Effect of Operating Parameters and Moisture Content on Municipal Solid Waste Pyrolysis and Gasification
Open accessThe DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index.
Abstract
Pyrolysis/gasification-based waste-to-energy (WtE) techniques, comprising partial oxidation of waste and subsequent syngas combustion, show potential benefits over direct incineration. To facilitate their development under the specific conditions of China, pyrolysis and gasification of typical municipal solid waste (MSW) are investigated in a fluidized bed reactor. The effect of the equivalence ratio (ER), reaction temperature, and moisture content on MSW conversion is studied. A rising ER increases the syngas yield but decreases the syngas heating value. The combustible gas yield is strengthened at lower ERs and later drops when the ER exceeds 0.4 as a result of the continuously enhanced oxidation reactions. A higher temperature favors pyrolysis reactions but causes an evident decrease in the syngas heating value during gasification. When the ER is at 0.4 and the temperature is at 650 °C, an optimum operating performance is obtained under the specific input simulated MSW (S-MSW) and test conditions, with an energy conversion efficiency of 68.5%. Under such a circumstance, the further increase of the MSW moisture content is effective for stimulating H 2 production; nevertheless, the quality of syngas degrades, and the energy conversion efficiency declines. The appropriate MSW moisture content is found to be lower than 20–25%. Besides, emiessions, such as heavy metals and dioxins, are also compared to conventional incineration to verify the environmental feasibility of gasification.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Review of fast pyrolysis of biomass and product upgrading
Bridgwater, A. V. (2012) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2011.01.048 · Cited by 4,856 · cited 1×
“3 It is de fi ned as the thermochemical conversion of MSW to combustible products in the absence of oxygen (pyrolysis) or in partial combustion conditions (gasi fi cation).”
BackgroundProcess and technological aspects of municipal solid waste gasification. A review
Arena, U. (2012) · Waste Management · doi:10.1016/j.wasman.2011.09.025 · Cited by 1,349
Energy production from biomass (part 3): gasification technologies
McKendry, P. (2002) · Bioresource Technology · doi:10.1016/s0960-8524(01)00120-1 · Cited by 1,248 · cited 1×
“McKendry 35 pointed out that fuel with a moisture content above 30% makes ignition di ffi cult.”
BackgroundModeling of biomass gasification in fluidized bed
Gómez-Barea, A., & Leckner, B. (2010) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2009.12.002 · Cited by 905
Biomass gasification in a circulating fluidized bed
Li, X. T., Grace, J. R., Lim, C. J., Watkinson, A. P., Chen, H. P., & Kim, J. R. (2004) · Biomass and Bioenergy · doi:10.1016/s0961-9534(03)00084-9 · Cited by 779
Narváez, I., Orío, A., Aznar, M., & Corella, J. (1996) · Industrial & Engineering Chemistry Research · doi:10.1021/ie9507540 · Cited by 637
Fundamentals, kinetics and endothermicity of the biomass pyrolysis reaction
Van de Velden, M., Baeyens, J., Brems, A., Janssens, B., & Dewil, R. (2010) · Renewable Energy · doi:10.1016/j.renene.2009.04.019 · Cited by 629
Energy from gasification of solid wastes
Belgiorno, V., De Feo, G., Della Rocca, C., & Napoli, R. M. A. (2003) · Waste Management · doi:10.1016/s0956-053x(02)00149-6 · Cited by 452
Knoef, H. (2005) · Medical Entomology and Zoology · Cited by 366
Hernández, J. J., Aranda-Almansa, G., & Bula, A. (2010) · Fuel Processing Technology · doi:10.1016/j.fuproc.2010.01.018 · Cited by 342
The effect of air preheating in a biomass CFB gasifier using ASPEN Plus simulation
Doherty, W. G., Reynolds, A., & Kennedy, D. (2009) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2009.05.004 · Cited by 331
HE, M., HU, Z., XIAO, B., LI, J., GUO, X., LUO, S., YANG, F., FENG, Y., YANG, G., & LIU, S. (2009) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2008.09.070 · Cited by 254
Air gasification of polypropylene plastic waste in fluidized bed gasifier
Xiao, R., Jin, B., Zhou, H., Zhong, Z., & Zhang, M. (2006) · Energy Conversion and Management · doi:10.1016/j.enconman.2006.09.004 · Cited by 241
Gasification of municipal solid waste in the Plasma Gasification Melting process
Zhang, Q., Dor, L., Fenigshtein, D., Yang, W., & Blasiak, W. (2011) · Applied Energy · doi:10.1016/j.apenergy.2011.01.041 · Cited by 218
Consonni, S., & Viganò, F. (2012) · Waste Management · doi:10.1016/j.wasman.2011.12.019 · Cited by 169
Niu, M., Huang, Y., Jin, B., & Wang, X. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie400026b · Cited by 163
Luo, S., Xiao, B., Hu, Z., Liu, S., Guan, Y., & Cai, L. (2010) · Bioresource Technology · doi:10.1016/j.biortech.2010.03.060 · Cited by 160
Gasification of a solid recovered fuel in a pilot scale fluidized bed reactor
Arena, U., & Gregorio, F. D. (2013) · Fuel · doi:10.1016/j.fuel.2013.09.044 · Cited by 158
Gasification characteristics of MSW and an ANN prediction model
Xiao, G., Ni, M., Chi, Y., Jin, B., Xiao, R., Zhong, Z., & Huang, Y. (2008) · Waste Management · doi:10.1016/j.wasman.2008.02.022 · Cited by 133
Self-citationThe current situation of solid waste management in China
Huang, Q., Wang, Q., Dong, L., Xi, B., & Zhou, B. (2006) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-005-0137-2 · Cited by 131 · cited 1×
“Because the moisture content of the raw MSW in China is relatively high (normally more than 40 − 50%), 34 the input MSW should be predried prior to gasi fi cation.”
