Review on Reactor Configurations for Adsorption-Based CO 2 Capture
Open accessThe DOI matches its Crossref record; 112 of the 115 references it cites were found in a registry or an index.
Abstract
Adsorption-based CO2 capture has enjoyed considerable research attention in recent years. Most of the research efforts focused on sorbent development to reduce the energy penalty. However, the use of suitable gas–solid contacting systems is key for extracting the full potential from the sorbent to minimize operating and capital costs and accelerate the commercial deployment of the technology. This paper reviews several reactor configurations that were proposed for adsorption-based CO2 capture. The fundamental behavior of adsorption in different gas–solid contactors (fixed, fluidized, moving, or rotating beds) and regeneration under different modes (pressure, temperature, or combined swings) is discussed, highlighting the strengths and limitations of different combinations of gas–solid contactor and regeneration mode. In addition, the estimated energy duties in published studies and current technology readiness level of the different reactor configurations are reported. Other aspects, such as the reactor footprint, the operation strategy, suitability to retrofits, and the ability to operate under flexible loads are also discussed. In terms of future work, the key research need is a standardized techno-economic benchmarking study to calculate CO2 avoidance costs for different adsorption technologies under standardized assumptions. Qualitatively, each technology presents several strengths and weaknesses that make it impossible to identify a clear optimal solution. Such a standardized quantitative comparison is therefore needed to focus on future technology development efforts.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“It has been shown, in fact, that alternative microstructures can offer much lower pressure drops [49].”
From Topology optimisation of adsorption beds for cost-effective direct air capture (2026) · cites this paper as [49]
Citations
Cites
Carbon capture and storage (CCS): the way forward
Bui, M., Adjiman, C. S., Bardow, A., Anthony, E. J., Boston, A., Brown, S., Fennell, P. S., Fuss, S., Galindo, A., Hackett, L. A., et al. (2018) · Energy & Environmental Science · doi:10.1039/c7ee02342a · Cited by 4,374
Principles of adsorption and adsorption processes
Kast, W. (1985) · Chemical Engineering and Processing: Process Intensification · doi:10.1016/0255-2701(85)80013-1 · Cited by 2,430
Post-Combustion CO 2 Capture Using Solid Sorbents: A Review
Samanta, A., Zhao, A., Shimizu, G. K. H., Sarkar, P., & Gupta, R. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie200686q · Cited by 1,889
CO2 capture by solid adsorbents and their applications: current status and new trends
Wang, Q., Luo, J., Zhong, Z., & Borgna, A. (2011) · Energy Environ. Sci. · doi:10.1039/c0ee00064g · Cited by 1,611
Abanades, J. C., Arias, B., Lyngfelt, A., Mattisson, T., Wiley, D. E., Li, H., Ho, M. T., Mangano, E., & Brandani, S. (2015) · International Journal of Greenhouse Gas Control · doi:10.1016/j.ijggc.2015.04.018 · Cited by 441
Alkali and alkaline-earth cation exchanged chabazite zeolites for adsorption based CO2 capture
Zhang, J., Singh, R., & Webley, P. A. (2008) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2007.08.022 · Cited by 313
Structured adsorbents in gas separation processes
Rezaei, F., & Webley, P. (2010) · Separation and Purification Technology · doi:10.1016/j.seppur.2009.10.004 · Cited by 294
CO2 capture from dry flue gas by vacuum swing adsorption: A pilot plant study
Krishnamurthy, S., Rao, V. R., Guntuka, S., Sharratt, P., Haghpanah, R., Rajendran, A., Amanullah, M., Karimi, I. A., & Farooq, S. (2014) · AIChE Journal · doi:10.1002/aic.14435 · Cited by 282
Wurzbacher, J. A., Gebald, C., & Steinfeld, A. (2011) · Energy & Environmental Science · doi:10.1039/c1ee01681d · Cited by 252
Post combustion CO2 capture by carbon fibre monolithic adsorbents
Thiruvenkatachari, R., Su, S., An, H., & Yu, X. X. (2009) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2009.05.003 · Cited by 251
Research works printed but not linked: 6
- 2014, Climate change mitigation: Summary for Policymakers
- 10.1016/j.ijggc.2015.04.018 · DOI · Paper page
- Treybal, R. E. Mass-transfer operations . 3rd ed. McGraw-Hill Book Company, 1980; p 800.
