The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Laser-Induced Graphene
Abstract
Conspectus Research on graphene abounds, from fundamental science to device applications. In pursuit of complementary morphologies, formation of graphene foams is often preferred over the native two-dimensional (2D) forms due to the higher available area. Graphene foams have been successfully prepared by several routes including chemical vapor deposition (CVD) methods and by wet-chemical approaches. For these methods, one often needs either high temperature furnaces and highly pure gases or large amounts of strong acids and oxidants. In 2014, using a commercial laser scribing system as found in most machine shops, a direct lasing of polyimide (PI) plastic films in the air converted the PI into 3D porous graphene, a material termed laser-induced graphene (LIG). This is a one-step method without the need for high-temperature reaction conditions, solvent, or subsequent treatments, and it affords graphene with many five-and seven-membered rings. With such an atomic arrangement, one might call LIG “kinetic graphene” since there is no annealing in the process that causes the rearrangement to the preferred all-six-membered-ring form. In this Account, we will first introduce the approaches that have been developed for making LIG and to control the morphology as either porous sheets or fibrils, and to control porosity, composition, and surface properties. The surfaces can be varied from being either superhydrophilic with a 0° contact angle with water to being superhydrophobic having >150° contact angle with water. While it was initially thought that the LIG process could only be performed on PI, it was later shown that a host of other polymeric substrates, nonpolymers, metal/plastic composites, and biodegradable and naturally occurring materials and foods could be used as platforms for generating LIG. Methods of preparation include roll-to-roll production for fabrication of in-plane electronics and two different 3D printing (additive manufacturing) routes to specific shapes of LIG monoliths using both laminated object manufacturing and powder bed fabrication methods. Use of the LIG in devices is performed very simply. This is showcased with high performance supercapacitors, fuel cell materials for oxygen reduction reactions, water splitting for both hydrogen and oxygen evolution reactions coming from the same plastic sheet, sensor devices, oil/water purification platforms, and finally applications in both passive and active biofilm inhibitors. So the ease of formation of LIG, its simple scale-up, and its utility for a range of applications highlights the easy transition of this substrate-bound graphene foam into commercial device platforms.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Laser Scribing of High-Performance and Flexible Graphene-Based Electrochemical Capacitors
El-Kady, M. F., Strong, V., Dubin, S., & Kaner, R. B. (2012) · Science · doi:10.1126/science.1216744 · Cited by 4,008
Chen, Z., Ren, W., Gao, L., Liu, B., Pei, S., & Cheng, H.-M. (2011) · Nature Materials · doi:10.1038/nmat3001 · Cited by 3,834
Self-Assembled Graphene Hydrogel via a One-Step Hydrothermal Process
Xu, Y., Sheng, K., Li, C., & Shi, G. (2010) · ACS Nano · doi:10.1021/nn101187z · Cited by 3,251 · cited 2×
“4,5 However, these methods either require several fabrication steps or they can have poor control over the morphology of the printed objects.”
BackgroundMethodLaser-induced porous graphene films from commercial polymers
Lin, J., Peng, Z., Liu, Y., Ruiz-Zepeda, F., Ye, R., Samuel, E. L. G., Yacaman, M. J., Yakobson, B. I., & Tour, J. M. (2014) · Nature Communications · doi:10.1038/ncomms6714 · Cited by 2,946
Self-citationUltrahigh-power micrometre-sized supercapacitors based on onion-like carbon
Pech, D., Brunet, M., Durou, H., Huang, P., Mochalin, V., Gogotsi, Y., Taberna, P.-L., & Simon, P. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2010.162 · Cited by 2,721
