The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index.
High-Performance Lignin-Containing Polyurethane Elastomers with Dynamic Covalent Polymer Networks
Abstract
High-performance lignin-containing polyurethane elastomers (LPUes) were successfully synthesized via partially substituting petroleum-derived polyols with depolymerized enzymatic hydrolysis lignin (DEL). The influences of DEL on the structure, thermostability, mechanical performance, and thermal reprocessability of LPUes were systematically studied. The tensile strength and toughness of PUes were significantly enhanced after the introduction of DEL, with the maximum tensile strength reaching up to 60.7 MPa and the toughness up to 263.6 MJ/m 3 . The enhancement for the strength and toughness was attributed to the dual cross-linking network structure and the interfacial hydrogen bonds between lignin and the PU matrix, which were demonstrated to facilitate the orientation of chain segments and lead to strain-induced crystallization and self-reinforcement. LPUes also exhibited much better elasticity than the control sample without lignin and could maintain excellent mechanical performance after being hot reprocessed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Silica-Like Malleable Materials from Permanent Organic Networks
Montarnal, D., Capelot, M., Tournilhac, F., & Leibler, L. (2011) · Science · doi:10.1126/science.1212648 · Cited by 3,625
Covalent adaptable networks: smart, reconfigurable and responsive network systems
Kloxin, C. J., & Bowman, C. N. (2013) · Chem. Soc. Rev. · doi:10.1039/c3cs60046g · Cited by 1,370
Delebecq, E., Pascault, J.-P., Boutevin, B., & Ganachaud, F. (2013) · Chemical Reviews · doi:10.1021/cr300195n · Cited by 1,326
Polyurethanes: Versatile Materials and Sustainable Problem Solvers for Today’s Challenges
Engels, H., Pirkl, H., Albers, R., Albach, R. W., Krause, J., Hoffmann, A., Casselmann, H., & Dormish, J. (2013) · Angewandte Chemie International Edition · doi:10.1002/anie.201302766 · Cited by 1,234
Dynamic Covalent Polymer Networks: from Old Chemistry to Modern Day Innovations
Zou, W., Dong, J., Luo, Y., Zhao, Q., & Xie, T. (2017) · Advanced Materials · doi:10.1002/adma.201606100 · Cited by 1,014
Dynamic urea bond for the design of reversible and self-healing polymers
Ying, H., Zhang, Y., & Cheng, J. (2014) · Nature Communications · doi:10.1038/ncomms4218 · Cited by 988
Constant, S., Wienk, H. L. J., Frissen, A. E., Peinder, P. D., Boelens, R., van Es, D. S., Grisel, R. J. H., Weckhuysen, B. M., Huijgen, W. J. J., Gosselink, R. J. A., et al. (2016) · Green Chemistry · doi:10.1039/c5gc03043a · Cited by 893
Mouldable liquid-crystalline elastomer actuators with exchangeable covalent bonds
Pei, Z., Yang, Y., Chen, Q., Terentjev, E. M., Wei, Y., & Ji, Y. (2014) · Nature Materials · doi:10.1038/nmat3812 · Cited by 886
Granata, A., & Argyropoulos, D. S. (1995) · Journal of Agricultural and Food Chemistry · doi:10.1021/jf00054a023 · Cited by 861
Superior Toughness and Fast Self‐Healing at Room Temperature Engineered by Transparent Elastomers
Kim, S., Jeon, H., Shin, S., Park, S., Jegal, J., Hwang, S. Y., Oh, D. X., & Park, J. (2018) · Advanced Materials · doi:10.1002/adma.201705145 · Cited by 857
Zhang, Z. P., Rong, M. Z., & Zhang, M. Q. (2018) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.03.002 · Cited by 586
Lei, Z. Q., Xiang, H. P., Yuan, Y. J., Rong, M. Z., & Zhang, M. Q. (2014) · Chemistry of Materials · doi:10.1021/cm4040616 · Cited by 578
Making Insoluble Polymer Networks Malleable via Olefin Metathesis