- Berg C., 1946, Trans. AIChE, 665
- 10.1007/s10450-014-9603-2 · DOI · Paper page
- 10.1016/j.cej.2018.10.082 · DOI
Cited by
Dziejarski, B., Krzyżyńska, R., & Andersson, K. (2023) · Fuel · doi:10.1016/j.fuel.2023.127776 · Cited by 628
Adsorption of Carbon Dioxide for post-combustion capture: a review
Raganati, F., Miccio, F., & Ammendola, P. (2021) · Energy & Fuels · doi:10.1021/acs.energyfuels.1c01618 · Cited by 661
Recent advances in direct air capture by adsorption
Zhu, X., Xie, W., Wu, J., Miao, Y., Xiang, C., Chen, C., Ge, B., Gan, Z., Yang, F., Zhang, M., et al. (2022) · Chemical Society Reviews · doi:10.1039/d1cs00970b · Cited by 456
CO2 Post-combustion Capture: A Critical Review of Current Technologies and Future Directions
Raganati, F., & Ammendola, P. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.4c02513 · Cited by 296
Gunawardene, O. H. P., Gunathilake, C. A., Vikrant, K., & Amaraweera, S. M. (2022) · Atmosphere · doi:10.3390/atmos13030397 · Cited by 249
Karimi, M., Shirzad, M., Silva, J. A. C., & Rodrigues, A. E. (2022) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2022.101890 · Cited by 237
Design of highly microporous activated carbons based on walnut shell biomass for H2 and CO2 storage
Serafin, J., Dziejarski, B., Cruz Junior, O. F., & Sreńscek-Nazzal, J. (2023) · Carbon · doi:10.1016/j.carbon.2022.09.013 · Cited by 210
“Solid sorbents, particularly activated carbons (ACs), have received a lot of attention in recent years as potential CCS candidates [4,5].”
BackgroundCO2 capture by adsorption on biomass-derived activated char: A review.
Goel, C., Mohan, S., & Dinesha, P. (2021) · Science of the Total Environment · doi:10.1016/j.scitotenv.2021.149296 · Cited by 206
Covalent organic frameworks for CO2 capture: from laboratory curiosity to industry implementation
Li, H., Dilipkumar, A., Abubakar, S., & Zhao, D. (2023) · Chemical Society Reviews · doi:10.1039/d2cs00465h · Cited by 191
Activated carbons—preparation, characterization and their application in CO2 capture: A review
Serafin, J., & Dziejarski, B. (2023) · Environmental Science and Pollution Research · doi:10.1007/s11356-023-28023-9 · Cited by 179
Carbon Capture Technologies: A Review on Technology Readiness Level
Hekmatmehr, H., Esmaeili, A., Pourmahdi, M., Atashrouz, S., Abedi, A., Ali Abuswer, M., Nedeljkovic, D., Latifi, M., Farag, S., & Mohaddespour, A. (2024) · Fuel · doi:10.1016/j.fuel.2024.130898 · Cited by 189
Wang, S., Lee, Y.-R., Won, Y., Kim, H., Jeong, S.-E., Wook Hwang, B., Ra Cho, A., Kim, J.-Y., Cheol Park, Y., Nam, H., et al. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2022.135378 · Cited by 171
A review on biomass-derived CO2 adsorption capture: Adsorbent, adsorber, adsorption, and advice
