Review on Reactor Configurations for Adsorption-Based CO 2 Capture
Open accessThe DOI matches its Crossref record; 112 of the 115 references it cites were found in a registry or an index.
Abstract
Adsorption-based CO2 capture has enjoyed considerable research attention in recent years. Most of the research efforts focused on sorbent development to reduce the energy penalty. However, the use of suitable gas–solid contacting systems is key for extracting the full potential from the sorbent to minimize operating and capital costs and accelerate the commercial deployment of the technology. This paper reviews several reactor configurations that were proposed for adsorption-based CO2 capture. The fundamental behavior of adsorption in different gas–solid contactors (fixed, fluidized, moving, or rotating beds) and regeneration under different modes (pressure, temperature, or combined swings) is discussed, highlighting the strengths and limitations of different combinations of gas–solid contactor and regeneration mode. In addition, the estimated energy duties in published studies and current technology readiness level of the different reactor configurations are reported. Other aspects, such as the reactor footprint, the operation strategy, suitability to retrofits, and the ability to operate under flexible loads are also discussed. In terms of future work, the key research need is a standardized techno-economic benchmarking study to calculate CO2 avoidance costs for different adsorption technologies under standardized assumptions. Qualitatively, each technology presents several strengths and weaknesses that make it impossible to identify a clear optimal solution. Such a standardized quantitative comparison is therefore needed to focus on future technology development efforts.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“It has been shown, in fact, that alternative microstructures can offer much lower pressure drops [49].”
From Topology optimisation of adsorption beds for cost-effective direct air capture (2026) · cites this paper as [49]
Citations
Cites
Carbon capture and storage (CCS): the way forward
Bui, M., Adjiman, C. S., Bardow, A., Anthony, E. J., Boston, A., Brown, S., Fennell, P. S., Fuss, S., Galindo, A., Hackett, L. A., et al. (2018) · Energy & Environmental Science · doi:10.1039/c7ee02342a · Cited by 4,374
Principles of adsorption and adsorption processes
Kast, W. (1985) · Chemical Engineering and Processing: Process Intensification · doi:10.1016/0255-2701(85)80013-1 · Cited by 2,430
Post-Combustion CO 2 Capture Using Solid Sorbents: A Review
Samanta, A., Zhao, A., Shimizu, G. K. H., Sarkar, P., & Gupta, R. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie200686q · Cited by 1,889
CO2 capture by solid adsorbents and their applications: current status and new trends
Wang, Q., Luo, J., Zhong, Z., & Borgna, A. (2011) · Energy Environ. Sci. · doi:10.1039/c0ee00064g · Cited by 1,611
Abanades, J. C., Arias, B., Lyngfelt, A., Mattisson, T., Wiley, D. E., Li, H., Ho, M. T., Mangano, E., & Brandani, S. (2015) · International Journal of Greenhouse Gas Control · doi:10.1016/j.ijggc.2015.04.018 · Cited by 441
Alkali and alkaline-earth cation exchanged chabazite zeolites for adsorption based CO2 capture
Zhang, J., Singh, R., & Webley, P. A. (2008) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2007.08.022 · Cited by 313
Structured adsorbents in gas separation processes
Rezaei, F., & Webley, P. (2010) · Separation and Purification Technology · doi:10.1016/j.seppur.2009.10.004 · Cited by 294
CO2 capture from dry flue gas by vacuum swing adsorption: A pilot plant study
Krishnamurthy, S., Rao, V. R., Guntuka, S., Sharratt, P., Haghpanah, R., Rajendran, A., Amanullah, M., Karimi, I. A., & Farooq, S. (2014) · AIChE Journal · doi:10.1002/aic.14435 · Cited by 282
Wurzbacher, J. A., Gebald, C., & Steinfeld, A. (2011) · Energy & Environmental Science · doi:10.1039/c1ee01681d · Cited by 252
Post combustion CO2 capture by carbon fibre monolithic adsorbents
Thiruvenkatachari, R., Su, S., An, H., & Yu, X. X. (2009) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2009.05.003 · Cited by 251
Research works printed but not linked: 6
- 2014, Climate change mitigation: Summary for Policymakers
- 10.1016/j.ijggc.2015.04.018 · DOI · Paper page
- Treybal, R. E. Mass-transfer operations . 3rd ed. McGraw-Hill Book Company, 1980; p 800.
