The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
Influence of re-melting on surface roughness and porosity of AlSi10Mg parts fabricated by selective laser melting
Open accessAbstract
Re-melting strategies with same and opposite directions to the first scanning routine were performed in AlSi10Mg parts by selective laser melting (SLM) technology. Surface roughness and porosity were investigated with confocal microscopy , micro-computed tomography (CT) and optical microscopy (OM). Re-melting facilitates the top surface finish with Ra value decreasing from 20.67 μm to 11.67 μm (same direction) and 10.87 μm (opposite direction), almost at the same level. On side surface there is a contradictory trend. Pores at SLM parts include spherical pores due to entrapped gases, irregular pores for lack of fusion, and keyhole pores because of laser movement. The former two kinds form in the central areas while the latter one is located at edges of melting tracks and exhibits different distribution at both sides. Re-melting allows more chances for pores (spherical and keyhole pores) to escape from the melting pools. Irregular pores decrease because smoother surface allows powders to be fully melted. Porosity decrease of both re-melting strategies in central areas of the SLM parts is almost on the same level while same directional re-melting exhibits superior ability to release porosity at edges because of the porosity distribution difference at the head and wake of the melting tracks.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
3D printing of high-strength aluminium alloys
Martin, J. H., Yahata, B. D., Hundley, J. M., Mayer, J. A., Schaedler, T. A., & Pollock, T. M. (2017) · Nature · doi:10.1038/nature23894 · Cited by 2,950
Review of selective laser melting: Materials and applications
Yap, C. Y., Chua, C. K., Dong, Z. L., Liu, Z. H., Zhang, D. Q., Loh, L. E., & Sing, S. L. (2015) · Applied Physics Reviews · doi:10.1063/1.4935926 · Cited by 2,353
Self-citationObservation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Read, N., Wang, W., Essa, K., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.044 · Cited by 1,218
Zhang, J., Song, B., Wei, Q., Bourell, D., & Shi, Y. (2019) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2018.09.004 · Cited by 1,205
Brandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,151
Selective laser melting of aluminium components
Louvis, E., Fox, P., & Sutcliffe, C. J. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.019 · Cited by 933
In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing
Leung, C. L. A., Marussi, S., Atwood, R. C., Towrie, M., Withers, P. J., & Lee, P. D. (2018) · Nature Communications · doi:10.1038/s41467-018-03734-7 · Cited by 817
Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg
Weingarten, C., Buchbinder, D., Pirch, N., Meiners, W., Wissenbach, K., & Poprawe, R. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.02.013 · Cited by 585
Kimura, T., & Nakamoto, T. (2016) · Materials & Design · doi:10.1016/j.matdes.2015.10.065 · Cited by 404
Yasa, E., Deckers, J., & Kruth, J. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156450 · Cited by 371
Yuan, P., & Gu, D. (2015) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/48/3/035303 · Cited by 345
Problems and issues in laser beam welding of aluminum–lithium alloys
Xiao, R., & Zhang, X. (2014) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2013.10.005 · Cited by 325
Damage evolution and failure mechanisms in additively manufactured stainless steel
Carlton, H. D., Haboub, A., Gallegos, G. F., Parkinson, D. Y., & MacDowell, A. A. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.073 · Cited by 313
AlMangour, B., Grzesiak, D., & Yang, J.-M. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2017.08.022 · Cited by 259
Yang, T., Liu, T., Liao, W., MacDonald, E. W., Wei, H., Chen, X., & Jiang, L. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2018.10.015 · Cited by 210
Darvish, K., Chen, Z. W., & Pasang, T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.09.086 · Cited by 193
Investigation of the accuracy and roughness in the laser powder bed fusion process
Calignano, F. (2018) · Virtual and Physical Prototyping · doi:10.1080/17452759.2018.1426368 · Cited by 167
Sing, S. L., Wiria, F. E., & Yeong, W. Y. (2018) · International Journal of Refractory Metals and Hard Materials · doi:10.1016/j.ijrmhm.2018.08.006 · Cited by 163
Self-citationSelective laser remelting of an additive layer manufacturing process on AlSi10Mg
Liu, B., Li, B.-Q., & Li, Z. (2019) · Results in Physics · doi:10.1016/j.rinp.2018.12.018 · Cited by 158
Zhang, C., Zhu, H., Hu, Z., Zhang, L., & Zeng, X. (2019) · Materials Science and Engineering A · doi:10.1016/j.msea.2019.01.024 · Cited by 134
Han, Q., & Jiao, Y. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-03272-y · Cited by 132
Selective laser remelting of an additively manufactured Cu-Al-Ni-Mn shape-memory alloy
Gustmann, T., Schwab, H., Kühn, U., & Pauly, S. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.05.010 · Cited by 120
Li, R., Jin, Y., Li, Z., Zhu, Y., & Wu, M. (2014) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2014.09.067 · Cited by 77
Fatemi, S., Ashani, J. Z., Aghchai, A. J., & Abolghasemi, A. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1293274 · Cited by 62
Yang, X., Liu, J., Cui, X., Jin, G. D., Liu, Z., Chen, Y., & Feng, X. (2019) · Journal of Physics and Chemistry of Solids · doi:10.1016/j.jpcs.2019.03.001 · Cited by 56
Cited by
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
A review on machine learning in 3D printing: applications, potential, and challenges
Goh, G. D., Sing, S. L., & Yeong, W. Y. (2021) · Artificial Intelligence Review · doi:10.1007/s10462-020-09876-9 · Cited by 652
Self-citationSurface post-treatments for metal additive manufacturing: Progress, challenges, and opportunities
Maleki, E., Bagherifard, S., Bandini, M., & Guagliano, M. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101619 · Cited by 528
Metallurgy, mechanistic models and machine learning in metal printing
DebRoy, T., Mukherjee, T., Wei, H. L., Elmer, J. W., & Milewski, J. O. (2020) · Nature Reviews Materials · doi:10.1038/s41578-020-00236-1 · Cited by 497
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Metadata
- Authors
- Yu, W., Sing, S. L., Chua, C. K., & Tian, X.
- Venue
- Journal of Alloys and Compounds
- Publisher
- Elsevier BV
- Published
- 2019-07
- Volume
- 792
- Pages
- 574-581
- ISSN
- 0925-8388 (ISSN-L)
- OpenAlex
- W2931028544
- Cited by
- 303
- References
- 28
- FWCI
- 25.12
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.