The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Laser additive manufacturing of Zn metal parts for biodegradable applications: Processing, formation quality and mechanical properties
Abstract
Abstract Zn based metals have exhibited promising applications for biodegradable implants. Only a handful of very recent reports were found on additive manufacturing of Zn metal by selective laser melting (SLM). This work provided a systematic study on densification, surface roughness and mechanical properties regarding SLM of Zn metal. Single track surface after laser melting was rugged and twisted with a large amount of attached particles due to severe Zn evaporation. For SLM produced solid parts, the relative density was more than 99.50%; the surface roughness Sa was 9.15–10.79 μm for as-melted status and 4.83 μm after sandblasting, both comparable to optimal results obtained by SLM of common metals. The microstructure was made up of fine columnar grains. The average values of hardness, elastic modulus, yield strength, ultimate strength and elongation were 42 HV, 23GPa, 114 MPa, 134 MPa, and 10.1% respectively, better than those obtained by most manufacturing methods. The superior mechanical properties were attributed to high densification and fine grains resulted by optimal processing control of Zn evaporation and laser energy input. Cardiovascular stents were printed out to demonstrate additive manufacturing ability for complicated structures. All the results indicate the encouraging prospect of additive manufacturing of Zn based metals for biodegradable applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Long-term surveillance of zinc implant in murine artery: Surprisingly steady biocorrosion rate
Drelich, A. J., Zhao, S., Guillory, R. J., Drelich, J. W., & Goldman, J. (2017) · Acta Biomaterialia · doi:10.1016/j.actbio.2017.05.045 · Cited by 188
Cited by
Surface post-treatments for metal additive manufacturing: Progress, challenges, and opportunities
Maleki, E., Bagherifard, S., Bandini, M., & Guagliano, M. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101619 · Cited by 528
Mg bone implant: Features, developments and perspectives
Yang, Y., He, C., Dianyu, E., Yang, W., Qi, F., Xie, D., Shen, L., Peng, S., & Shuai, C. (2020) · Materials & Design · doi:10.1016/j.matdes.2019.108259 · Cited by 433
Kabir, H., Munir, K., Wen, C., & Li, Y. (2021) · Bioactive Materials · doi:10.1016/j.bioactmat.2020.09.013 · Cited by 397
Current status and perspectives of zinc-based absorbable alloys for biomedical applications
Hernández-Escobar, D., Champagne, S., Yilmazer, H., Dikici, B., Boehlert, C. J., & Hermawan, H. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2019.07.034 · Cited by 309
Additive manufacturing of biodegradable metals: Current research status and future perspectives
Qin, Y., Wen, P., Guo, H., Xia, D., Zheng, Y., Jauer, L., Poprawe, R., Voshage, M., & Schleifenbaum, J. H. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2019.04.046 · Cited by 303
Self-citation
Metadata
- Authors
- Wen, P., Voshage, M., Jauer, L., Chen, Y., Qin, Y., Poprawe, R., & Schleifenbaum, J. H.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2018-10
- Volume
- 155
- Pages
- 36-45
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2803390075
- Cited by
- 179
- References
- 1
- FWCI
- 8.63
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Laser additive manufacturing of Zn metal parts for biodegradable applications: Processing, formation quality and mechanical properties. https://app.cochat.ai/papers/10.1016/j.matdes.2018.05.057
- The paper
- Wen, P., Voshage, M., Jauer, L., Chen, Y., Qin, Y., Poprawe, R., & Schleifenbaum, J. H. (2018). Laser additive manufacturing of Zn metal parts for biodegradable applications: Processing, formation quality and mechanical properties. Materials & Design. https://doi.org/10.1016/j.matdes.2018.05.057
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.