- Berg C., 1946, Trans. AIChE, 665
- 10.1007/s10450-014-9603-2 · DOI · Paper page
- 10.1016/j.cej.2018.10.082 · DOI
Cited by
Items 101–200 of 248
Bao, S., Zheng, X., Xu, Z., Ji, B., Yang, Z., Sun, W., Guo, L., Zhu, Y., Mei, J., Rong, J., et al. (2024) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2024.115171 · Cited by 20
Krishnamurthy, S. (2022) · Chemical Engineering Science · doi:10.1016/j.ces.2022.117585 · Cited by 18
Parameter screening of a VPSA cycle with automated breakthrough control for carbon capture
Gutierrez-Ortega, A., Melis, A., Nomen, R., Sempere, J., Fernández-García, J., Pou, J. O., & Gonzalez‐Olmos, R. (2023) · Fuel · doi:10.1016/j.fuel.2022.127298 · Cited by 17
Gautam, G., Chaudhary, A., & Sahoo, S. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123796 · Cited by 18
Hussein, E. B., & Rasheed, F. A. (2025) · RSC Advances · doi:10.1039/d5ra07804k · Cited by 17
CO2 capture by adsorption: Research progress and technology demonstration
Pini, R., Petit, C., Danaci, D., Haghpanah, R., Luberti, M., Ribeiro, A. M., Subraveti, S. G., & Ward, A. (2026) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2026.104652 · Cited by 16
Krishnamurthy, S., Roelant, R., Blom, R., Arstad, B., Li, Z., Rombouts, M., Middelkoop, V., Borrás, A. B., & Naldoni, L. (2024) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2024.104069 · Cited by 15
Electrothermal Carbon Capture and Utilization─A Review
Patil, S. C., Fahim, S. T. M., Lee, J. H., & Gilliard‐AbdulAziz, K. L. (2024) · ACS Energy Letters · doi:10.1021/acsenergylett.4c02851 · Cited by 18
Nedoma, M., Netušil, M., & Hrdlička, J. (2023) · Fuel · doi:10.1016/j.fuel.2023.129346 · Cited by 15
Mohiuddin, N., Vel, V., Vibhandik, J., Velagala, S. K. R., Singh, S. A., & Sreedhar, I. (2025) · Separation and Purification Technology · doi:10.1016/j.seppur.2025.135900 · Cited by 14
Bharath, Y., & Rajendran, A. (2023) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2023.104016 · Cited by 14
CO2 adsorption by zeolites: State-of-Art, techniques and emerging trends
Dias, E. A. P., da Silva, D. G., Amaral, M. D. C., Pereira, L. D. S., de Melo, D. C., & Vasconcelos, W. L. (2025) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2025.113904 · Cited by 26
Innovative approaches to carbon capture using fluidized bed reactors: A brief review
Duan, Y., Li, L., Lu, D. Y., Zhang, S., Sun, G., Sun, Z., & Duan, L. (2026) · Fuel · doi:10.1016/j.fuel.2026.138295 · Cited by 15
Prabhu, A., Gopalsamy, K., Reddy, K. S. K., Othman, I., BANAT, F. A., Karanikolos, G. N., & Haija, M. A. (2022) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2023.110350 · Cited by 13
Correia, I. D. S., Ilkaeva, M., Castellino, M., Bocchini, S., Novais, R. M., Mafra, L., Gonçalves, N. P. F., & Lourenço, M. A. O. (2024) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2024.113875 · Cited by 13
Scale-up strategies for adsorption-based reactors with efficient direct air capture
Chen, S., Xie, R., Shi, W. S., Wang, R., Zhang, X., Wang, T., Font-Palma, C., & Jiang, L. (2025) · Device · doi:10.1016/j.device.2024.100614 · Cited by 15
Jamei, R., McDonough, J. R., Reay, D. A., & Živković, V. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2022.138405 · Cited by 13
“8 more closely resemble the curve reported by Dhoke et al. [43] when separators were added to improve the plug flow performance of the gas phase, than compared to the curve without separators when the bed behaved as a single well-mixed tank.”
