The DOI matches its Crossref record.
Effect of hot isostatic pressing on the microstructure and mechanical properties of additive manufactured AlxCoCrFeNi high entropy alloys
Open accessAbstract
Abstract Three high entropy alloys (HEAs), based on the AlxCoCrFeNi alloy system have been prepared by direct laser fabrication (DLF) with aluminium molar fractions (x) of 0.3, 0.6 and 0.85. These three alloys had FCC, duplex FCC + BCC, and BCC crystal structures, respectively. The effect of hot isostatic pressing (HIP) on alloy density, microstructure and mechanical properties of these DLF bulk high entropy alloys was studied for the first time. HIP was found to decrease the number of large pores (> 5 µm) in the as-deposited alloys, which equated to a marginal increase in density. HIP also induced microstructural coarsening, chemical homogenisation and resulted in a general improvement in the mechanical properties of FCC HEA (x = 0.3). HIP improved the compressive properties of the dual phase HEA (x = 0.6), however, degraded the tensile properties as a result of the coarsening of hard BCC grain boundary precipitates. The mechanical properties were compromised in the high aluminium (x = 0.85) HEA due to the formation of σ-phase at the phase and grain boundaries, which induced a brittle fracture in tension and compression. A continuous cooling transformation (CCT) diagram for the σ-phase was determined by a dilatometric method and the critical cooling rate to inhibit σ-phase formation was found to be 1 K/s.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Recent Advances on High‐Entropy Alloys for 3D Printing
Han, C., Fang, Q., Shi, Y., Tor, S. B., Chua, C. K., & Zhou, K. (2020) · Advanced Materials · doi:10.1002/adma.201903855 · Cited by 486
Additive manufacturing of high entropy alloys: A practical review
Ostovari Moghaddam, A., Shaburova, N. A., Samodurova, M. N., Abdollahzadeh, A., & Trofimov, E. A. (2021) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2020.11.029 · Cited by 474
Al-Maharma, A. Y., Patil, S. P., & Markert, B. (2020) · Materials Research Express · doi:10.1088/2053-1591/abcc5d · Cited by 404
Additive Manufacturing of High-Entropy Alloys: A Review
Chen, S., Tong, Y., & Liaw, P. K. (2018) · Entropy · doi:10.3390/e20120937 · Cited by 257
Post-Process Treatments for Additive-Manufactured Metallic Structures: A Comprehensive Review
Ge, J., Pillay, S., & Ning, H. (2023) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-023-08051-9 · Cited by 157
Metadata
- Authors
- Joseph, J., Hodgson, P., Jarvis, T., Wu, X., Stanford, N., & Fabijanic, D. M.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2018-08
- Volume
- 733
- Pages
- 59-70
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2883441668
- Cited by
- 188
- References
- 0
- FWCI
- 7.35
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of hot isostatic pressing on the microstructure and mechanical properties of additive manufactured AlxCoCrFeNi high entropy alloys. https://app.cochat.ai/papers/10.1016/j.msea.2018.07.036
- The paper
- Joseph, J., Hodgson, P., Jarvis, T., Wu, X., Stanford, N., & Fabijanic, D. M. (2018). Effect of hot isostatic pressing on the microstructure and mechanical properties of additive manufactured AlxCoCrFeNi high entropy alloys. Materials Science and Engineering: A. https://doi.org/10.1016/j.msea.2018.07.036
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.