Li, S., Yuan, X., Deng, S., Zhao, L., & Lee, K. B. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111708 · Cited by 152
Bouaboula, H., Chaouki, J., Belmabkhout, Y., & Zaabout, A. (2024) · Chemical Engineering Journal · doi:10.1016/j.cej.2024.149411 · Cited by 159
Self-citationKong, M. G., Song, L., Liao, H., Zhang, S., Wang, Y., Deng, X., & Feng, W. (2024) · Fuel · doi:10.1016/j.fuel.2024.132103 · Cited by 155
Management of surgical mask waste to activated carbons for CO2 capture
Serafin, J., Sreńscek-Nazzal, J., Kamińska, A., Paszkiewicz, O., & Michalkiewicz, B. (2022) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2022.101970 · Cited by 124
Akinola, T. E., Prado, P. L. B., & Wang, M. (2022) · Applied Energy · doi:10.1016/j.apenergy.2022.119156 · Cited by 119
An overview of porous silica immobilized amines for direct air CO 2 capture
Cherevotan, A., Raj, J., & Peter, S. C. (2021) · Journal of Materials Chemistry A · doi:10.1039/d1ta05961k · Cited by 111
Gopalan, J., Buthiyappan, A., & Raman, A. A. A. (2022) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2022.06.026 · Cited by 103
Study on CO2 adsorption capacity and kinetic mechanism of CO2 adsorbent prepared from fly ash
Guo, B., Zhang, J., Wang, Y., Qiao, X., Xiang, J. H., & Jin, Y. J. (2022) · Energy · doi:10.1016/j.energy.2022.125764 · Cited by 94
Shaping techniques of adsorbents and their applications in gas separation: a review
Wu, J., Zhu, X., Yang, F., Wang, R. Z., & Ge, T. (2022) · Journal of Materials Chemistry A · doi:10.1039/d2ta04352a · Cited by 91
Insights into the adsorption of CO2, SO2 and NOx in flue gas by carbon materials: A critical review
Hou, Y., Chen, Y., He, X., Wang, F., Cai, Q., & Shen, B. (2024) · Chemical Engineering Journal · doi:10.1016/j.cej.2024.151424 · Cited by 85
Adsorption of CO2 onto zeolite ZSM-5: Kinetic, equilibrium and thermodynamic studies
Jedli, H., Almoneef, M. M., Mbarek, M., Jbara, A., & Slimi, K. (2022) · Fuel · doi:10.1016/j.fuel.2022.124097 · Cited by 83
A fast methodology to rank adsorbents for CO2 capture with temperature swing adsorption
Gutierrez-Ortega, A., Nomen, R., Sempere, J., Parra, J. B., Montes-Morán, M. Á., & Gonzalez‐Olmos, R. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2022.134703 · Cited by 81
Amer, N. M., Lahijani, P., Mohammadi, M., & Mohamed, A. R. (2022) · Biomass Conversion and Biorefinery · doi:10.1007/s13399-022-02905-3 · Cited by 78
“…[73], (2) TSA: temperature-swing adsorption [74], (3) PTSA: pressure and temperature-swing adsorption [69], (4) VPSA: vacuum pressure-swing adsorption [75], (5) ESA: electric-swing adsorption [76], (6) RPSA: rapid pressure-swing adsorption, and (7) URPSA: ultra-rapid pressure-swing adsorption [72].”