Swapna, S., Ramudu, M. P., Reddy, P. V., Kumar, G. R., Bindu, G. H., Challa, P., & Mallesh, D. (2024) · Journal of the Chinese Chemical Society · doi:10.1002/jccs.202400261 · Cited by 13
Choi, J., Paudel, A., Karki, B., Bradley, K., Quinn, N., & Ciric, A. (2025) · Resources Environment and Sustainability · doi:10.1016/j.resenv.2025.100195 · Cited by 12
Zhou, Z., Ling, H., Zhao, Y., Li, H., Yang, Z., & Hu, X. E. (2025) · Separation and Purification Technology · doi:10.1016/j.seppur.2025.132051 · Cited by 12
σ‐ Hole intermolecular interactions between carbon oxides and dihalogens: Ab‐initio investigations
Rahali, E., Zouaghi, M. O., Sanz, J. F., Raouafi, N., & Arfaoui, Y. (2023) · Journal of Computational Chemistry · doi:10.1002/jcc.27098 · Cited by 12
Zhao, J., Tian, X., Niu, Q., & Zhang, P. (2023) · Separation and Purification Technology · doi:10.1016/j.seppur.2023.125760 · Cited by 12
Ibrahim, S., Hameed, B. H., & AlMomani, F. A. (2024) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2024.114952 · Cited by 14
Li, L., Meng, Y., Li, J., Chen, K., Hu, E., Chang, J., Gao, Y., & Jiang, J. (2025) · Journal of Materials Chemistry A · doi:10.1039/d5ta00973a · Cited by 11
Li, S., Du, Z., Wang, J., Wang, H., Cao, X. E., Chen, R., Pang, Y., Deng, S., Mašek, O., Yuan, X., et al. (2025) · Carbon Research · doi:10.1007/s44246-025-00209-5 · Cited by 12
“This process allows powdered adsorbents to be transformed into structured adsorbents, which can be used in fixed-bed reactors with reduced pressure drop (Dhoke et al. 2021; Wadi et al. 2021).”
Qiao, L., Chen, J., & Fu, D. (2025) · Energy & Fuels · doi:10.1021/acs.energyfuels.5c01410 · Cited by 12
Experimental and simulation study of CO2 breakthrough curves in a fixed-bed adsorption process
Nedoma, M., Staf, M., & Hrdlička, J. (2022) · Acta Polytechnica · doi:10.14311/ap.2022.62.0370 · Cited by 10
Human security and mobility in the context of climate change in Africa
Chigudu, D. (2024) · Watershed Ecology and the Environment · doi:10.1016/j.wsee.2024.10.004 · Cited by 10
Yang, K., Zhang, Y., Zhang, Z., Wang, Q., Ye, G., Xue, Z., Luo, J., & Yang, H. (2025) · Applied Energy · doi:10.1016/j.apenergy.2025.125666 · Cited by 9
CO 2 Capture, Utilization, and Storage using Amino Acids
Sheikh, M. S., Sui, J., Wang, B., & Wang, X. (2025) · Advanced Sustainable Systems · doi:10.1002/adsu.202501422 · Cited by 10
Qiao, L., & Fu, D. (2024) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2024.115218 · Cited by 9
Hierarchical Mesoporous SSZ-13 Chabazite Zeolites for Carbon Dioxide Capture
Hillen, L., & Degirmenci, V. (2021) · Catalysts · doi:10.3390/catal11111355 · Cited by 9
“Therefore, the thermodynamics and kinetics affected the choice of the sorbent and the process, which is highlighted in recent literature [12,13].”
