Experimental investigation of melting behaviour of phase change material in finned rectangular enclosures under different inclination angles
The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Abstract
The deployment of phase change materials (PCMs) in practical applications is in large part limited by the low thermal conductivity of the available PCMs. Hence, in this study, enhancement in the melting rate of PCM by addition of fins in rectangular enclosures was experimentally investigated under different inclination angles. The melting process of lauric acid in side-heated enclosures with different numbers of fins was evaluated for inclination angles of 90° (vertical), 45° and 0° (horizontal). In order to visualize the melting process, the enclosure was fabricated from transparent acrylic material except one side made of an aluminum plate to heat the enclosure isothermally. Solid-liquid interface positions and temperature history of the PCM were recorded and applied to calculate the liquid fractions and heat transfer rates. The evolution of the interface in the inclined enclosures revealed that the development of vortical flow structures in the liquid PCM by decreasing the inclination angle significantly improves the melting rate. It was found that for both finned and unfinned enclosures the melting rate increases by reducing the inclination angle. Heat transfer enhancements obtained by the 0-fin horizontal and 3-fin vertical enclosures compared to the 0-fin vertical enclosure were 115% and 56%, respectively. This thermal behavior proposes that simply inclining the enclosure can be more effective to enhance the melting rate than adding fins to the vertical enclosure. Among the different cases studied, the 3-fin horizontal enclosure showed the maximum heat transfer rate and consequently the minimum melting time. The present investigation can contribute to a better understanding of PCM melting in the inclined finned enclosures and provide much-needed benchmark data for the future numerical simulations.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
(1953) · Mechanical Engineering · Cited by 6,608
Ibrahim, N. I., Al-Sulaiman, F. A., Rahman, S., Yilbas, B. S., & Sahin, A. Z. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.01.169 · Cited by 580
Thermal regulation of building-integrated photovoltaics using phase change materials
Huang, M. J., Eames, P., & Norton, B. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2003.11.015 · Cited by 525
Kamkari, B., & Shokouhmand, H. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.07.056 · Cited by 437
Self-citationKamkari, B., Shokouhmand, H., & Bruno, F. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.01.014 · Cited by 434
Self-citationShokouhmand, H., & Kamkari, B. (2013) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2013.06.010 · Cited by 343
Self-citationA review on thermophysical properties of nanoparticle dispersed phase change materials
Kibria, M. A., Anisur, M. R., Mahfuz, M. H., Saidur, R., & Metselaar, I. H. S. C. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.02.028 · Cited by 317
Non-uniform heat transfer suppression to enhance PCM melting by angled fins
Ji, C., Qin, Z., Low, Z., Dubey, S., Choo, F. H., & Duan, F. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2017.10.030 · Cited by 312
Chandel, S. S., & Agarwal, T. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.02.001 · Cited by 299
Zhao, J., Lv, P., & Rao, Z. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2016.11.017 · Cited by 270
Faegh, M., & Shafii, M. B. (2017) · Desalination · doi:10.1016/j.desal.2017.01.023 · Cited by 261
Heat pipe with nano enhanced-PCM for electronic cooling application
Krishna, J., Kishore, P. S., & Solomon, A. B. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2016.10.014 · Cited by 247
Experimental and numerical evaluation of longitudinally finned latent heat thermal storage systems
Hosseini, M. J., Ranjbar, A. A., Rahimi, M., & Bahrampoury, R. (2015) · Energy and Buildings · doi:10.1016/j.enbuild.2015.04.045 · Cited by 214
Enhancement of latent heat energy storage using embedded heat pipes
Robak, C. W., Bergman, T. L., & Faghri, A. (2011) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2011.03.038 · Cited by 210
Khanna, S., Reddy, K. S., & Mallick, T. K. (2017) · Energy · doi:10.1016/j.energy.2017.05.150 · Cited by 201
