The DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index.
Discrete element simulation and experimental study of powder spreading process in additive manufacturing
Open accessAbstract
Powders used in additive manufacturing (AM) are spread onto a compact layer of particles for sintering and this process is repeated layer by layer to form the final products. Spreading of rod-shaped particles in realistic AM settings is simulated using the discrete element method (DEM) to investigate the effects of particle shape and operating conditions on the bed quality, characterised by its surface roughness and solid volume fraction. It is discovered that larger particle aspect ratios, A r , or higher spreader translational velocities result in a lower bed quality, i.e. a larger surface roughness and a smaller volume fraction. The surface roughness increases monotonically with A r . However, the volume fraction exhibits a maximum at A r = 1.5 for randomly packed powder beds that are formed by the roller type spreaders moving at low translational velocities. It is also found that a roller outperforms a blade spreader in terms of the quality of the prepared bed at the same operating conditions. The micro-structural analysis of the beds also shows particle alignment in response to the induced flow, which is qualitatively confirmed by a set of purposely-designed experiments. In addition, a shape segregation is documented for powders with mixed aspect ratios (A r ) such that particles with larger A r tend to accumulate on the upper layers of the bed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
NIH Image to ImageJ: 25 years of image analysis
Schneider, C. A., Rasband, W. S., & Eliceiri, K. W. (2012) · Nature Methods · doi:10.1038/nmeth.2089 · Cited by 64,638
Fast Parallel Algorithms for Short-Range Molecular Dynamics
Plimpton, S. (1995) · Journal of Computational Physics · doi:10.1006/jcph.1995.1039 · Cited by 44,721
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
Comparison of contact-force models for the simulation of collisions in DEM-based granular flow codes
Di Renzo, A., & Di Maio, F. P. (2004) · Chemical Engineering Science · doi:10.1016/j.ces.2003.09.037 · Cited by 1,127
Assessment of rolling resistance models in discrete element simulations
Ai, J., Chen, J.-F., Rotter, J. M., & Ooi, J. Y. (2011) · Powder Technology · doi:10.1016/j.powtec.2010.09.030 · Cited by 1,073
Rolling friction in the dynamic simulation of sandpile formation
Zhou, Y. C., Wright, B. D., Yang, R. Y., Xu, B. H., & Yu, A. B. (1999) · Physica A: Statistical Mechanics and its Applications · doi:10.1016/s0378-4371(99)00183-1 · Cited by 717
Force Schemes in Simulations of Granular Materials
Shäfer, J., Dippel, S., & Wolf, D. E. (1996) · Journal de Physique I · doi:10.1051/jp1:1996129 · Cited by 694
Distribution of directional data and fabric tensors
Ken-Ichi, K. (1984) · International Journal of Engineering Science · doi:10.1016/0020-7225(84)90090-9 · Cited by 663
A review of rapid prototyping technologies and systems
Yan, X., & Gu, P. (1996) · Computer-Aided Design · doi:10.1016/0010-4485(95)00035-6 · Cited by 565
Extrusion-based additive manufacturing of PEEK for biomedical applications
Vaezi, M., & Yang, S. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1097053 · Cited by 406
Cited by
Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
Mostafaei, A., Elliott, A. M., Barnes, J. E., Li, F., Tan, W., Cramer, C. L., Nandwana, P., & Chmielus, M. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100707 · Cited by 1,093
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
A review of powder additive manufacturing processes for metallic biomaterials
Harun, W. S. W., Kamariah, M. S. I. N., Muhamad, N., Ghani, S. A. C., Ahmad, F., & Mohamed, Z. (2018) · Powder Technology · doi:10.1016/j.powtec.2017.12.058 · Cited by 379
Metal Binder Jetting Additive Manufacturing: A Literature Review
Li, M., Du, W., Elwany, A., Pei, Z., & Ma, C. (2020) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4047430 · Cited by 334
Metadata
- Authors
- Haeri, S., Wang, Y., Ghita, O., & Sun, J.
- Venue
- Powder Technology
- Publisher
- Elsevier BV
- Published
- 2017-01
- Volume
- 306
- Pages
- 45-54
- ISSN
- 0032-5910 (ISSN-L)
- OpenAlex
- W2556330383
- Cited by
- 322
- References
- 19
- FWCI
- 14.39
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Discrete element simulation and experimental study of powder spreading process in additive manufacturing. https://app.cochat.ai/papers/10.1016/j.powtec.2016.11.002
- The paper
- Haeri, S., Wang, Y., Ghita, O., & Sun, J. (2017). Discrete element simulation and experimental study of powder spreading process in additive manufacturing. Powder Technology. https://doi.org/10.1016/j.powtec.2016.11.002
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.