Abdelhamid, H. N. (2022) · Applied Organometallic Chemistry · doi:10.1002/aoc.6753 · Cited by 75
Kim, C., Ha, Y., & Choi, M. (2023) · Accounts of Chemical Research · doi:10.1021/acs.accounts.3c00326 · Cited by 72
Recent Advances in Quantum Dots for Photocatalytic CO2 Reduction: A Mini-Review
Park, Y. H., Murali, G., Modigunta, J. K. R., In, I., & In, S. (2021) · Frontiers in Chemistry · doi:10.3389/fchem.2021.734108 · Cited by 65
Sivaranjani, R., Veerathai, S., Jenifer, K. J., Sowmiya, K., Rupesh, K. J., Sudalai, S., & Arumugam, A. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.03.161 · Cited by 67
Activated carbon derived from Biomass combustion bottom ash as solid sorbent for CO2 adsorption
Gorbounov, M., Petrovic, B., Ozmen, S., Clough, P. T., & Soltani, S. M. (2023) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2023.04.057 · Cited by 60
“…interactions, i.e. a suitable combination of the adsorbent and a particular regeneration mode (electric/pressure(and/or vacuum)/temperature swing (Dhoke, 2021) (Raganati et al., 2021) or some combination thereof), an appropriate gas-solid contactor configuration (fixed (Ammendola,…”
BackgroundPatel, H., Mohanty, A. K., & Misra, M. (2024) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2024.114484 · Cited by 62
Sun, J., Li, H., Liu, Q., Zhong, W., & Dong, W. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.165890 · Cited by 70
Kinetics and mechanism analysis of CO2 adsorption on LiX@ZIF-8 with core shell structure
Yang, F., Zhu, X., Wu, J., Wang, R. Z., & Ge, T. (2021) · Powder Technology · doi:10.1016/j.powtec.2021.117090 · Cited by 56
Chakrabortty, S., Kumar, R., Nayak, J., Jeon, B., Dargar, S. K., Tripathy, S. K., Pal, P., Ha, G.-S., Kim, K. H., & Jasiński, M. (2023) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.113417 · Cited by 57
Ramar, V., & Balraj, A. (2022) · Energy & Fuels · doi:10.1021/acs.energyfuels.2c02585 · Cited by 53
AlMomani, F. A., Abdelbar, A., & Ghanimeh, S. A. (2023) · Sustainability · doi:10.3390/su151310438 · Cited by 56
“The first one is chemical adsorption (chemisorption), where the exchange of molecules between the sorbent and adsorbent takes place under chemical reactions, resulting in covalent bonds [50].”
BackgroundInfluentialAn introductory review on advanced multifunctional materials
Abdelhamid, H. N. (2023) · Heliyon · doi:10.1016/j.heliyon.2023.e18060 · Cited by 55
Obi, D., Onyekuru, S. O., & Orga, A. (2024) · International Journal of Sustainable Energy · doi:10.1080/14786451.2024.2317137 · Cited by 53
“…terms of process configurations, we have a single stage (Yang et al. 2013) that decreases energy consumption from 114.53 to 28.23 kJ/mol when the initial concentration of CO 2 rises from 15% to 75%; two stages (Dhoke et al. 2021; Liu et al. 2022; Wang et al. 2013) that give high CO 2 purity (> 95”
InfluentialMagnin, Y., Dirand, E., Maurin, G., & Llewellyn, P. L. (2023) · ACS Applied Nano Materials · doi:10.1021/acsanm.3c03752 · Cited by 52
Advancing carbon capture technologies in CCS: A comprehensive review of pre-combustion processes
Vaziri, P., Rasaei, M. R., Seyfoori, S., Zamani, S., Mahmoodi, M., & Sedaee, B. (2024) · Gas Science and Engineering · doi:10.1016/j.jgsce.2024.205481 · Cited by 55
Neisan, R. S., Saady, N. M. C., Bazán, C., Zendehboudi, S., Al‐Nayili, A., Abbassi, B., & Chatterjee, P. (2023) · Clean Technologies · doi:10.3390/cleantechnol5010019 · Cited by 53
Direct air capture of CO2 in designed metal-organic frameworks at lab and pilot scale
Zhang, X., Zhao, H., Yang, Q., Yao, M., Wu, Y., & Gu, Y. (2023) · Carbon Capture Science & Technology · doi:10.1016/j.ccst.2023.100145 · Cited by 75
A Systematic Review of Amino Acid-Based Adsorbents for CO2 Capture
