The DOI matches its Crossref record; 230 of the 230 references it cites were found in a registry or an index.
Ash formation and deposition in coal and biomass fired combustion systems: Progress and challenges in the field of ash particle sticking and rebound behavior
Open accessAbstract
The purpose of this paper is to review the present knowledge on ash formation, ash particle transport and deposition during solid fuel combustion, with emphasis on particle sticking and rebound behavior. A substantial part of the fuel can be inorganic, forming inorganic vapors and ash particles. The impaction of solid, molten or partially molten particles on surfaces is dependent on the particle and surface characteristics. For instance, a particulate deposit might capture incoming particles or be removed due to erosion, while a molten layer will collect all impacting particles, no matter if they are sticky or not. The main properties affecting the particle stickiness are the viscosity and surface tension for silicate-rich ashes. On the contrary, the stickiness of salt-rich ashes – typical for herbaceous biomass and wood- or waste-based fuels – is often described using the liquid melt fraction. Furthermore, the particle kinetic energy and the angle of impaction, are crucial parameters. If all kinetic energy is dissipated during the impact, the particle will remain on the surface. This review presents an overview of major ash forming elements found in biomass and coal, and discusses the heterogeneity of particles’ inorganic composition. Ash transport and deposition mechanisms as well as their mathematical description are given and discussed, together with composition- and temperature-depended models for the estimation of ash particle and deposit properties. These properties are essential in order to describe the particle sticking and rebound behavior. Ash particle sticking and rebound criteria can be divided into three main groups, based on either: (1) the particle melt fraction, (2) the particle viscosity, or (3) the energy dissipation of a particle, upon impaction. Sticking criteria are presented, their required parameters are discussed and typical particle and surface properties found in combustion systems, are summarized. Eight different sticking criteria are implemented in a computational fluid dynamics code and computations are compared against measurements from an entrained flow reactor. Uniform sized soda-lime glass particles are applied instead of inhomogeneous fly ash particles, since soda-lime glass is known to behave similar to coal fly ash. Best agreement for the deposition rates on a clean tube is achieved using a criterion based on the work of Srinivasachar et al. [1] . In this model, the sticking and rebound threshold, is a function of the particle kinetic energy, the angle of impaction, and, the particle viscosity. Particularly, the particle viscosity is confirmed as a key parameter for silicate-rich ashes. It should be calculated using temperature- and composition-dependent correlations, being aware that there is a significant scattering in the results from such models and that the models are often only valid in narrow compositional ranges, and cannot be used outside these. A mechanistic model is used to explain results from glass particle experiments and their dependence on the particle kinetic energy. Therefore, the impaction process is subdivided in four steps, and the energy dissipation of each step is calculated. These theoretical considerations show that the contact angle of a molten droplet with the substrate is of minor importance, and that the majority of depositing particles are dominated by the work of deformation against viscosity, rather than surface tension effects. This review underlines the importance of the particle viscosity, and its accurate prediction for silicate-rich ashes. The proposed criterion is able to predict the sticking of small, solid particles below 10 µm diameter, as it is often observed in literature. Also, it is crucial to consider the surface structure and stickiness, in order to predict deposition rates in solid fuel-fired systems. Biomass ashes and their stickiness are more difficult, due to a different ash particle chemistry, compared to coal ashes. Salt-rich particles and their stickiness are controlled by the amount of liquid phase. Here, a link between the viscosity and amount of liquid phase is a promising approach, and should be addressed in future work. Furthermore, the viscosity of different ash particles – silicate-, salt- or Ca-rich – should preferentially be modeled from the chemical and physical structure instead of an empirical fitting procedure between fuel chemistry and viscosity measurements.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Items 201–230 of 230
The adhesion of particles upon impaction
Esmen, N. A., Ziegler, P., & Whitfield, R. (1978) · Journal of Aerosol Science · doi:10.1016/0021-8502(78)90020-4 · Cited by 43
Formation of condensation aerosols under rapidly changing environmental conditions
Sutugin, A. G., & Fuchs, N. A. (1970) · Journal of Aerosol Science · doi:10.1016/0021-8502(70)90002-9 · Cited by 42
Yang, X., Ingham, D. B., Ma, L., Williams, A., & Pourkashanian, M. M. (2015) · Fuel · doi:10.1016/j.fuel.2015.10.056 · Cited by 42
