The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Fatigue behavior of additively manufactured 17-4 PH stainless steel: Synergistic effects of surface roughness and heat treatment
Open accessAbstract
In this study, the synergistic effects of heat treatment and surface roughness on the microstructure and mechanical properties of laser powder bed fusion (L-PBF) 17-4 precipitation hardening (PH) stainless steel (SS) were investigated under monotonic tensile and fatigue loading. Five different heat treatment procedures, with and without primary solution treating cycle, i.e. Condition A (CA), were applied on L-PBF specimens in both as-built and machined surface conditions. Monotonic tensile tests were conducted at a strain rate of 0.001 s−1 and, uniaxial fully-reversed (R = −1) strain-controlled fatigue tests were carried out at various strain amplitudes ranging from 0.001 to 0.004 mm/mm. The heat treatment procedures were found to have a significant effect on the microstructure and mechanical properties of L-PBF 17-4 PH SS with the CA thermal cycle improving the fatigue strength considerably. This is due to the more homogenized microstructure obtained after performing the CA thermal cycle. In addition, eliminating the effect of surface roughness by machining and polishing processes enhanced the fatigue strength of the material, somewhat comparable to the one of the wrought counterpart. Fractography analysis revealed surface micro-notches and internal pores as the primary crack initiating factors in the as-built and machined specimens, respectively.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Cited by
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Steels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
An overview of modern metal additive manufacturing technology
Armstrong, M., Mehrabi, H., & Naveed, N. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.10.060 · Cited by 549
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Metadata
- Authors
- Nezhadfar, P. D., Shrestha, R., Phan, N., & Shamsaei, N.
- Venue
- International Journal of Fatigue
- Publisher
- Elsevier BV
- Published
- 2019-07
- Volume
- 124
- Pages
- 188-204
- ISSN
- 0142-1123 (ISSN-L)
- OpenAlex
- W2916023266
- Cited by
- 166
- References
- 2
- FWCI
- 12.14
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Fatigue behavior of additively manufactured 17-4 PH stainless steel: Synergistic effects of surface roughness and heat treatment. https://app.cochat.ai/papers/10.1016/j.ijfatigue.2019.02.039
- The paper
- Nezhadfar, P. D., Shrestha, R., Phan, N., & Shamsaei, N. (2019). Fatigue behavior of additively manufactured 17-4 PH stainless steel: Synergistic effects of surface roughness and heat treatment. International Journal of Fatigue. https://doi.org/10.1016/j.ijfatigue.2019.02.039
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.