The DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index.
Density and mechanical properties in selective laser melting of Invar 36 and stainless steel 316L
Open accessAbstract
In this study, the process-structure-property relationship for selective laser melting of Invar 36 and stainless steel 316L is discussed. Invar 36 and stainless steel 316L have been used in various industrial applications for their unique properties, especially in the aerospace industry. Invar 36 offers a very low coefficient of thermal expansion while stainless steel 316L offers high corrosion resistance. Since both materials are weldable, but hard to machine, this study is aimed at finding the optimum laser process parameters for producing dense components from both alloys. A full factorial design of experiments was formulated in this paper to study a wide range of process parameters for both materials. The bulk density, tensile mechanical properties, fractography, material composition, and residual stresses of the parts produced were investigated. An optimum process window has been suggested based on experimental work. The induced residual stresses were categorized into two categories: microscopic residual stresses and macroscopic residual stresses. The microscopic residual stresses were measured using X-ray diffraction method and the macroscopic residual stresses were measured using cantilever deflection method and finite element simulations. The paper proposes two laser energy densities for each material: brittle-ductile transition energy density, E T , and critical laser energy density, E C . Below the brittle-ductile transition energy density, the parts exhibited void formation, low density, and brittle fracture. Above the critical energy density, the parts showed vaporization of some alloying elements that have low boiling temperatures. Stable melting ranges were found to occur between these two laser energy densities: 52.1–86.8 J/mm 3 for Invar 36 and 62.5–104.2 J/mm 3 for stainless steel 316L.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Shigley's Mechanical Engineering Design
Budynas, R. G., & Nisbett, J. K. (1972) · Virtual Defense Library (Ministerio de Defensa) · Cited by 1,893
Liverani, E., Toschi, S., Ceschini, L., & Fortunato, A. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.05.042 · Cited by 990
Balling behavior of stainless steel and nickel powder during selective laser melting process
Li, R., Liu, J., Shi, Y., Wang, L., & Jiang, W. (2012) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3566-1 · Cited by 722
Selective laser melting of stainless steel 316L with low porosity and high build rates
Sun, Z., Tan, X., Tor, S. B., & Yeong, W. Y. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.05.035 · Cited by 714
Investigations on residual stresses and deformations in selective laser melting
Zaeh, M. F., & Branner, G. (2010) · Production Engineering · doi:10.1007/s11740-009-0192-y · Cited by 666
Handbook of Residual Stress and Deformation of Steel
Totten, G. E., Howes, M. K., & 井上, 達. (2001) · Cited by 661
A study on the residual stress during selective laser melting (SLM) of metallic powder
Liu, Y., Yang, Y., & Wang, D. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-8466-y · Cited by 573
Casati, R., Lemke, J., & Vedani, M. (2016) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2016.06.016 · Cited by 542
Stress and deformation evaluations of scanning strategy effect in selective laser melting
Cheng, B., Shrestha, S., & Chou, K. (2016) · Additive Manufacturing · doi:10.1016/j.addma.2016.05.007 · Cited by 504
Kurzynowski, T., Gruber, K., Stopyra, W., Kuźnicka, B., & Chlebus, E. (2018) · Materials Science and Engineering: A · doi:10.1016/j.msea.2018.01.103 · Cited by 489
Effect of molten pool boundaries on the mechanical properties of selective laser melting parts
Shifeng, W., Shuai, L., Qingsong, W., Yan, C., Sheng, Z., & Yusheng, S. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.002 · Cited by 449
Kamath, C., El-dasher, B., Gallegos, G. F., King, W. E., & Sisto, A. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-5954-9 · Cited by 395
