The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
Anisotropic Lattice Strain and Mechanical Degradation of High- and Low-Nickel NCM Cathode Materials for Li-Ion Batteries
Abstract
In the near future, the targets for lithium-ion batteries concerning specific energy and cost can advantageously be met by introducing layered LiNi x Co y Mn z O 2 (NCM) cathode materials with a high Ni content ( x ≥ 0.6). Increasing the Ni content allows for the utilization of more lithium at a given cell voltage, thereby improving the specific capacity but at the expense of cycle life. Here, the capacity-fading mechanisms of both typical low-Ni NCM ( x = 0.33, NCM111) and high-Ni NCM ( x = 0.8, NCM811) cathodes are investigated and compared from crystallographic and microstructural viewpoints. In situ X-ray diffraction reveals that the unit cells undergo different volumetric changes of around 1.2 and 5.1% for NCM111 and NCM811, respectively, when cycled between 3.0 and 4.3 V vs Li/Li + . Volume changes for NCM811 are largest for x (Li) < 0.5 because of the severe decrease in interlayer lattice parameter c from 14.467(1) to 14.030(1) Å. In agreement, in situ light microscopy reveals that delithiation leads to different volume contractions of the secondary particles of (3.3 ± 2.4) and (7.8 ± 1.5)% for NCM111 and NCM811, respectively. And postmortem cross-sectional scanning electron microscopy analysis indicates more significant microcracking in the case of NCM811. Overall, the results establish that the accelerated aging of NCM811 is related to the disintegration of secondary particles caused by intergranular fracture, which is driven by mechanical stress at the interfaces between the primary crystallites.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Shannon, R. D. (1976) · Acta Crystallographica Section A · doi:10.1107/s0567739476001551 · Cited by 66,145
Li-ion battery materials: present and future
Nitta, N., Wu, F., Lee, J. T., & Yushin, G. (2015) · Materials Today · doi:10.1016/j.mattod.2014.10.040 · Cited by 7,389
Noh, H.-J., Youn, S., Yoon, C. S., & Sun, Y.-K. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.01.063 · Cited by 2,302
Applications of digital-image-correlation techniques to experimental mechanics
Chu, T. C., Ranson, W. F., & Sutton, M. A. (1985) · Experimental Mechanics · doi:10.1007/bf02325092 · Cited by 2,236
High-energy cathode material for long-life and safe lithium batteries
Sun, Y.-K., Myung, S.-T., Park, B.-C., Prakash, J., Belharouak, I., & Amine, K. (2009) · Nature Materials · doi:10.1038/nmat2418 · Cited by 1,519
On the use of vinylene carbonate (VC) as an additive to electrolyte solutions for Li-ion batteries
Aurbach, D., Gamolsky, K., Markovsky, B., Gofer, Y., Schmidt, M., & Heider, U. (2002) · Electrochimica Acta · doi:10.1016/s0013-4686(01)00858-1 · Cited by 992
The fast azimuthal integration Python library:pyFAI
Ashiotis, G., Deschildre, A., Nawaz, Z., Wright, J. P., Karkoulis, D., Picca, F. E., & Kieffer, J. (2015) · Journal of Applied Crystallography · doi:10.1107/s1600576715004306 · Cited by 927
First-principles investigation of phase stability inLixCoO2
Van der Ven, A., Aydinol, M. K., Ceder, G., Kresse, G., & Hafner, J. (1998) · Physical Review B · doi:10.1103/physrevb.58.2975 · Cited by 748
In situ x-ray diffraction and electrochemical studies of Li1−xNiO2
LI, W., Reimers, J. N., & Dahn, J. R. (1993) · Solid State Ionics · doi:10.1016/0167-2738(93)90317-v · Cited by 745
Study of the Failure Mechanisms of LiNi0.8Mn0.1Co0.1O2Cathode Material for Lithium Ion Batteries
Li, J., Downie, L. E., Ma, L., Qiu, W., & Dahn, J. R. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.1011507jes · Cited by 516
Kinetics Tuning of Li-Ion Diffusion in Layered Li(NixMnyCoz)O2
Wei, Y., Zheng, J., Cui, S., Song, X., Su, Y., Deng, W., Wu, Z., Wang, X., Wang, W., Rao, M., et al. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b04040 · Cited by 395
Factors Which Limit the Cycle Life of Rechargeable Lithium (Metal) Batteries
Aurbach, D., Zinigrad, E., Teller, H., & Dan, P. (2000) · Journal of The Electrochemical Society · doi:10.1149/1.1393349 · Cited by 340
Yin, S.-C., Rho, Y.-H., Swainson, I., & Nazar, L. F. (2006) · Chemistry of Materials · doi:10.1021/cm0511769 · Cited by 280
Safety characteristics of Li(Ni0.8Co0.15Al0.05)O2 and Li(Ni1/3Co1/3Mn1/3)O2