Hatta, N. S. M., Aroua, M. K., Hussin, F., & Gew, L. T. (2022) · Energies · doi:10.3390/en15103753 · Cited by 47
Advancements and challenges in electric heating for enhanced temperature swing adsorption processes
Verougstraete, B., Gholami, M., Gomez-Rueda, Y., Pérez‐Botella, E., Schoukens, M., Assche, T. R. C. V., & Denayer, J. F. M. (2024) · Separation and Purification Technology · doi:10.1016/j.seppur.2024.128522 · Cited by 52
Temperature vacuum swing, a combined adsorption cycle for carbon capture
Gholami, M., Assche, T. R. C. V., & Denayer, J. F. M. (2022) · Current Opinion in Chemical Engineering · doi:10.1016/j.coche.2022.100891 · Cited by 51
Tailoring zeolites for enhanced post-combustion CO2 capture: A critical review
Whaieb, A. H., Jasim, F. T., Abdulrahman, A. A., Khuder, I. M., Gheni, S. A., Fattah, I. M. R., & Karakullukçu, N. T. (2025) · Current Research in Green and Sustainable Chemistry · doi:10.1016/j.crgsc.2025.100451 · Cited by 48
Hoang, T., Bandh, S. A., Malla, F. A., Qayoom, I., Bashir, S., Bashir, S., & Halog, A. (2023) · Recycling · doi:10.3390/recycling8040053 · Cited by 44
Adsorbent shaping as enabler for intensified pressure swing adsorption (PSA): A critical review
Chisăliță, D.-A., Boon, J., & Lücking, L. (2024) · Separation and Purification Technology · doi:10.1016/j.seppur.2024.128466 · Cited by 44
Progress of MOFs/solid material composite adsorbent for efficient CO2 adsorption and separation
Wang, J., Jin, L., Wen, S., Ma, C., Ning, P., & Zhang, Y. L. (2025) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2025.217334 · Cited by 42
Porous Carbon for CO2 Capture Technology: Unveiling Fundamentals and Innovations
Bari, G. A. K. M. R., & Jeong, J.-H. (2023) · Surfaces · doi:10.3390/surfaces6030023 · Cited by 43
Behavior, mechanisms, and applications of low-concentration CO 2 in energy media
Shen, M., Guo, W., Tong, L., Wang, L., Chu, P. K.-H., Kawi, S., & Ding, Y. (2025) · Chemical Society Reviews · doi:10.1039/d4cs00574k · Cited by 49
Review on Carbon Capture in ICE Driven Transport
García‐Mariaca, A., & Llera‐Sastresa, E. (2021) · Energies · doi:10.3390/en14216865 · Cited by 40
Helmi, M., Moazami, F., Ghaemi, A., & Hemmati, A. (2023) · Fuel · doi:10.1016/j.fuel.2022.127300 · Cited by 38
Zhang, Z. X., Xu, H., Hua, W., & Zhao, C. (2022) · Energy Conversion and Management · doi:10.1016/j.enconman.2022.115794 · Cited by 38
Ligero, A., Calero, M., Martín-Lara, M. Á., Blázquez, G., Solís, R. R., & Pérez, A. (2023) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2023.102517 · Cited by 38
An, X., Zhao, K., Pang, W., Zhang, W., Wang, L., Guo, T., & Fu, D. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.133877 · Cited by 36
Adsorption-based post-combustion carbon capture assisted by synergetic heating and cooling
Liu, W., Ji, Y., Huang, Y., Zhang, X., Wang, T., Fang, M., & Jiang, L. (2023) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.114141 · Cited by 36
Emission control and carbon capture from diesel generators and engines: A decade-long perspective
Babamohammadi, S., Birss, A. R., Pouran, H. M., Pandhal, J., & Borhani, T. N. G. (2025) · Carbon Capture Science & Technology · doi:10.1016/j.ccst.2025.100379 · Cited by 37
Nabil, S. K., Roy, S., Algozeeb, W. A., Al‐Attas, T. A., Bari, M. A. A., Zeraati, A. S., Karthick, K., Demingos, P. G., Rao, A., Tran, T., et al. (2023) · Advanced Materials · doi:10.1002/adma.202300389 · Cited by 38
Helmi, M., Farahani, Z. K., Hemmati, A., & Ghaemi, A. (2024) · Scientific Reports · doi:10.1038/s41598-024-56070-w · Cited by 32
“The regeneration process is performed by three methods such as changing both of them resulting in a hybrid regeneration (VTSA/PTSA), changing the temperature (temperature swing; TSA), and changing the pressure (vacuum/pressure swing; VSA/ PSA) 70,71 .”