Liu, C., & Groulx, D. (2014) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2014.03.014 · Cited by 199
Self-citationKousha, N., Hosseini, M. J., Aligoodarz, M. R., Pakrouh, R., & Bahrampoury, R. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.10.203 · Cited by 190
Baby, R., & Balaji, C. (2013) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2013.05.018 · Cited by 182
Effect of porosity of conducting matrix on a phase change energy storage device
Atal, A., Wang, Y., Harsha, M., & Sengupta, S. (2016) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2015.09.033 · Cited by 176
Wang, Y., & Yang, Y.-T. (2011) · Energy · doi:10.1016/j.energy.2011.06.023 · Cited by 172
Influence of fin size and distribution on solid-liquid phase change in a rectangular enclosure
Biwole, P. H., Groulx, D., Souayfane, F., & Chiu, T. (2018) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2017.10.038 · Cited by 171
Self-citationKim, T. Y., Hyun, B.-S., Lee, J.-J., & Rhee, J.-H. (2012) · Aerospace Science and Technology · doi:10.1016/j.ast.2012.05.007 · Cited by 157
Rozenfeld, A., Kozak, Y., Rozenfeld, T., et al. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.03.020 · Cited by 140
Optimization of a solar air heater with phase change materials: Experimental and numerical study
Moradi, R., Kianifar, A., & Wongwises, S. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2017.07.011 · Cited by 130
A storage domestic solar hot water system with a back layer of phase change material
Khalifa, A. J. N., Suffer, K. H., & Mahmoud, M. S. (2012) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2012.05.017 · Cited by 129
Lacroix, M., & Benmadda, M. (1997) · Numerical Heat Transfer Part A Applications · doi:10.1080/10407789708914026 · Cited by 129
Dodecanoic acid as a promising phase-change material for thermal energy storage
Desgrosseilliers, L., Whitman, C. A., Groulx, D., & White, M. A. (2013) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2012.12.031 · Cited by 98
Self-citationFins and turbulence promoters for heat transfer enhancement in latent heat storage systems
Ismail, K. A. R., & Lino, F. A. M. (2011) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2011.02.002 · Cited by 89
Allen, M. J., Sharifi, N., Faghri, A., & Bergman, T. L. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.09.071 · Cited by 84
Experimental study of a latent heat thermal energy storage system assisted by a heat pipe network
Tiari, S., Mahdavi, M., & Qiu, S. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.10.019 · Cited by 80
Bondareva, N. S., & Sheremet, M. А. (2016) · Journal of Magnetism and Magnetic Materials · doi:10.1016/j.jmmm.2016.06.050 · Cited by 69
Ogoh, W., & Groulx, D. (2012) · Heat and Mass Transfer · doi:10.1007/s00231-012-1029-3 · Cited by 67
Self-citationFalco, M. D., Capocelli, M., & Giannattasio, A. (2016) · Energy and Buildings · doi:10.1016/j.enbuild.2016.04.016 · Cited by 55
3D natural convection melting in a cubical cavity with a heat source
Bondareva, N. S., & Sheremet, M. А. (2017) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2017.01.021 · Cited by 42
Cited by
A review of melting and freezing processes of PCM/nano-PCM and their application in energy storage
Rostami, S., Afrand, M., Shahsavar, A., Sheikholeslami, M., Kalbasi, R., Aghakhani, S., Shadloo, M. S., & Oztop, H. F. (2020) · Energy · doi:10.1016/j.energy.2020.118698 · Cited by 444
A review on macro-encapsulated phase change material for building envelope applications
Liu, Z., Yu, Z. (., Yang, T., Qin, D., Li, S., Zhang, G., Haghighat, F., & Joybari, M. M. (2018) · Building and Environment · doi:10.1016/j.buildenv.2018.08.030 · Cited by 322
Melting process of nanoparticle enhanced PCM through storage cylinder incorporating fins
Li, F., Almarashi, A., Jafaryar, M., Hajizadeh, M. R., & Chu, Y.-M. (2021) · Powder Technology · doi:10.1016/j.powtec.2020.12.026 · Cited by 184
Nakhchi, M. E., Hatami, M., & Rahmati, M. (2021) · Energy · doi:10.1016/j.energy.2020.119112 · Cited by 78
Metadata
- Authors
- Kamkari, B., & Groulx, D.
- Venue
- Experimental Thermal and Fluid Science
- Publisher
- Elsevier BV
- Published
- 2018-10
- Volume
- 97
- Pages
- 94-108
- ISSN
- 0894-1777 (ISSN-L)
- OpenAlex
- W2798233671
- Cited by
- 261
- References
- 34
- FWCI
- 11.51
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.