Belharouak, I., Lu, W., Vissers, D., & Amine, K. (2006) · Electrochemistry Communications · doi:10.1016/j.elecom.2005.12.007 · Cited by 268
Aurbach, D., Zaban, A., Gofer, Y., Ely, Y. E., Weissman, I., Chusid, O., & Abramson, O. (1995) · Journal of Power Sources · doi:10.1016/0378-7753(94)02044-4 · Cited by 262
Tsai, Y. W., Hwang, B. J., Ceder, G., Sheu, H. S., Liu, D. G., & Lee, J. F. (2005) · Chemistry of Materials · doi:10.1021/cm048027v · Cited by 242
Gent, W. E., Li, Y., Ahn, S., Lim, J., Liu, Y., Wise, A. M., Gopal, C. B., Mueller, D. N., Davis, R., Weker, J. N., et al. (2016) · Advanced Materials · doi:10.1002/adma.201601273 · Cited by 176
Ghanty, C., Markovsky, B., Erickson, E. M., Talianker, M., Haik, O., Tal‐Yossef, Y., Mor, A., Aurbach, D., Lampert, J., Volkov, A., et al. (2015) · ChemElectroChem · doi:10.1002/celc.201500160 · Cited by 163
Studies on the Anode/Electrolyte Interfacein Lithium Ion Batteries
Winter, M., Appel, W. K., Evers, B., Hodal, T., Möller, K., Schneider, I., Wachtler, M., Wagner, M. R., Wrodnigg, G. H., & Besenhard, J. O. (2001) · Monatshefte für Chemie - Chemical Monthly · doi:10.1007/s007060170110 · Cited by 151
Aurbach, D., Srur-Lavi, O., Ghanty, C., Dixit, M., Haik, O., Talianker, M., Grinblat, Y., Leifer, N., Lavi, R., Major, D. T., et al. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0681506jes · Cited by 143
Lattice volume change during charge/discharge reaction and cycle performance of Li[NixCoyMnz]O2
Ishidzu, K., Yoshihiro, O. K. A., & Nakamura, T. (2016) · Solid State Ionics · doi:10.1016/j.ssi.2016.01.009 · Cited by 130
Berkes, B. B., Jozwiuk, A., Vračar, M., Sommer, H., Brezesinski, T., & Janek, J. (2015) · Analytical Chemistry · doi:10.1021/acs.analchem.5b01237 · Cited by 122
Self-citationBerkes, B. B., Jozwiuk, A., Sommer, H., Brezesinski, T., & Janek, J. (2015) · Electrochemistry Communications · doi:10.1016/j.elecom.2015.08.002 · Cited by 80
Self-citationFirst-cycle irreversibility of layered Li–Ni–Co–Mn oxide cathode in Li-ion batteries
Kang, S., Abraham, D. P., Yoon, W., Nam, K., & Yang, X. (2008) · Electrochimica Acta · doi:10.1016/j.electacta.2008.07.007 · Cited by 72
Shin, Y. J., Choi, W., HONG, Y., YOON, S., RYU, K., & CHANG, S. (2006) · Solid State Ionics · doi:10.1016/j.ssi.2005.11.019 · Cited by 53
Bie, X., Du, F., Wang, Y., Zhu, K., Ehrenberg, H., Nikolowski, K., Wang, C., Chen, G., & Wei, Y. (2013) · Electrochimica Acta · doi:10.1016/j.electacta.2013.02.131 · Cited by 35
de Biasi, L., Lieser, G., Rana, J., Indris, S., Dräger, C., Glatthaar, S., Mönig, R., Ehrenberg, H., Schumacher, G., Binder, J. R., et al. (2015) · CrystEngComm · doi:10.1039/c5ce00989h · Cited by 25
Self-citationCook, J. B., Kim, C., Xu, L., & Cabana, J. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.048301jes · Cited by 19
Cited by
Ryu, H.-H., Park, K.-J., Yoon, C. S., & Sun, Y.-K. (2018) · Chemistry of Materials · doi:10.1021/acs.chemmater.7b05269 · Cited by 1,629
Tian, Y., Zeng, G., Rutt, A., Shi, T., Kim, H., Wang, J., Koettgen, J., Sun, Y., Ouyang, B., Chen, T., et al. (2021) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00767 · Cited by 1,614
High entropy oxides for reversible energy storage
Sarkar, A., Velasco, L., Wang, D., Wang, Q., Talasila, G., de Biasi, L., Kübel, C., Brezesinski, T., Bhattacharya, S. S., Hahn, H., et al. (2018) · Nature Communications · doi:10.1038/s41467-018-05774-5 · Cited by 1,351
Self-citationFast Charging of Lithium‐Ion Batteries: A Review of Materials Aspects
Weiss, M., Ruess, R., Kasnatscheew, J., Levartovsky, Y., Levy, N. R., Minnmann, P., Stolz, L., Waldmann, T., Wohlfahrt‐Mehrens, M., Aurbach, D., et al. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202101126 · Cited by 1,055
Self-citationKoerver, R., Aygün, I., Leichtweiß, T., Dietrich, C., Zhang, W., Binder, J. O., Hartmann, P., Zeier, W. G., & Janek, J. (2017) · Chemistry of Materials · doi:10.1021/acs.chemmater.7b00931 · Cited by 1,020
Self-citation
Metadata
- Authors
- Kondrakov, A. O., Schmidt, A., Xu, J., Geßwein, H., Mönig, R., Hartmann, P., Sommer, H., Brezesinski, T., & Janek, J.
- Venue
- The Journal of Physical Chemistry C
- Publisher
- American Chemical Society (ACS)
- Published
- 2017-02-03
- Volume
- 121
- Issue
- 6
- Pages
- 3286-3294
- ISSN
- 1932-7447 (ISSN-L)
- 1932-7455
- OpenAlex
- W2573869881
- Cited by
- 701
- References
- 28
- FWCI
- 18.57
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.