MethodKarimi, M., Siqueira, R. M., Rodrigues, A. E., Nouar, F., Silva, J. A. C., Serre, C., & Ferreira, A. F. P. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.4c00611 · Cited by 32
Liu, X., Li, Q., Zhang, Y., Zhong, F., Ding, X., & Yu, Z. (2024) · Fuel · doi:10.1016/j.fuel.2024.131239 · Cited by 31
Shao, Q., Gan, Z., Ge, B., Liu, X., Chen, C., O'Hare, D. M., & Zhu, X. (2024) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2024.05.015 · Cited by 31
Influence of regeneration conditions on cyclic CO2 adsorption on NaA zeolite at high pressures
de Oliveira, L. H., Pereira, M. V. A., Meneguin, J. G., de Barros, M. A. S. D., do Nascimento, J. F., & Arroyo, P. A. (2022) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2022.102296 · Cited by 33
Buratto, W. G., Muniz, R. N., Nied, A., Barros, C. F. D. O., Cardoso, R., & González, G. V. (2024) · Sensors · doi:10.3390/s24030967 · Cited by 35
“Verification of the emission reduction potential of polluting gases is performed by parameterizing the applied catalyst/sludge moisture, pressure, initial and average temperature, along with residence time [87].”
BackgroundZentou, H., Aliyu, M., Abdalla, M. A., Abdelaziz, O. Y., Hoque, B., Alloush, A. M., Tayeb, I. M., Patchigolla, K., & Abdelnaby, M. M. (2024) · The Chemical Record · doi:10.1002/tcr.202400188 · Cited by 49
Junior, O. F. C., Gómez, I. C., Rodríguez-Reinoso, F., Silvestre‐Albero, J., Rambo, C. R., & Escandell, M. M. (2023) · Chemical Engineering Science · doi:10.1016/j.ces.2023.118671 · Cited by 28
Mirparizi, M., Shakeriaski, F., Salehi, F., & Zhang, C. (2023) · Sustainable Energy Technologies and Assessments · doi:10.1016/j.seta.2023.103365 · Cited by 28
Skjervold, V. T., & Nord, L. O. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.122907 · Cited by 27
Carbon dioxide sequestration with carbonic anhydrase nanobiocatalysts: a review
Sillu, D., & Achal, V. (2024) · Environmental Chemistry Letters · doi:10.1007/s10311-024-01755-x · Cited by 26
“It is worth mentioning that other static configurations, such as scrubbers and bubble columns, have received significantly less attention compared to packed columns (Dhoke et al. 2021).”