BackgroundSelf-citationThermodynamic evaluation of biomass gasification with air in autothermal gasifiers
Zhang, Y., Li, B., Li, H., & Liu, H. (2011) · Thermochimica Acta · doi:10.1016/j.tca.2011.03.005 · Cited by 125
Partitioning of Heavy Metals in Municipal Solid Waste Pyrolysis, Gasification, and Incineration
Dong, J., Chi, Y., Tang, Y., Ni, M., Nzihou, A., Weiss-Hortala, E., & Huang, Q. (2015) · Energy & Fuels · doi:10.1021/acs.energyfuels.5b01918 · Cited by 105
Self-citationSimulation of municipal solid waste gasification in two different types of fixed bed reactors
Chen, C., Jin, Y., Yan, J., & Chi, Y. (2011) · Fuel · doi:10.1016/j.fuel.2011.06.075 · Cited by 103
Self-citationDonatelli, A., Iovane, P., & Molino, A. (2010) · Fuel · doi:10.1016/j.fuel.2010.03.040 · Cited by 97
Gasification of high moisture rubber woodchip with rubber waste in a bubbling fluidized bed
Kaewluan, S., & Pipatmanomai, S. (2010) · Fuel Processing Technology · doi:10.1016/j.fuproc.2010.11.026 · Cited by 97
Baggio, P., Baratieri, M., Gasparella, A., & Longo, G. A. (2007) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2007.03.028 · Cited by 86
An innovative example of herb residues recycling by gasification in a fluidized bed
Guo, F., Dong, Y., Dong, L., & Jing, Y. (2013) · Waste Management · doi:10.1016/j.wasman.2012.12.009 · Cited by 80
Li, J., Liao, S., Dan, W., Jia, K., & Zhou, X. (2012) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2012.08.026 · Cited by 76
Environmental aspects of gasification of Korean municipal solid waste in a pilot plant
Kwak, T.-H., Maken, S., Lee, S., Park, J., Min, B.-R., & Yoo, Y. D. (2006) · Fuel · doi:10.1016/j.fuel.2006.03.012 · Cited by 74
Dong, J., Ni, M., Chi, Y., Zou, D., & Fu, C. (2013) · Environmental Science and Pollution Research · doi:10.1007/s11356-013-1569-1 · Cited by 61
Self-citationGregorio, F. D., & Zaccariello, L. (2012) · Energy · doi:10.1016/j.energy.2012.03.048 · Cited by 41
Development of waste gasification and gas reforming system for municipal solid waste (MSW)
Tsuyoshi, N. O. M. A., Ide, K., Yoshikawa, J., Kojo, K., Matsui, H., Nakajima, R., & Imai, K. (2012) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-012-0051-3 · Cited by 24
Cited by
Potential of pyrolysis processes in the waste management sector
Czajczyńska, D., Anguilano, L., Ghazal, H., Krzyżyńska, R., Reynolds, A. J., Spencer, N., & Jouhara, H. (2017) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2017.06.003 · Cited by 531
Plastic waste upcycling toward a circular economy
Zhao, X., Korey, M., Li, K., Copenhaver, K., Tekinalp, H., Celik, S., Kalaitzidou, K., Ruan, R., Ragauskas, A. J., & Ozcan, S. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.131928 · Cited by 421
Municipal solid waste as a sustainable resource for energy production: State-of-the-art review
Shah, A. V., Srivastava, V. K., Mohanty, S. S., & Varjani, S. (2021) · Journal of Environmental Chemical Engineering · doi:10.1016/j.jece.2021.105717 · Cited by 288
Wet organic waste treatment via hydrothermal processing: A critical review
Marzbali, M. H., Kundu, S., Halder, P., Patel, S., Hakeem, I. G., Paz-Ferreiro, J., Madapusi, S., Surapaneni, A., & Shah, K. (2021) · Chemosphere · doi:10.1016/j.chemosphere.2021.130557 · Cited by 147
Rambhatla, N., Panicker, T. F., Mishra, R. K., Manjeshwar, S. K., & Sharma, A. (2025) · Results in Engineering · doi:10.1016/j.rineng.2024.103679 · Cited by 133
Metadata
- Authors
- Dong, J., Chi, Y., Tang, Y., Ni, M., Nzihou, A., Weiss-Hortala, E., & Huang, Q.
- Venue
- Energy & Fuels
- Publisher
- American Chemical Society (ACS)
- Published
- 2016-04-29
- Volume
- 30
- Issue
- 5
- Pages
- 3994-4001
- ISSN
- 0887-0624 (ISSN-L)
- 1520-5029
- OpenAlex
- W2342485918
- Cited by
- 158
- References
- 32
- FWCI
- 4.71
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.