Lai, L., Potts, J. R., Zhan, D., Wang, L., Poh, C. K., Tang, C., Gong, H., Shen, Z., Lin, J., & Ruoff, R. S. (2012) · Energy & Environmental Science · doi:10.1039/c2ee21802j · Cited by 2,277
El-Kady, M. F., & Kaner, R. B. (2013) · Nature Communications · doi:10.1038/ncomms2446 · Cited by 1,868
3D Macroporous Graphene Frameworks for Supercapacitors with High Energy and Power Densities
Choi, B. G., Yang, M., Hong, W. H., Choi, J. W., & Huh, Y. S. (2012) · ACS Nano · doi:10.1021/nn3003345 · Cited by 1,286
Waltzing with the Versatile Platform of Graphene to Synthesize Composite Photocatalysts
Zhang, N., Yang, M.-Q., Liu, S., Sun, Y., & Xu, Y.-J. (2015) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00267 · Cited by 1,135
“Green” electronics: biodegradable and biocompatible materials and devices for sustainable future
Irimia-Vladu, M. (2014) · Chem. Soc. Rev. · doi:10.1039/c3cs60235d · Cited by 1,044
Laser-Induced Graphene by Multiple Lasing: Toward Electronics on Cloth, Paper, and Food
Chyan, Y., Ye, R., Li, Y., Singh, S. P., Arnusch, C. J., & Tour, J. M. (2018) · ACS Nano · doi:10.1021/acsnano.7b08539 · Cited by 1,033
Self-citationValue-adding to cellulosic ethanol: Lignin polymers
Doherty, W. O. S., Mousavioun, P., & Fellows, C. M. (2011) · Industrial Crops and Products · doi:10.1016/j.indcrop.2010.10.022 · Cited by 978
Wu, Z.-S., Ren, W., Gao, L., Zhao, J., Chen, Z., Liu, B., Tang, D., Yu, B., Jiang, C., & Cheng, H.-M. (2009) · ACS Nano · doi:10.1021/nn900020u · Cited by 937
Qiu, B., Xing, M., & Zhang, J. (2014) · Journal of the American Chemical Society · doi:10.1021/ja500873u · Cited by 777
Flexible Boron-Doped Laser-Induced Graphene Microsupercapacitors
Peng, Z., Ye, R., Mann, J. A., Zakhidov, D., Li, Y., Smalley, P. R., Lin, J., & Tour, J. M. (2015) · ACS Nano · doi:10.1021/acsnano.5b00436 · Cited by 712
Self-citationSuperior Micro‐Supercapacitors Based on Graphene Quantum Dots
Liu, W., Feng, Y., Yan, X., Chen, J., & Xue, Q. (2013) · Advanced Functional Materials · doi:10.1002/adfm.201203771 · Cited by 711
Laser‐Induced Graphene Formation on Wood
Ye, R., Chyan, Y., Zhang, J., Li, Y., Han, X., Kittrell, C., & Tour, J. M. (2017) · Advanced Materials · doi:10.1002/adma.201702211 · Cited by 665
Self-citationHigh‐Performance Pseudocapacitive Microsupercapacitors from Laser‐Induced Graphene
Li, L., Zhang, J., Peng, Z., Li, Y., Gao, C., Ji, Y., Ye, R., Kim, N. D., Zhong, Q., Yang, Y., et al. (2016) · Advanced Materials · doi:10.1002/adma.201503333 · Cited by 571
Self-citationAn intelligent artificial throat with sound-sensing ability based on laser induced graphene
Tao, L.-Q., Tian, H., Liu, Y., Ju, Z.-Y., Pang, Y., Chen, Y.-Q., Wang, D.-Y., Tian, X.-G., Yan, J.-C., Deng, N.-Q., et al. (2017) · Nature Communications · doi:10.1038/ncomms14579 · Cited by 558
Duy, L. X., Peng, Z., Li, Y., Zhang, J., Ji, Y., & Tour, J. M. (2018) · Carbon · doi:10.1016/j.carbon.2017.10.036 · Cited by 503
Self-citationFlexible and Stackable Laser-Induced Graphene Supercapacitors
Peng, Z., Lin, J., Ye, R., Samuel, E. L. G., & Tour, J. M. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/am509065d · Cited by 470
Self-citationLaser‐Induced Graphene in Controlled Atmospheres: From Superhydrophilic to Superhydrophobic Surfaces
Li, Y., Luong, D. X., Zhang, J., Tarkunde, Y. R., Kittrell, C., Sargunaraj, F., Ji, Y., Arnusch, C. J., & Tour, J. M. (2017) · Advanced Materials · doi:10.1002/adma.201700496 · Cited by 405
Self-citationHighly Stretchable and Sensitive Unidirectional Strain Sensor via Laser Carbonization
Rahimi, R., Ochoa, M., Yu, W., & Ziaie, B. (2015) · ACS Applied Materials & Interfaces · doi:10.1021/am509087u · Cited by 400
Luo, S., Hoang, P. T., & Liu, T. (2016) · Carbon · doi:10.1016/j.carbon.2015.09.076 · Cited by 295
Highly Efficient Laser Scribed Graphene Electrodes for On‐Chip Electrochemical Sensing Applications