Sustainability of hydrogen manufacturing: a review
Vitta, S. (2024) · RSC Sustainability · doi:10.1039/d4su00420e · Cited by 28
Carbon dioxide capture and utilization in post-combustion: a review
Nouri, E., Raouf, F., Alyani, S. J., Kardan, A., & Moghaddam, A. M. (2025) · Environmental Science and Pollution Research · doi:10.1007/s11356-025-36546-6 · Cited by 27
Zhang, Z. X., & Xu, H. (2023) · Energy · doi:10.1016/j.energy.2023.127550 · Cited by 27
A Review on the State-of-the-Art and Commercial Status of Carbon Capture Technologies
Islam, M. H., & Patlolla, S. R. (2025) · Energies · doi:10.3390/en18153937 · Cited by 27
Teixeira, P., Correia, P., & Pinheiro, C. I. C. (2024) · Chemical Engineering Science · doi:10.1016/j.ces.2024.119856 · Cited by 25
Comparative analysis of the carbon nanotubes and emerging MXene for CO2 capture and storage
Solangi, N. H., Karri, R. R., Mubarak, N. M., & Mazari, S. A. (2024) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2024.03.050 · Cited by 27
Liu, W., Huang, Y., Zhang, X., Wang, T., Fang, M., & Jiang, L. (2024) · Energy Conversion and Management · doi:10.1016/j.enconman.2024.118919 · Cited by 28
Greener carbon capture using microwave heating for the development of cellulose-based adsorbents
Biti, S., McCue, A. J., Dionisi, D., Graça, I., & Martín, C. F. (2023) · Fuel · doi:10.1016/j.fuel.2023.130246 · Cited by 23
“This includes not only testing with larger quantities of AC at larger experimental scales (thermal swing adsorption system), but also establishing optimal adsorption parameters and an optimal bed configuration for TSA regeneration (fixed, fluidised, rotary beds) [44].”
BackgroundBiti, S., McCue, A. J., Dionisi, D., Graça, I., & Martín, C. F. (2023) · International journal of greenhouse gas control · doi:10.1016/j.ijggc.2023.103876 · Cited by 24
Desorption performance of commercial zeolites for temperature-swing CO2 capture
Chen, C., Yu, J., Song, G., & Che, K. (2023) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2023.110253 · Cited by 22
Li, W., Fu, D., & Pan, J. H. (2023) · Energy & Fuels · doi:10.1021/acs.energyfuels.3c02384 · Cited by 22
Amino-modified Mg-MOF-74: Synthesis, characterization and CO2 adsorption performance
Lin, X., Zeng, W., Liu, M., Zhong, Q., Su, T., Gong, L., & Liu, Y. (2022) · Environmental Engineering Research · doi:10.4491/eer.2021.569 · Cited by 21
Sinehbaghizadeh, S., Saptoro, A., Naeiji, P., Tiong, A. N. T., & Mohammadi, A. H. (2022) · Chemical Engineering Science · doi:10.1016/j.ces.2022.118194 · Cited by 21
Shen, M., Hu, Z., Kong, F., Tong, L., Yin, S., Liu, C., Zhang, P., Wang, L., & Ding, Y. (2023) · Reviews in Environmental Science and Bio/Technology · doi:10.1007/s11157-023-09662-3 · Cited by 21
Kim, T., Kim, K., Lee, G., Seo, M., & Hwang, J. (2024) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-024-00053-0 · Cited by 23
A direct air capture rotary adsorber for CO2 enrichment in greenhouses
Wu, J., Wang, K., Zhao, J., Chen, Y., Gan, Z., Zhu, X., Wang, R. Z., Wang, C., Wang, C.-H., Tong, Y. W., et al. (2024) · Device · doi:10.1016/j.device.2024.100510 · Cited by 24
Strobel, M., Erguvan, M., & Amini, S. (2025) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2025.117395 · Cited by 20
Self-citationAssessment of industrial waste for adsorption and capture of CO2: Dynamic and static capture system
Ramos, P. B., Ponce, M. F., Jerez, F., Barreto, G. P., & Bavio, M. A. (2022) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2022.107521 · Cited by 22
Leenders, S. H. A. M., Pankratova, G., Wijenberg, J., Romanuka, J., Gharavi, F., Tsou, J., Infantino, M., van Haandel, L., van Paasen, S. V. B., & Just, P. (2023) · ChemSusChem · doi:10.1002/cssc.202300930 · Cited by 20