BackgroundDesign and principles of adsorbent-based reactors for modular wastewater treatment
Chaudhary, M., Jain, N., Barman, L., & Bhowmick, G. D. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-85421-4.00018-8 · Cited by 11
Muniz, R. N., Buratto, W. G., Cardoso, R., Barros, C. F. D. O., Nied, A., & González, G. V. (2025) · Water · doi:10.3390/w17131946 · Cited by 8
Ock, D., Kang, Y., Lee, J., Kim, S., Mok, J., Go, W., & Choi, W. (2025) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-024-00378-w · Cited by 7
Tripoonsuk, C., Limahksohn, M., Chalermsinsuwan, B., & Piumsomboon, P. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.167473 · Cited by 6
Recent advancements and assessment of carbon capture technologies for climate crisis mitigation
Zainal, B. S., Fattah, I. M. R., Ong, H. C., Muraza, O., Osman, N., & Mahlia, T. M. I. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.175776 · Cited by 8
Tai, X., Lang, J., Zhang, W., Yu, D., & Tai, X. (2026) · RSC Advances · doi:10.1039/d6ra03652j · Cited by 7
Washcoated zeolite structured adsorbents for CO2 capture and recovery by rotary adsorption
Li, Z., Wang, C., Xiao, J., Xu, J., Sun, N., Yang, X., & Liu, Y. (2025) · Carbon Capture Science & Technology · doi:10.1016/j.ccst.2025.100378 · Cited by 7
Sami, S., Gholizadeh, M., & Deymi‐Dashtebayaz, M. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115376 · Cited by 7
CO2 Hydrate Formation Kinetics Using Aqueous MOF Ink-Soaked Water-Absorbing Materials
Pandey, J. S., & Mahant, B. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.4c03502 · Cited by 6
Kamlekar, P., Jha, M. K., Kundu, K., & Kishore, B. (2025) · Renewable Energy · doi:10.1016/j.renene.2025.124060 · Cited by 7
RETRACTED ARTICLE: A review on different methods of CO2 capture, separation and utilization
Das, D., Agarwal, T., & Biswal, A. K. (2023) · Brazilian Journal of Chemical Engineering · doi:10.1007/s43153-023-00378-z · Cited by 6
RetractedAnsari, A., & Shahhosseini, S. (2024) · Case Studies in Chemical and Environmental Engineering · doi:10.1016/j.cscee.2024.100895 · Cited by 6
Production of chemicals via tandem conversion of bio-oil derived fractions
Naranov, E. R., Sadovnikov, A. A., Арапова, О. В., Guda, A. A., Dement’ev, K. I., Arzumanyan, A. V., Kubrin, G. E., Kholodkov, D. N., Zagrebaev, A. D., Wang, K., et al. (2024) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2024.115050 · Cited by 7
Jose, H., & Rabha, S. S. (2025) · Powder Technology · doi:10.1016/j.powtec.2025.120804 · Cited by 5
Vinayak, R. (2026) · ChemistrySelect · doi:10.1002/slct.73531 · Cited by 5
Enhanced single-loop control of a moving bed temperature swing adsorption CO2 capture process
Skjervold, V. T., & Nord, L. O. (2023) · Computers & Chemical Engineering · doi:10.1016/j.compchemeng.2023.108387 · Cited by 5
El‐Kady, A. H., Amin, M. T., Khan, F. I., & Choudhury, Q. (2024) · Offshore Technology Conference · doi:10.4043/35356-ms · Cited by 5
Bizon, K. (2023) · Chemical and Process Engineering New Frontiers · doi:10.24425/cpe.2023.146726 · Cited by 6
Riahi, A., Heggem, E., Caccia, M., & LaDouceur, R. M. (2024) · Carbon Trends · doi:10.1016/j.cartre.2024.100361 · Cited by 5
Vannak, H., Osaka, Y., Tsujiguchi, T., Fujiwara, K., Kumita, M., Ohnishi, R., Hikima, S., & Kodama, A. (2025) · Separation and Purification Technology · doi:10.1016/j.seppur.2025.134392 · Cited by 4
Experimentation of a novel sequential moving-bed DAC System
Marcil, A., Lacroix, M.-A., Hotte-Bélanger, T., Vézina, G., & Brouillette, M. (2025) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2025.104472 · Cited by 4
Raganati, F., & Ammendola, P. (2026) · Energy & Fuels · doi:10.1021/acs.energyfuels.6c02221 · Cited by 5
Carbon Dioxide Capture Performance of Mesostructured Adsorbent Impregnated with Polyethylenimine
Chen, C., Yu, C., & Chang, Y.-F. (2024) · International Journal of Engineering and Technology Innovation · doi:10.46604/ijeti.2024.13298 · Cited by 4
“Various reactor configurations, including fixed beds, moving beds, and fluidized beds, have been discussed in previous reports [16-17].”