Nayak, P., Kurra, N., Xia, C., & Alshareef, H. N. (2016) · Advanced Electronic Materials · doi:10.1002/aelm.201600185 · Cited by 293
In Situ Formation of Metal Oxide Nanocrystals Embedded in Laser-Induced Graphene
Ye, R., Peng, Z., Wang, T., Xu, Y., Zhang, J., Li, Y., Nilewski, L. G., Lin, J., & Tour, J. M. (2015) · ACS Nano · doi:10.1021/acsnano.5b04138 · Cited by 288
Self-citationGraphene Tribotronics for Electronic Skin and Touch Screen Applications
Khan, U., Kim, T., Ryu, H., Seung, W., & Kim, S. (2017) · Advanced Materials · doi:10.1002/adma.201603544 · Cited by 270
Xue, M., Li, F., Zhu, J. H., Song, H., Zhang, M., & Cao, T. (2012) · Advanced Functional Materials · doi:10.1002/adfm.201101989 · Cited by 262
Laminated Object Manufacturing of 3D‐Printed Laser‐Induced Graphene Foams
Luong, D. X., Subramanian, A. K., Silva, G. A. L., Yoon, J., Cofer, S., Yang, K., Owuor, P. S., Wang, T., Wang, Z., Lou, J., et al. (2018) · Advanced Materials · doi:10.1002/adma.201707416 · Cited by 257
Self-citationThree-Dimensional Printed Graphene Foams
Sha, J., Li, Y., Villegas Salvatierra, R., Wang, T., Dong, P., Ji, Y., Lee, S.-K., Zhang, C., Zhang, J., Smith, R. H., et al. (2017) · ACS Nano · doi:10.1021/acsnano.7b01987 · Cited by 214
Self-citationDong, Y., Rismiller, S. C., & Lin, J. (2016) · Carbon · doi:10.1016/j.carbon.2016.03.050 · Cited by 187
Tan, K. W., Jung, B., Werner, J. G., Rhoades, E. R., Thompson, M. O., & Wiesner, U. (2015) · Science · doi:10.1126/science.aab0492 · Cited by 175
Efficient Water-Splitting Electrodes Based on Laser-Induced Graphene
Zhang, J., Zhang, C., Sha, J., Fei, H., Li, Y., & Tour, J. M. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b06727 · Cited by 152
Self-citationLaser-Induced Conversion of Teflon into Fluorinated Nanodiamonds or Fluorinated Graphene
Ye, R., Han, X., Kosynkin, D. V., Li, Y., Zhang, C., Jiang, B., Martí, A. A., & Tour, J. M. (2018) · ACS Nano · doi:10.1021/acsnano.7b05877 · Cited by 123
Self-citationHigh Performance Electrocatalytic Reaction of Hydrogen and Oxygen on Ruthenium Nanoclusters
Ye, R., Liu, Y., Peng, Z., Wang, T., Jalilov, A. S., Yakobson, B. I., Wei, S., & Tour, J. M. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b15725 · Cited by 120
Self-citationKumar, M. P., Raju, M. M., Asokan, A., Selvaraj, S., Kalita, G., Narayanan, T. N., Sahu, A. K., & Pattanayak, D. K. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.0541608jes · Cited by 102
Monolithic and Flexible ZnS/SnO 2 Ultraviolet Photodetectors with Lateral Graphene Electrodes
Zhang, C., Xie, Y., Deng, H., Tumlin, T. M., Zhang, C., Su, J., Yu, P., & Lin, J. (2017) · Small · doi:10.1002/smll.201604197 · Cited by 88
Cited by
A laser-engraved wearable sensor for sensitive detection of uric acid and tyrosine in sweat
Yang, Y., Song, Y., Bo, X., Min, J., Pak, O. S., Zhu, L., Wang, M., Tu, J., Kogan, A., Zhang, H., et al. (2020) · Nature Biotechnology · doi:10.1038/s41587-019-0321-x · Cited by 1,270
3D Graphene Materials: From Understanding to Design and Synthesis Control
Sun, Z., Fang, S., & Hu, Y. H. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00083 · Cited by 543
Laser Fabrication of Graphene‐Based Flexible Electronics
You, R., Liu, Y., Hao, Y., Han, D., Zhang, Y., & You, Z. (2020) · Advanced Materials · doi:10.1002/adma.201901981 · Cited by 542
Printed supercapacitors: materials, printing and applications
Zhang, Y.-Z., Wang, Y., Cheng, T., Yao, L.-Q., Li, X., Lai, W.-Y., & Huang, W. (2019) · Chemical Society Reviews · doi:10.1039/c7cs00819h · Cited by 497
Shao, Y., Ying, Y., & Ping, J. (2020) · Chemical Society Reviews · doi:10.1039/c9cs00587k · Cited by 472
Metadata
- Authors
- Ye, R., James, D. K., & Tour, J. M.
- Venue
- Accounts of Chemical Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2018-06-20
- Volume
- 51
- Issue
- 7
- Pages
- 1609-1620
- ISSN
- 0001-4842 (ISSN-L)
- 1520-4898
- OpenAlex
- W4236825273
- Cited by
- 795
- References
- 37
- FWCI
- 19.34
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.