Electrospun graphene carbon nanofibers for CO2 capture and storage: A review
Othman, F. E. C., Yusof, N. B., Ismail, A. F., Ilyas, R. A., & Low, H. Y. (2024) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2024.112014 · Cited by 22
Recent advances in CO2 adsorption using aerogel materials: A review
Bahadi, S. A., Hassan, A. H., & Onaizi, S. A. (2024) · Next Materials · doi:10.1016/j.nxmate.2024.100388 · Cited by 29
Halim, A., Mohee, F. M., Liang, R. L. F., & Freire-Gormaly, M. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.172747 · Cited by 20
Massoumılari, Ş., Doğancı, M., & Velioğlu, S. (2022) · AIChE Journal · doi:10.1002/aic.17837 · Cited by 19
Lei, T., Liang, Y., Zhu, Y., Ye, K., Wang, J., & Liang, Y. (2025) · Energy · doi:10.1016/j.energy.2025.134491 · Cited by 18
Facilely Grafting Small Amine Molecules into Co-Exchanged Zeolite for Enhancing CO2 Adsorption
Yang, L., Lin, Y., Zhao, Y., Li, J., Tian, Z., Wu, Y., Hu, H., Wang, H., & Chen, L. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.3c04422 · Cited by 17
Yancy-Caballero, D. M., Hughes, R., Zamarripa, M. A., Omell, B. P., Matuszewski, M., & Bhattacharyya, D. (2022) · SSRN Electronic Journal · doi:10.2139/ssrn.4271570 · Cited by 19
Prado, D. S., Vilarrasa‐García, E., Sampronha, E., Beleli, Y. S., Moreira, F. S., de Paiva, J. L., Roux, G. A. C. L., Bastos-Neto, M., Azevedo, D. C. S., Silva, E. C. N., et al. (2023) · Adsorption · doi:10.1007/s10450-023-00422-x · Cited by 17
“1 a Multistage fluidized bed and b Gas phase CO 2 concentration variation across the reactor length [39] bed desorption tower, where high temperatures drive the CO 2 into a concentrated CO 2 gaseous stream suitable for storage or further processing as chemicals.”
Asgharizadeh, K., Tahmasebpoor, M., Azimi, B., & Imani, M. (2023) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2023.12.019 · Cited by 18
2D Zeolite-Based Thin Film Nanocomposite Membranes for Efficient CO2 Separation
Feng, C., Ma, Y., Wei, J., Deng, M., Qin, Z., Liu, J., Tang, B. H. J., Ma, X., Liu, J., Jiang, W., et al. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.4c01265 · Cited by 17
Mousavi, S., Damizia, M., Hamidi, R., Filippis, P. D., & de Caprariis, B. (2024) · Energy Conversion and Management · doi:10.1016/j.enconman.2024.118982 · Cited by 17
Metadata
- Authors
- Dhoke, C., Zaabout, A., Cloete, S., & Amini, S.
- Affiliations
- Norwegian University of Science and Technology (NO)
- SINTEF Industry (NO)
- University of Alabama (US)
- Corresponding author
- Zaabout, Abdelghafour
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2021-03-05
- Volume
- 60
- Issue
- 10
- Pages
- 3779-3798
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W3133859536
- Cited by
- 240
- References
- 115
- Citations by year
- 2026: 53 · 2025: 51 · 2024: 50 · 2023: 46 · 2022: 30 · 2021: 10
- FWCI
- 14.53
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Industrial & Engineering Chemistry Research (publishedVersion, cc-by)
- NORA - Norwegian Open Research Archives (submittedVersion, cc-by)
- Funders
- Norges Forskningsr?d (268507/E20)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Engineering › Computational Mechanics › Granular flow and fluidized beds
- Physical Sciences › Environmental Science › Environmental Engineering › Industrial Gas Emission Control
- Keywords
- CO2 capture, reactor configuration, fixed bed, fluidized bed, movable bed, adsorbent regeneration, pressure swing adsorption, temperature swing adsorption, technology readiness level, retrofitting, CO2 avoidance cost
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.