The DOI matches its Crossref record.
Cyclic deformation and fatigue behavior of additively manufactured 17–4 PH stainless steel
Open accessAbstract
Abstract Static and fatigue experiments were conducted on conventionally manufactured (CM) and additively manufactured (AM) 17–4 PH stainless steels in ambient air. The fatigue experiments were tested under the fully reversed strain-controlled condition with the strain amplitudes ranging from 0.15% to 1.0%. The two manufacturing conditions result in similar tensile strengths but the AM 17–4 PH stainless steel has a significantly lower ductility than that of the CM steel. The fatigue limit of the CM 17–4 PH stainless steel is approximately 640 MPa and the fatigue limit of the AM steel is approximately 300 MPa. The strain-life fatigue curves of both materials display a kink point from low cycle fatigue regime to high cycle fatigue regime. Defects and porosity from the additive manufacturing process contribute to the weakened fatigue properties and ductility of the AM stainless steel.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Steels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Narasimharaju, S. R., Zeng, W., See, T. L., Zhu, Z., Scott, P., Jiang, X., & Lou, S. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.12.033 · Cited by 508
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Metadata
- Authors
- Carneiro, L., Jalalahmadi, B., Ashtekar, A., & Jiang, Y.
- Venue
- International Journal of Fatigue
- Publisher
- Elsevier BV
- Published
- 2019-06
- Volume
- 123
- Pages
- 22-30
- ISSN
- 0142-1123 (ISSN-L)
- OpenAlex
- W2912711801
- Cited by
- 180
- References
- 0
- FWCI
- 11.76
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Cyclic deformation and fatigue behavior of additively manufactured 17–4 PH stainless steel. https://app.cochat.ai/papers/10.1016/j.ijfatigue.2019.02.006
- The paper
- Carneiro, L., Jalalahmadi, B., Ashtekar, A., & Jiang, Y. (2019). Cyclic deformation and fatigue behavior of additively manufactured 17–4 PH stainless steel. International Journal of Fatigue. https://doi.org/10.1016/j.ijfatigue.2019.02.006
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.