BackgroundJedli, H., Bouzgarrou, S. M., Hassani, R., Sabi, E., & Slimi, K. (2025) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-025-14112-z · Cited by 4
Fundamental of CO 2 Adsorption and Diffusion in Subnanoporous Materials: Application to CALF-20
Gonçalves, A. D. F., Lyra, E. P., Chavan, S. R., Llewellyn, P. L., Franco, L. F. M., & Magnin, Y. (2025) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.5c03130 · Cited by 6
“[34, 35] The company Svante has already demonstrated the efficiency of the CALF-20 by integrating it in its rapid temperature swing adsorption process, shown to capture up to 1 tonne of CO 2 per day from cement plant flue gases.”
Comparative Studies on Thermal-Hydraulic Performance of Adsorption Vessels for CO 2 Storage
Gautam, G., Chaudhary, A., & Sahoo, S. (2023) · Heat Transfer Engineering · doi:10.1080/01457632.2023.2295084 · Cited by 4
Riahi, A., Muretta, J. E., & LaDouceur, R. M. (2025) · Carbon Trends · doi:10.1016/j.cartre.2025.100521 · Cited by 4
Juul, G., Korhonen, A.-K., Neupane, G., Lagus, H., Kajaste, J. T., Järvinen, M., & Vepsäläinen, J. (2025) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2025.126834 · Cited by 4
Mechanical compression-induced shaping of zinc triazolate oxalate CALF-20 for CO2 capture
Lv, S., Yan, X., Zhong, Y., Liu, P., Kang, G., Lu, S., Hu, X., & Hu, M. (2025) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2025.08.013 · Cited by 3
Médina, O. E., Narváez, P., Amell, A. A., López, D., & Santamaría, A. (2025) · Green chemistry and sustainable technology · doi:10.1007/978-3-031-91199-6_9 · Cited by 3
Thermal Management in Solid Sorbent CO 2 Capture through Fluidization: Experimental and CFD Studies
Goel, P., & Rabha, S. S. (2025) · Energy & Fuels · doi:10.1021/acs.energyfuels.5c04483 · Cited by 3
Rafique, M., Hussain, D., Kalwar, B. A., Ahmed, I., Hassan, M., Li, L., Wang, B., Mustafa, A., Lougou, B. G., & Shuai, Y. (2025) · Inorganic Chemistry Communications · doi:10.1016/j.inoche.2025.115136 · Cited by 3
Monteiro, A. F., Gribble, D. A., Jayaraman, A., Alptekin, G., Hughes, R., Kotamreddy, G., Omell, B. P., Matuszewski, M., & Bhattacharyya, D. (2025) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2025.104481 · Cited by 3
Rapid Steam‐Assisted Temperature Swing Adsorption for Direct Air Capture Using a Rotary Adsorber
Wu, J., Chen, Y., Wang, K., Huo, Y., Chen, Y., Pan, Q., & Ge, T. (2026) · Advanced Science · doi:10.1002/advs.202521499 · Cited by 4
“Additionally, it exhibits high adsorbent attrition rates, and the absence of established scale-up methodologies creates uncertainty in practical applications [ 28, 29 ].”