Lu, Y.-X., Tournilhac, F., Leibler, L., & Guan, Z. (2012) · Journal of the American Chemical Society · doi:10.1021/ja303356z · Cited by 568
Lu, Y.-X., & Guan, Z. (2012) · Journal of the American Chemical Society · doi:10.1021/ja306287s · Cited by 545
Hydrogen Bonding in Lignin: A Fourier Transform Infrared Model Compound Study
Kubo, S., & Kadla, J. F. (2005) · Biomacromolecules · doi:10.1021/bm050288q · Cited by 515
Mahmood, N., Yuan, Z., Schmidt, J., & Xu, C. (. (2016) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2016.01.037 · Cited by 487
Mattia, J., & Painter, P. (2007) · Macromolecules · doi:10.1021/ma0626362 · Cited by 477
Tough Self‐Healing Elastomers by Molecular Enforced Integration of Covalent and Reversible Networks
Wu, J., Cai, L., & Weitz, D. A. (2017) · Advanced Materials · doi:10.1002/adma.201702616 · Cited by 437
Disulfide exchange: exposing supramolecular reactivity through dynamic covalent chemistry
Black, S. P., Sanders, J. K. M., & Stefankiewicz, A. R. (2014) · Chem. Soc. Rev. · doi:10.1039/c3cs60326a · Cited by 405
Korley, L. T. J., Pate, B. D., Thomas, E. L., & Hammond, P. T. (2006) · Polymer · doi:10.1016/j.polymer.2006.02.093 · Cited by 366
Quantitative Phosphorus-31 NMR Analysis of Lignins, a New Tool for the Lignin Chemist
Argyropoulos, D. S. (1994) · Journal of Wood Chemistry and Technology · doi:10.1080/02773819408003085 · Cited by 280
Bio‐Inspired High‐Performance and Recyclable Cross‐Linked Polymers
Yu, S., Zhang, R., Wu, Q., Chen, T., & Sun, P. (2013) · Advanced Materials · doi:10.1002/adma.201301513 · Cited by 270
Small‐angle X‐ray scattering studies of microdomain structure in segmented polyurethane elastomers
Koberstein, J. T., & Stein, R. S. (1983) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1983.180210814 · Cited by 264
Martin, R., Rekondo, A., Ruiz de Luzuriaga, A., Cabañero, G., Grande, H. J., & Odriozola, I. (2014) · Journal of Materials Chemistry A · doi:10.1039/c3ta14927g · Cited by 263
Zheng, N., Hou, J., Xu, Y., Fang, Z., Zou, W., Zhao, Q., & Xie, T. (2017) · ACS Macro Letters · doi:10.1021/acsmacrolett.7b00037 · Cited by 237
Microphase Separation and Rheological Properties of Polyurethane Melts. 1. Effect of Block Length
Velankar, S., & Cooper, S. L. (1998) · Macromolecules · doi:10.1021/ma9811472 · Cited by 226
Chen, X., Li, L., Jin, K., & Torkelson, J. M. (2017) · Polym. Chem. · doi:10.1039/c7py01160a · Cited by 226
Composition of non-woody plant lignins and cinnamic acids by Py-GC/MS, Py/TMAH and FT-IR
del Río, J. C., Gutiérrez, A., Rodríguez, I. M., Ibarra, D., & Martínez, Á. T. (2007) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.09.003 · Cited by 224
Fang, Z., Zheng, N., Zhao, Q., & Xie, T. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b05713 · Cited by 222
Polyurethane Coatings Based on Chemically Unmodified Fractionated Lignin
Griffini, G., Passoni, V., Suriano, R., Levi, M., & Turri, S. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00073 · Cited by 210
Septevani, A. A., Evans, D. A. C., Chaleat, C., Martin, D. J., & Annamalai, P. K. (2015) · Industrial Crops and Products · doi:10.1016/j.indcrop.2014.11.053 · Cited by 195
Development of lignin-based polyurethane thermoplastics
Saito, T., Perkins, J. H., Jackson, D. C., Trammel, N. E., Hunt, M. A., & Naskar, A. K. (2013) · RSC Advances · doi:10.1039/c3ra44794d · Cited by 173
Properties and Morphology of Segmented Copoly(ether urea)s with Uniform Hard Segments
Versteegen, R. M., Kleppinger, R., Sijbesma, R. P., & Meijer, E. W. (2006) · Macromolecules · doi:10.1021/ma051874e · Cited by 160
Li, J., Zhang, G., Deng, L., Zhao, S., Gao, Y., Jiang, K., Sun, R., & Wong, C. (2014) · Journal of Materials Chemistry A · doi:10.1039/c4ta04941a · Cited by 153
