes in Crossflow
Žukauskas, A. (1972) · Advances in Heat Transfer · doi:10.1016/s0065-2717(08)70038-8 · Cited by 1,408
Forced Convection in High Porosity Metal Foams
Calmidi, V. V., & Mahajan, R. L. (2000) · Journal of Heat Transfer · doi:10.1115/1.1287793 · Cited by 1,166
Zhao, C. Y., Lu, W., & Tian, Y. (2010) · Solar Energy · doi:10.1016/j.solener.2010.04.022 · Cited by 757
Enhance heat transfer for PCM melting in triplex tube with internal–external fins
Mat, S., Al-Abidi, A. A., Sopian, K., Sulaiman, M. Y., & Mohammad, A. T. (2013) · Energy Conversion and Management · doi:10.1016/j.enconman.2013.05.003 · Cited by 604
Zhang, P., Meng, Z. N., Zhu, H., Wang, Y. L., & Peng, S. P. (2017) · Applied Energy · doi:10.1016/j.apenergy.2015.10.075 · Cited by 497
Tian, Y., & Zhao, C. Y. (2011) · Energy · doi:10.1016/j.energy.2011.07.019 · Cited by 495
Al-Waeli, A. H. A., Sopian, K., Chaichan, M. T., Kazem, H. A., Ibrahim, A., Mat, S., & Ruslan, M. H. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.09.032 · Cited by 433
Liu, Z., Yao, Y., & Wu, H. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.02.022 · Cited by 405
Thermal performance of copper foam/paraffin composite phase change material
Zheng, H., Wang, C., Liu, Q., Tian, Z., & Fan, X. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.12.023 · Cited by 404
Al-Abidi, A. A., Mat, S., Sopian, K., Sulaiman, M. Y., & Mohammad, A. T. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.02.030 · Cited by 387
Numerical study on melting of paraffin wax with Al2O3 in a square enclosure
Arasu, A. V., & Mujumdar, A. S. (2012) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2011.09.013 · Cited by 330
Rabienataj Darzi, A. A., Jourabian, M., & Farhadi, M. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.04.016 · Cited by 329
Self-citationMahdi, J. M., & Nsofor, E. C. (2017) · Applied Energy · doi:10.1016/j.apenergy.2016.11.036 · Cited by 322
Non-uniform heat transfer suppression to enhance PCM melting by angled fins
Ji, C., Qin, Z., Low, Z., Dubey, S., Choo, F. H., & Duan, F. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2017.10.030 · Cited by 312
Heat Transfer from Tubes in Crossflow
Žkauskas, A. (1987) · Advances in Heat Transfer · doi:10.1016/s0065-2717(08)70118-7 · Cited by 288
Nano-PCMs for enhanced energy storage and passive cooling applications
Colla, L., Fedele, L., Mancin, S., Danza, L., & Manca, O. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.03.161 · Cited by 283
Experimental analysis of phase change phenomenon of paraffin waxes embedded in copper foams
Mancin, S., Diani, A., Doretti, L., Hooman, K., & Rossetto, L. (2015) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2014.11.023 · Cited by 261
Heat pipe with nano enhanced-PCM for electronic cooling application
Krishna, J., Kishore, P. S., & Solomon, A. B. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2016.10.014 · Cited by 247
A numerical method for PCM-based pin fin heat sinks optimization
Pakrouh, R., Hosseini, M. J., Ranjbar, A. A., & Bahrampoury, R. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.07.003 · Cited by 245
Parsazadeh, M., & Duan, X. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.02.052 · Cited by 209
Alshaer, W. G., Nada, S. A., Rady, M. A., Le Bot, C., & Palomo Del Barrio, E. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.10.045 · Cited by 196
Mahdi, J. M., & Nsofor, E. C. (2017) · Energy · doi:10.1016/j.energy.2017.03.060 · Cited by 192
Melting behaviors of PCM in porous metal foam characterized by fractal geometry
Deng, Z., Liu, X., Zhang, C., Huang, Y., & Chen, Y. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.05.126 · Cited by 131
Zhang, P., Meng, Z., Zhu, H., Wang, Y., & Peng, S. (2015) · Energy Procedia · doi:10.1016/j.egypro.2015.07.637 · Cited by 77
Efficient modeling of phase change material solidification with multidimensional fins
Pan, C., Hoenig, S. H., Chen, C., Neti, S., Romero, C. E., & Vermaak, N. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.07.120 · Cited by 26
Cited by
A comparative study on battery thermal management using phase change material (PCM)
Verma, A., Shashidhara, S., & Rakshit, D. (2019) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2019.03.003 · Cited by 315
Effect of geometric parameter and nanoparticles on PCM melting in a vertical shell-tube system
Nie, C., Liu, J., & Deng, S. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116290 · Cited by 75
Metadata
- Authors
- Esapour, M., Hamzehnezhad, A., Rabienataj Darzi, A. A., & Jourabian, M.
- Venue
- Energy Conversion and Management
- Publisher
- Elsevier BV
- Published
- 2018-09
- Volume
- 171
- Pages
- 398-410
- ISSN
- 0196-8904 (ISSN-L)
- OpenAlex
- W2805264571
- Cited by
- 342
- References
- 25
- FWCI
- 18.71
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.