Viciazites: Carbon materials with adjacent nitrogen functionalities for advanced CO2 capture
Kondo, K., Uchizono, A., Pu, L., Takahashi, I., Suzuki, R., Nakamura, S., Kan, K., Kazuma Gotoh, B., Soejima, T., Sato, S., et al. (2026) · Carbon · doi:10.1016/j.carbon.2026.121405 · Cited by 4
Enhancement of CO2 capture in post combustion process using actived carbon modified by amino acids
Houshmand, D., Rashidi, F., Amjad‐Iranagh, S., & Hajilari, M. (2026) · Scientific Reports · doi:10.1038/s41598-026-44400-z · Cited by 4
Brandão, R. J., GOMES, T. L. C., Sivaraman, S., de Sousa, R. C., Selvasembian, R., & Meili, L. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.138475 · Cited by 3
Golmohammadi, M., Taheri, E., Permala, R. R., Allard, S., Khiadani, M., & Razmjou, A. (2026) · Journal of Water Process Engineering · doi:10.1016/j.jwpe.2026.110322 · Cited by 4
Lu, T., Li, H., Jing, H., Qiu, P., Rao, H., & Qi, Y. (2025) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2025.113808 · Cited by 3
Dhoke, C., Cloete, S. W. P., Amini, S., & Zaabout, A. (2021) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.1c00357 · Cited by 3
Self-citationMass transport, kinetic model, and application of CO2 adsorption on zeolite 5A granules
Sangsuradet, S., & Worathanakul, P. (2023) · CLEAN - Soil Air Water · doi:10.1002/clen.202200406 · Cited by 6
von Heynitz, C., Bachmann, F., Hofmann, T. F., & Glas, K. (2024) · ACS Sustainable Resource Management · doi:10.1021/acssusresmgt.4c00089 · Cited by 2
Murillo-Rincón, J., Paglianti, A., Alberini, F., & Montante, G. (2025) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2025.110570 · Cited by 3
Simulated Moving Bed Process for CO 2 Capture from Humid Postcombustion Flue Gases Using MUF-16
Sarswat, A., Guta, Y. A., Zorrilla-Valtierra, M., Cochran, A., Kim, S., Sholl, D. S., & Lively, R. P. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c16139 · Cited by 2
hua, Y., & Kim, K. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.116485 · Cited by 2
Narváez, J., Bastardo-González, E., Ávila, E. E., Palma‐Cando, A., Galarraga, P., Guerrero, V. H., & Ricaurte, M. (2026) · ACS Omega · doi:10.1021/acsomega.5c06923 · Cited by 2
Arathi, P. K., Sudha, D., & Suresh, C. H. (2026) · Physical Chemistry Chemical Physics · doi:10.1039/d5cp04586j · Cited by 2
Vannak, H., Fujiwara, K., Osaka, Y., Tsujiguchi, T., & Kodama, A. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.137190 · Cited by 2
Ahmed, M., Yang, Y., Li, T., Liu, Z., Aamir, A., Wang, S., Gao, C., & Liu, X. (2026) · Powder Technology · doi:10.1016/j.powtec.2026.122386 · Cited by 2
Yergaziyeva, G., Mambetova, M., Makayeva, N., Liu, X., Pei, J., Myltykbayeva, L. K., Қуаныш, І., & Dossumov, K. (2026) · Inorganic Chemistry Communications · doi:10.1016/j.inoche.2026.116910 · Cited by 2
Covalent Organic Frameworks for CO2 Capture: From Design to Application
Nabipour, H., & Rohani, S. (2026) · Nanomaterials · doi:10.3390/nano16120777 · Cited by 2
Rackley, S. (2023) · Elsevier eBooks · doi:10.1016/b978-0-12-819663-2.00012-5 · Cited by 2
Goel, P., & Rabha, S. S. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.4c00435 · Cited by 2
Innovations in Biomass-Derived Materials for Efficient CO₂ Sequestration
Verma, S. K., Singh, D., Sharan, A., Khare, R., Rai, S., Kumar, P., & Singh, V. (2025) · Chemistry Africa · doi:10.1007/s42250-024-01179-8 · Cited by 2
“Even though the particular metals in MOF may increase selectivity, the preparation process for MOF is more laborious and expen - sive, which makes industrialization challenging [ 2].”
Zang, S., & Harada, T. (2025) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.4c10285 · Cited by 2
Adjustable gas adsorption and desorption via a self-shrinking nanoscroll
Wan, J., Cai, K. P., Kang, Y., Luo, Y., & Qin, Q. (2023) · Applied Physics Letters · doi:10.1063/5.0175953 · Cited by 2
Sahu, D., Pervez, S., Tamrakar, A., Karbhal, I., Deb, M. K., Shrivas, K. K., Satnami, M. L., Pervez, Y. F., & Verma, S. K. (2025) · Environmental Functional Materials · doi:10.1016/j.efmat.2025.11.001 · Cited by 1
Khastkhodaei, M. H., Esfandiari, N., Nabipour, M., & Honarvar, B. (2025) · Separation Science and Technology · doi:10.1080/01496395.2025.2602155 · Cited by 1
“12] The foundation of this revolutionary adsorbent lies in the implementation of open-cell polyurethane foam (OPUF) as the host material for confining and immobilizing the highly desirable CO 2 powder adsorbents.”