Open cell semi-rigid polyurethane foams synthesized using palm oil-based bio-polyol
Marcovich, N. E., Kurańska, M., Prociak, A., Malewska, E., & Kulpa, K. (2017) · Industrial Crops and Products · doi:10.1016/j.indcrop.2017.03.025 · Cited by 134
Alagi, P., Choi, Y. J., & Hong, S. C. (2016) · European Polymer Journal · doi:10.1016/j.eurpolymj.2016.03.003 · Cited by 131
Highly Resilient Lignin-Containing Polyurethane Foam
Wang, S., Liu, W., Yang, D., & Qiu, X. (2018) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.8b05072 · Cited by 130
Self-citationHigh bio-content polyurethane composites with urethane modified lignin as filler
Zhang, C., Wu, H., & Kessler, M. R. (2015) · Polymer · doi:10.1016/j.polymer.2015.05.046 · Cited by 128
Enhancing polyurethane properties via soft segment crystallization
Sonnenschein, M. F., Lysenko, Z., Brune, D. A., Wendt, B. L., & Schrock, A. K. (2005) · Polymer · doi:10.1016/j.polymer.2005.08.006 · Cited by 109
A thermal self-healing polyurethane thermoset based on phenolic urethane
Cao, S. J., Li, S., Li, M., Xu, L., Ding, H., Xia, J., Zhang, M., & Huang, K. (2017) · Polymer Journal · doi:10.1038/pj.2017.48 · Cited by 105
High Performance Thermoplastic Elastomers with Biomass Lignin as Plastic Phase
Huang, J., Liu, W., & Qiu, X. (2019) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.8b04936 · Cited by 101
Self-citationChen, J., Hu, D., Li, Y., Meng, F., Zhu, J., & Zeng, J. (2018) · Polymer · doi:10.1016/j.polymer.2018.04.013 · Cited by 88
Nuclear Magnetic Resonance Studies. 4. Analysis of Residual Lignin after Kraft Pulping
Froass, P. M., Ragauskas, A. J., & Jiang, J.-E. (1998) · Industrial & Engineering Chemistry Research · doi:10.1021/ie970812c · Cited by 70
Bonab, V. S., Karimkhani, V., & Manas‐Zloczower, I. (2018) · Macromolecular Materials and Engineering · doi:10.1002/mame.201800405 · Cited by 64
Zhang, J., Chen, J., Yao, M., Jiang, Z., & Ma, Y. (2019) · Journal of Applied Polymer Science · doi:10.1002/app.47673 · Cited by 33
A biomass approach to mendable bio-elastomers
Yuan, L., Wang, Z., Ganewatta, M. S., Rahman, M. A., Lamm, M. E., & Tang, C. (2017) · Soft Matter · doi:10.1039/c6sm02003h · Cited by 29
Wang, W., Chen, H., Dai, Q., Zhao, D., Zhou, Y., Wang, L., & Zeng, D. (2018) · Smart Materials and Structures · doi:10.1088/1361-665x/aaebc8 · Cited by 16
Yu, X., Chen, E., Chengshen, Z. H. U., Suqin, H. E., & Liu, W. (2010) · Acta Polymerica Sinica · doi:10.3724/sp.j.1105.2010.10048 · Cited by 2
Self-citation
Cited by
Li, Z., Zhu, Y., Niu, W., Yang, X., Jiang, Z., Lu, Z., Liu, X., & Sun, J. (2021) · Advanced Materials · doi:10.1002/adma.202101498 · Cited by 668
Wang, X., Zhan, S., Lu, Z., Li, J., Yang, X., Qiao, Y., Men, Y., & Sun, J. (2020) · Advanced Materials · doi:10.1002/adma.202005759 · Cited by 575
Zhang, C., Liang, H., Liang, D., Lin, Z., Chen, Q., Feng, P., & Wang, Q. (2021) · Angewandte Chemie International Edition · doi:10.1002/anie.202014299 · Cited by 319
Biobased vitrimers: Towards sustainable and adaptable performing polymer materials
Lucherelli, M. A., Duval, A., & Avérous, L. (2022) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2022.101515 · Cited by 291
Metadata
- Authors
- Liu, W., Fang, C., Wang, S., Huang, J., & Qiu, X.
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2019-08-21
- Volume
- 52
- Issue
- 17
- Pages
- 6474-6484
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- OpenAlex
- W2969772624
- Cited by
- 258
- References
- 48
- FWCI
- 8.38
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