Costa, F. F., Wang, G., & Costa, M. (2014) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2014.06.024 · Cited by 41
An experimental study of the inertial deposition of ash under coal combustion conditions
Srinivasachar, S., Helble, J. J., & Boni, A. A. (1991) · Symposium (International) on Combustion · doi:10.1016/s0082-0784(06)80394-2 · Cited by 41
Combustion of biomass in jet flames
Weber, R., Poyraz, Y., Beckmann, A. M., & Brinker, S. (2014) · Proceedings of the Combustion Institute · doi:10.1016/j.proci.2014.06.033 · Cited by 39
Rosner, D. E., & Tandon, P. (1995) · Chemical Engineering Science · doi:10.1016/0009-2509(95)00161-w · Cited by 38
Discussion about the thermal rebound of nanoparticles
Mouret, G., Chazelet, S., Thomas, D., & Bémer, D. (2011) · Separation and Purification Technology · doi:10.1016/j.seppur.2011.01.016 · Cited by 37
Brunner, T., Fluch, J., Obernberger, I., & Warnecke, R. (2011) · Fuel Processing Technology · doi:10.1016/j.fuproc.2011.04.036 · Cited by 35
Taha, T. J., Stam, A. F., Stam, K., & Brem, G. (2013) · Fuel Processing Technology · doi:10.1016/j.fuproc.2013.03.042 · Cited by 34
Experimental Studies on the Normal Impact of Fly Ash Particles with Planar Surfaces
Dong, M., Li, S., Xie, J., & Han, J. (2013) · Energies · doi:10.3390/en6073245 · Cited by 33
Walsh, P. M., & Li, T. (1994) · Combustion and Flame · doi:10.1016/0010-2180(94)90070-1 · Cited by 32
Akbar, S., Schnell, U., & Scheffknecht, G. (2010) · Combustion Theory and Modelling · doi:10.1080/13647830.2010.483019 · Cited by 30
Babat, S., Spörl, R., Maier, J., & Scheffknecht, G. (2015) · Fuel Processing Technology · doi:10.1016/j.fuproc.2015.10.001 · Cited by 29
CFD simulation of ash deposit formation in fixed bed biomass furnaces and boilers
Forstner, M., Hofmeister, G., Jöller, M., Dahl, J., Braun, M., Kleditzsch, S., Scharler, R., & Obernberger, I. (2006) · Progress in Computational Fluid Dynamics An International Journal · doi:10.1504/pcfd.2006.010034 · Cited by 29
Sodium/ash reactions in the formation of fireside deposits in pulverized-fuel-fired boilers
Boow, J. (1972) · Fuel · doi:10.1016/0016-2361(72)90074-9 · Cited by 28
Moza, A. K., & Austin, L. G. (1981) · Fuel · doi:10.1016/0016-2361(81)90049-1 · Cited by 27
Kleinhans, U., Rück, R., Schmid, S., Haselsteiner, T., & Spliethoff, H. (2016) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b01658 · Cited by 26
Self-citationRole of the Pore Structure in the Fragmentation of Highly Porous Char Particles
Kantorovich, I. I. (1998) · Combustion and Flame · doi:10.1016/s0010-2180(97)00247-2 · Cited by 23
Troiano, M., Montagnaro, F., Salatino, P., & Solimene, R. (2017) · Fuel · doi:10.1016/j.fuel.2017.08.044 · Cited by 23
Kreutzkam, B., Wieland, C. M., & Spliethoff, H. (2012) · Fuel · doi:10.1016/j.fuel.2012.02.056 · Cited by 22
Self-citationFly ash particle formation in kraft recovery boilers
Publications, V., & Mikkanen, P. (2000) · Cited by 22
Bildung und Eigenschaften von Aerosolen aus Holzfeuerungen
Nussbaumer, T., & Hasler, P. (1999) · European Journal of Wood and Wood Products · doi:10.1007/pl00002614 · Cited by 18
Influence of Segregated Mineral Matter in Coal on Slagging
Bryers, R. (1986) · ACS symposium series · doi:10.1021/bk-1986-0301.ch025 · Cited by 16
Cameron, J. H., & Goerg, K. A. (1999) · Fuel Processing Technology · doi:10.1016/s0378-3820(99)00025-9 · Cited by 15
ABBOTT, M., CONN, R., & Austin, L. G. (1985) · Fuel · doi:10.1016/0016-2361(85)90018-3 · Cited by 15
Computational simulation of aerosol behaviour
Pyykönen, J. (2002) · Aaltodoc (Aalto University) · Cited by 11
Evaluation of Particle Fragmentation of Raw and Torrified Biomass in a Drop Tube Furnace
Costa, F. F., & Costa, M. (2015) · Energy Procedia · doi:10.1016/j.egypro.2015.02.056 · Cited by 9
Schulze, K., Scharler, R., Telian, M., & Obernberger, I. (2010) · Cited by 8
Cited by
Ma, W., Wenga, T., Frandsen, F. J., Yan, B., & Chen, G. (2020) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2019.100789 · Cited by 275
Self-citationYang, W., Pudasainee, D., Gupta, R., Li, W., Wang, B., & Sun, L. (2021) · Fuel Processing Technology · doi:10.1016/j.fuproc.2020.106657 · Cited by 235
Critical review of the role of ash content and composition in biomass pyrolysis
Puri, L., Hu, Y., & Naterer, G. (2024) · Frontiers in Fuels · doi:10.3389/ffuel.2024.1378361 · Cited by 226
A review of biomass ash related problems: Mechanism, solution, and outlook
Abioye, K. J., Harun, N. Y., Sufian, S., Yusuf, M., Jagaba, A. H., Ekeoma, B. C., Kamyab, H., Sikiru, S., Waqas, S., & Ibrahim, H. (2024) · Journal of the Energy Institute · doi:10.1016/j.joei.2023.101490 · Cited by 135
Fine Ash-Bearing Particles as a Major Aerosol Component in Biomass Burning Smoke
Adachi, K., Dibb, J. E., Scheuer, E., Katich, J. M., Schwarz, J. P., Perring, A. E., Mediavilla, B., Guo, H., Campuzano‐Jost, P., Jimenez, J. L., et al. (2022) · Journal of Geophysical Research: Atmospheres · doi:10.1029/2021jd035657 · Cited by 55
Metadata
- Authors
- Kleinhans, U., Wieland, C., Frandsen, F. J., & Spliethoff, H.
- Venue
- Progress in Energy and Combustion Science
- Publisher
- Elsevier BV
- Published
- 2018-09
- Volume
- 68
- Pages
- 65-168
- ISSN
- 0360-1285 (ISSN-L)
- OpenAlex
- W2803470089
- Cited by
- 487
- References
- 230
- FWCI
- 16.33
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.