Effect of inclination on the air-side performance of a brazed aluminum heat exchanger under dry and wet conditions
Integrity signals
Registry
Cites
Statistics
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The inclination angle increases the air-side pressure drop of MCHX, and the pressure drop increases with the inclination angle.
“According to the above-reported researches, the inclination angle increases the air-side pressure drop of MCHX, and the pressure drop increases with the inclination angle.”
For inclined MCHX, the influence of inclination angle on heat transfer coefficient is not obvious, but the air-side pressure drop increases with increasing inclination angle.
“According to the results, the influence of the inclination angle on heat transfer coefficient was not obvious, but the air-side pressure drop increased with the increase inclination angle.”
Air shear force increases with increasing wind speed, which helps remove condensate.
“Kim et al. [89] claimed that the air shear force increases with the increase of wind speed, which was helpful to remove condensate.”
Kim et al. derived a new correlation for the f factor of inclined heat exchangers based on the correlations for the referenced inclination angle.
“Also, Kim et al. [89] derived a new correlation for the f factor of inclined heat exchangers based on the correlations for the referenced inclination angle.”
Cites
Air-side thermal hydraulic performance of multi-louvered fin aluminum heat exchangers
Kim, M.-H., & Bullard, C. W. (2002) · International Journal of Refrigeration · doi:10.1016/s0140-7007(01)00025-1 · Cited by 280 · see citing works
Self-citationPrediction of Heat Transfer and Friction for the Louver Fin Geometry
Sahnoun, A., & Webb, R. L. (1992) · Journal of Heat Transfer · doi:10.1115/1.2911898 · Cited by 69 · see citing works
Flagged first, then by citations
Cited by
Sorted by citations
Ma, X., Ding, G., Zhang, Y., & Wang, K. (2007) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2007.03.001 · Cited by 82 · see citing works
Kim, M.-H., Song, S., & Bullard, C. W. (2002) · International Journal of Refrigeration · doi:10.1016/s0140-7007(01)00061-5 · Cited by 39 · see citing works
Self-citationXiong, T., Liu, G., Gao, Q., Yan, G., & Yu, J. (2023) · Journal of Building Engineering · doi:10.1016/j.jobe.2022.105654 · Cited by 26 · see citing works
Park, J.-S., Kim, J., & Lee, K.-S. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.01.043 · Cited by 24 · see citing works
- Authors
- Kim, M.-H., Youn, B., & Bullard, C. W.
- Affiliations
- University of Illinois Urbana-Champaign (US)
- Samsung (South Korea) (KR)
- Corresponding author
- Kim, Man-Hoe
- Venue
- International Journal of Heat and Mass Transfer
- Publisher
- Elsevier BV
- Published
- 2001-12
- Volume
- 44
- Issue
- 24
- Pages
- 4613-4623
- ISSN
- 0017-9310 (ISSN-L)
- OpenAlex
- W1973731366
- Cited by
- 52
- References
- 2
- Citations by year
- 2026: 2 · 2025: 3 · 2024: 1 · 2023: 1 · 2022: 2 · 2021: 2 · 2020: 1 · 2019: 3 · 2018: 3 · 2017: 2 · 2016: 1 · 2015: 3 · 2014: 2 · 2013: 4
- FWCI
- 10.23
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- International Journal of Heat and Mass Transfer (publishedVersion)
- Funders
- Samsung
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Optimization
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer Mechanisms
- Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Boiling Studies
- Keywords
- flat tube heat exchanger, wet conditions, condensate drainage, pressure drop, heat transfer coefficient, finned tube heat exchanger
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
