The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting
Abstract
Abstract A357 alloy was manufactured by selective laser melting (SLM) and subjected to different heat treatments, by considering the stress relief step as critical, to establish the microstructure-mechanical property relationship and model the yield strength. For the as-SLM processed condition, the imposed fast cooling rate refines and limits the amount of Fe-rich intermetallic and eutectic Mg2Si phases, and enables a higher level of supersaturation of solutes. The latter leads to significant yield strength contributions from solid solution strengthening and natural ageing. The inter-cellular Si network within the columnar grains remains unchanged but small Si-rich particles appear within cells after direct ageing. The Si network breaks up during stress relieving, leading to high ductility. The lower ductility for the vertically-built samples under as-SLM processed, directly aged, and stress relieved conditions is due mainly to the finer Si networks brittle nature. Porosity resulting from trapped hydrogen gas enlarges significantly with solutionisation, deteriorating the ductility. Grain growth is not obviously observed with heat treatment. Si particles coarsen preferentially at grain boundaries initially, however, they distribute more evenly by coarsening within the grains as well during prolonged solutionisation. Anisotropy in both yield strength and ductility subsequently disappears when a more homogeneous microstructure is obtained.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Phase Transformations in Metals and Alloys
Porter, D. A., & Easterling, K. E. (1992) · doi:10.1007/978-1-4899-3051-4 · Cited by 4,904
Cited by
About metastable cellular structure in additively manufactured austenitic stainless steels
Kong, D., Dong, C., Wei, S., Ni, X., Zhang, L., Li, R., Wang, L., Man, C., & Li, X. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101804 · Cited by 528
Sola, A., & Nouri, A. (2019) · Journal of Advanced Manufacturing and Processing · doi:10.1002/amp2.10021 · Cited by 378
Review of high-strength aluminium alloys for additive manufacturing by laser powder bed fusion
Rometsch, P. A., Zhu, Y., Wu, X., & Huang, A. (2022) · Materials & Design · doi:10.1016/j.matdes.2022.110779 · Cited by 330
Self-citationCoated metal powders for laser powder bed fusion (L-PBF) processing: A review
Bidulsky, R., Gobber, F. S., Bidulska, J., Ceroni, M., Kvackaj, T., & Grande, M. A. (2021) · Metals · doi:10.3390/met11111831 · Cited by 68
Metadata
- Authors
- Yang, K. V., Rometsch, P., Davies, C. H. J., Huang, A., & Wu, X.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2018-09
- Volume
- 154
- Pages
- 275-290
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2804209774
- Cited by
- 243
- References
- 1
- FWCI
- 12.15
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting. https://app.cochat.ai/papers/10.1016/j.matdes.2018.05.026
- The paper
- Yang, K. V., Rometsch, P., Davies, C. H. J., Huang, A., & Wu, X. (2018). Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting. Materials & Design. https://doi.org/10.1016/j.matdes.2018.05.026
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.