Asif, A. H., & Sun, H. (2025) · Advanced Nanocomposites · doi:10.1016/j.adna.2025.12.001 · Cited by 1
Development and optimization of twin-tower system for continuous post-combustion CO2 capture
Hongkhamdee, C., Wang, W., Nugroho, R. A. A., Verma, V., Xavier, D., Thamma, U., & Wongcharoen, A. (2026) · Clean Technologies and Environmental Policy · doi:10.1007/s10098-025-03362-y · Cited by 1
“From an energy perspective, the system’s consumption of 0.6 kWh kg −1 CO 2 (~ 2.16 MJ kg −1 ) is competitive with or lower than the ranges reported for conventional PSA (2–4 MJ kg −1 ) and fluidized-bed systems (1.3–2.8 MJ kg −1 ) (Dhoke et al. 2021).”
InfluentialRiahi, A., & LaDouceur, R. M. (2026) · IntechOpen eBooks · doi:10.5772/intechopen.1013522 · Cited by 1
Wu, J., Zhao, R., Liu, W. F., Li, C., Zhao, M., Gao, C., Deng, S., & Zhao, L. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.122624 · Cited by 1
Singh, N., Dahiya, S., Tambi, A., Bassi, A., Parida, V. K., & Varshney, A. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.139092 · Cited by 3
CO2 removal by applying the adsorption process to biochar from waste materials
Costa, M. A. M., Albini, G., de Oliveira, L. F., de Oliveira, E. A., de Souza, A. J. D., Bérgamo, M. D. O., Moreno, L. V., & Dussan, K. J. (2026) · Environmental Science and Pollution Research · doi:10.1007/s11356-026-37975-7 · Cited by 2
Revisiting TSA and TVSA for DAC: Operating Windows, Thermodynamic Bounds, and Exergy Efficiency
Höfer, G., & Pröll, T. (2026) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.6c02452 · Cited by 1
Li, C., Sun, R., Gao, B., Gao, G., Shao, Y., Guo, Y., Zhang, L., Wei, T., Zhang, S., & Hu, X. (2026) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2026.108003 · Cited by 2
Wei, X., Kot-Cheung, S. K., & Sun, J. (2026) · Molecules · doi:10.3390/molecules31173056 · Cited by 1
“Fixed-bed systems provide simple operation and mature engineering experience, yet their application in DAC is limited by pressure drop, internal diffusion resistance, and heat-transfer constraints [96].”
The role of CO2 sorbents materials in SESMR for hydrogen production
da Silva, T. H. S., Chaghouri, M., Cesário, M. R., Tidahy, H. L., Gennequin, C., de Macedo, D. A., & Abi‐Aad, E. (2022) · Elsevier eBooks · doi:10.1016/b978-0-323-85612-6.00006-1 · Cited by 1
Metadata
- Authors
- Dhoke, C., Zaabout, A., Cloete, S., & Amini, S.
- Affiliations
- Norwegian University of Science and Technology (NO)
- SINTEF Industry (NO)
- University of Alabama (US)
- Corresponding author
- Zaabout, Abdelghafour
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2021-03-05
- Volume
- 60
- Issue
- 10
- Pages
- 3779-3798
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W3133859536
- Cited by
- 240
- References
- 115
- Citations by year
- 2026: 53 · 2025: 51 · 2024: 50 · 2023: 46 · 2022: 30 · 2021: 10
- FWCI
- 14.53
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Industrial & Engineering Chemistry Research (publishedVersion, cc-by)
- NORA - Norwegian Open Research Archives (submittedVersion, cc-by)
- Funders
- Norges Forskningsr?d (268507/E20)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Engineering › Computational Mechanics › Granular flow and fluidized beds
- Physical Sciences › Environmental Science › Environmental Engineering › Industrial Gas Emission Control
- Keywords
- CO2 capture, reactor configuration, fixed bed, fluidized bed, movable bed, adsorbent regeneration, pressure swing adsorption, temperature swing adsorption, technology readiness level, retrofitting, CO2 avoidance cost
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.