The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
High-rate lithium cycling in a scalable trilayer Li-garnet-electrolyte architecture
Open accessAbstract
Abstract Solid-state lithium batteries promise to exceed the capabilities of traditional Li-ion batteries in safety and performance. However, a number of obstacles have stood in the path of solid-state battery development, primarily high resistance and low capacity. In this work, these barriers are overcome through the fabrication of a uniquely microstructured solid electrolyte architecture based on a doped Li7La3Zr2O12 (LLZ) ceramic Li-conductor. Specifically, a porous-dense-porous trilayer structure was fabricated by tape casting, a scalable roll-to-roll manufacturing technique. The dense (>99%) center layer can be fabricated as thin as ∼10 μm and blocks dendrites over hundreds of cycles. The microstructured porous layers serve as electrode supports and increase the mechanical strength by ∼9×, making the cells strong enough to handle with ease. Additionally, the porous layers multiply the electrode–electrolyte interfacial surface area by >40× compared to a typical planar interface. Lithium symmetric cells based on the trilayer architecture were cycled at room temperature and achieved area-specific resistances (∼7 Ω-cm2) dramatically lower, and current densities dramatically higher (10 mA/cm2), than previously reported literature results. Moreover, to demonstrate scalability a large-format cell was fabricated with lithium metal in one porous layer and a sulfur electrode with conductive carbon and an ionic liquid interface in the other, achieving 1244 mAh/g S utilization and 195 Wh/kg based on total cell mass, showing a promising path to commercially viable, intrinsically safe lithium batteries with high specific energy and high energy density.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Issues and challenges facing rechargeable lithium batteries
Tarascon, J.-M., & Armand, M. (2001) · Nature · doi:10.1038/35104644 · Cited by 21,130
Electrical energy storage for the grid: A battery of choices
Dunn, B., Kamath, H., & Tarascon, J.-M. (2011) · Science · doi:10.1126/science.1212741 · Cited by 15,072
Nonaqueous Liquid Electrolytes for Lithium-Based Rechargeable Batteries
Xu, K. (2004) · Chemical Reviews · doi:10.1021/cr030203g · Cited by 7,437
Electrolytes and Interphases in Li-Ion Batteries and Beyond
Xu, K. (2014) · Chemical Reviews · doi:10.1021/cr500003w · Cited by 5,566
Fast Lithium Ion Conduction in Garnet‐Type Li7La3Zr2O12
Murugan, R., Thangadurai, V., & Weppner, W. (2007) · Angewandte Chemie International Edition · doi:10.1002/anie.200701144 · Cited by 3,250
Thermal runaway caused fire and explosion of lithium ion battery
Wang, Q., Ping, P., Zhao, X., Chu, G., Sun, J., & Chen, C. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.02.038 · Cited by 3,103
Lowering the Temperature of Solid Oxide Fuel Cells
Wachsman, E. D., & Lee, K. T. (2011) · Science · doi:10.1126/science.1204090 · Cited by 2,554
Self-citationPolysulfide Shuttle Study in the Li/S Battery System
Mikhaylik, Y. V., & Akridge, J. R. (2004) · Journal of The Electrochemical Society · doi:10.1149/1.1806394 · Cited by 2,115
Albertus, P., Babinec, S., Litzelman, S., & Newman, A. (2017) · Nature Energy · doi:10.1038/s41560-017-0047-2 · Cited by 1,888
Rapidly falling costs of battery packs for electric vehicles
Nykvist, B., & Nilsson, M. (2015) · Nature Climate Change · doi:10.1038/nclimate2564 · Cited by 1,819
A review of conduction phenomena in Li-ion batteries
Park, M., Zhang, X., Chung, M., Less, G. B., & Sastry, A. M. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.06.060 · Cited by 1,627
Progress and prospective of solid-state lithium batteries
Takada, K. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.10.034 · Cited by 1,056
Thermodynamic analysis on energy densities of batteries
Zu, C.-X., & Li, H. (2011) · Energy & Environmental Science · doi:10.1039/c0ee00777c · Cited by 911
Novel Fast Lithium Ion Conduction in Garnet‐Type Li 5 La 3 M 2 O 12 (M = Nb, Ta)
Thangadurai, V., Kaack, H., & Weppner, W. J. F. (2003) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.2003.tb03318.x · Cited by 786
Review—Practical Challenges Hindering the Development of Solid State Li Ion Batteries
Kerman, K., Luntz, A., Viswanathan, V., Chiang, Y.-M., & Chen, Z. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.1571707jes · Cited by 712
Intergranular Li metal propagation through polycrystalline Li6.25Al0.25La3Zr2O12 ceramic electrolyte
Cheng, E. J., Sharafi, A., & Sakamoto, J. S. (2016) · Electrochimica Acta · doi:10.1016/j.electacta.2016.12.018 · Cited by 708
Transition from Superlithiophobicity to Superlithiophilicity of Garnet Solid-State Electrolyte
Luo, W., Gong, Y., Zhu, Y., Fu, K. K., Dai, J., Lacey, S. D., Wang, C., Liu, B., Han, X., Mo, Y., et al. (2016) · Journal of the American Chemical Society · doi:10.1021/jacs.6b06777 · Cited by 671
Self-citationHigh lithium ionic conductivity in the garnet-type oxide Li7−X La3(Zr2−X, NbX)O12 (X=0–2)
Ohta, S., Kobayashi, T., & Asaoka, T. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.11.089 · Cited by 665
Sharifi, T., Larsen, C., Wang, J., Kwong, W. L., Gracia‐Espino, E., Mercier, G., Messinger, J., Wågberg, T., & Edman, L. (2016) · Advanced Energy Materials · doi:10.1002/aenm.201600738 · Cited by 639
Metal–Sulfur Battery Cathodes Based on PAN–Sulfur Composites
Wei, S., Ma, L., Hendrickson, K. E., Tu, Z., & Archer, L. A. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b08113 · Cited by 579
Cheng, L., Crumlin, E. J., Chen, W., Qiao, R., Hou, H., Franz Lux, S., Zorba, V., Russo, R., Kostecki, R., Liu, Z., et al. (2014) · Phys. Chem. Chem. Phys. · doi:10.1039/c4cp02921f · Cited by 545
Novel Fast Lithium Ion Conduction in Garnet‐Type Li5La3M2O12 (M: Nb, Ta).