Yadroitsev, I., & Yadroitsava, I. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1026045 · Cited by 349
Yadroitsev, I., & Smurov, I. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.083 · Cited by 339
Part and material properties in selective laser melting of metals
Kruth, J., Badrossamay, M., Yasa, E., Deckers, J. P., Thijs, L., & Humbeeck, J. V. (2010) · Lirias · Cited by 303
Selective laser melting of Invar 36: Microstructure and properties
Qiu, C., Adkins, N. J. E., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.10.020 · Cited by 292
Manufacturing by combining Selective Laser Melting and Selective Laser Erosion/laser re-melting
Yasa, E., Kruth, J.-P., & Deckers, J. (2011) · CIRP Annals · doi:10.1016/j.cirp.2011.03.063 · Cited by 265
Stress and Deformation Evaluations of Scanning Strategy Effect in Selective Laser Melting
Cheng, B., Shrestha, S., & Chou, Y. K. (2016) · Volume 3: Joint MSEC-NAMRC Symposia · doi:10.1115/msec2016-8819 · Cited by 250
Yusuf, S. M., Chen, Y., Boardman, R., Yang, S., & Gao, N. (2017) · Metals · doi:10.3390/met7020064 · Cited by 230
The selection of process parameters in additive manufacturing for aerospace alloys
Yakout, M., Cadamuro, A., Elbestawi, M. A., & Veldhuis, S. C. (2017) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-017-0280-7 · Cited by 209
Self-citationDensity of Additively-Manufactured, 316L SS Parts Using Laser Powder-Bed Fusion at Powers Up to 400W
Lawrence Livermore National Lab. (LLNL), L., Kamath, C., USDOE, El-dasher, B., Gallegos, G., King, W. E., & Sisto, A. (2013) · doi:10.2172/1116929 · Cited by 207
Spierings, A. B., & Levy, G. N. (2009) · doi:10.26153/tsw/15113 · Cited by 193
Miranda, G., Faria, S., Bartolomeu, F., Pinto, E., Madeira, S., Mateus, A., Carreira, P., Alves, N., Silva, F. S., & Carvalho, O. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.01.028 · Cited by 187
Liu, B., Wildman, R. D., Tuck, C. J., Ashcroft, I., & Hague, R. (2011) · doi:10.26153/tsw/15290 · Cited by 159
Thermal expansion coefficients in Invar processed by selective laser melting
Harrison, N. J., Todd, I., & Mumtaz, K. (2017) · Journal of Materials Science · doi:10.1007/s10853-017-1169-4 · Cited by 117
Alloying element vaporization during laser spot welding of stainless steel
He, X., DebRoy, T., & Fuerschbach, P. W. (2003) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/36/23/033 · Cited by 112
On the characterization of stainless steel 316L parts produced by selective laser melting
Yakout, M., Elbestawi, M. A., & Veldhuis, S. C. (2017) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-017-1303-0 · Cited by 108
Self-citationResidual Stress in Metal Specimens Produced by Direct Metal Laser Sintering
Yadroitsava, I., & Yadroitsev, I. A. (2015) · Cited by 26
Cited by
SLM lattice structures: Properties, performance, applications and challenges
Maconachie, T., Leary, M., Lozanovski, B., Zhang, X., Qian, M., Faruque, O., & Brandt, M. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108137 · Cited by 1,497
Paolini, A., Kollmannsberger, S., & Rank, E. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100894 · Cited by 673
Narasimharaju, S. R., Zeng, W., See, T. L., Zhu, Z., Scott, P., Jiang, X., & Lou, S. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.12.033 · Cited by 508
Methods and materials for additive manufacturing: A critical review on advancements and challenges
Bhuvanesh Kumar, M., & Sathiya, P. (2021) · Thin-Walled Structures · doi:10.1016/j.tws.2020.107228 · Cited by 372
Alami, A. H., Ghani Olabi, A., Alashkar, A., Alasad, S., Aljaghoub, H., Rezk, H., & Abdelkareem, M. A. (2023) · Ain Shams Engineering Journal · doi:10.1016/j.asej.2023.102516 · Cited by 349
Metadata
- Authors
- Yakout, M., Elbestawi, M. A., & Veldhuis, S. C.
- Venue
- Journal of Materials Processing Technology
- Publisher
- Elsevier BV
- Published
- 2019-04
- Volume
- 266
- Pages
- 397-420
- ISSN
- 0924-0136 (ISSN-L)
- OpenAlex
- W2899839852
- Cited by
- 275
- References
- 29
- FWCI
- 12.63
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.