Thangadurai, V., Kaack, H., & Weppner, W. J. F. (2003) · ChemInform · doi:10.1002/chin.200327009 · Cited by 510
Lithium batteries: To the limits of lithium
Evarts, E. C. (2015) · Nature · doi:10.1038/526s93a · Cited by 501
A critical review on lithium–air battery electrolytes
Balaish, M., Kraytsberg, A., & Ein-Eli, Y. (2014) · Physical Chemistry Chemical Physics · doi:10.1039/c3cp54165g · Cited by 454
Ohta, S., Komagata, S., Seki, J., Saeki, T., Morishita, S., & Asaoka, T. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.02.073 · Cited by 399
Will We Ever Stop Using Fossil Fuels?
Covert, T., Greenstone, M., & Knittel, C. R. (2016) · Journal of Economic Perspectives · doi:10.1257/jep.30.1.117 · Cited by 304
A Review on Li-S Batteries as a High Efficiency Rechargeable Lithium Battery
Barghamadi, M., Kapoor, A., & Wen, C. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.096308jes · Cited by 299
Modeling the performance and cost of lithium-ion batteries for electric-drive vehicles.
Nelson, P., Gallagher, K., Bloom, I., & Dees, D. (2011) · doi:10.2172/1027714 · Cited by 238
Yi, E., Wang, W., Kieffer, J., & Laine, R. M. (2016) · Journal of Materials Chemistry A · doi:10.1039/c6ta04492a · Cited by 178
A Comparative Testing Study of Commercial 18650-Format Lithium-Ion Battery Cells
Müenzel, V., Hollenkamp, A. F., Bhatt, A. I., de Hoog, J., Brazil, M., Thomas, D. A., & Mareels, I. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0721508jes · Cited by 118
Thigh burns from exploding e-cigarette lithium ion batteries: First case series
Nicoll, K., Rose, A., Khan, M. A. A., Quaba, O., & Lowrie, A. G. (2016) · Burns · doi:10.1016/j.burns.2016.03.027 · Cited by 65
Mankowski, P. J., Kanevsky, J., Bakirtzian, P., & Cugno, S. (2016) · Burns · doi:10.1016/j.burns.2015.10.012 · Cited by 54
Liu, K., & Wang, C. (2014) · Electrochemistry Communications · doi:10.1016/j.elecom.2014.09.006 · Cited by 33
Extreme La Niña events to increase
Capotondi, A. M. (2015) · Nature Climate Change · doi:10.1038/nclimate2509 · Cited by 21
Cited by
Fundamentals of inorganic solid-state electrolytes for batteries
Famprikis, T., Canepa, P., Dawson, J. A., Islam, M. S., & Masquelier, C. (2019) · Nature Materials · doi:10.1038/s41563-019-0431-3 · Cited by 2,525
Challenges and opportunities towards fast-charging battery materials
Liu, Y., Zhu, Y., & Cui, Y. (2019) · Nature Energy · doi:10.1038/s41560-019-0405-3 · Cited by 1,781
Garnet-Type Solid-State Electrolytes: Materials, Interfaces, and Batteries
Wang, C., Fu, K., Kammampata, S. P., McOwen, D. W., Samson, A. J., Zhang, L., Hitz, G. T., Nolan, A. M., Wachsman, E. D., Mo, Y., et al. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00427 · Cited by 1,212
Self-citationPhysicochemical Concepts of the Lithium Metal Anode in Solid-State Batteries
Krauskopf, T., Richter, F. H., Zeier, W. G., & Janek, J. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00431 · Cited by 892
Kim, K. J., Balaish, M., Wadaguchi, M., Kong, L., & Rupp, J. L. M. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202002689 · Cited by 806
Metadata
- Authors
- Hitz, G. T., McOwen, D. W., Zhang, L., Ma, Z., Fu, Z., Wen, Y., Gong, Y., Dai, J., Hamann, T. R., Hu, L., & Wachsman, E. D.
- Venue
- Materials Today
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 22
- Pages
- 50-57
- ISSN
- 1369-7021 (ISSN-L)
- OpenAlex
- W2806226852
- Cited by
- 318
- References
- 34
- FWCI
- 12.42
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.