The DOI matches its Crossref record.
Direct in Vitro Electrospinning with Polymer Melts
Abstract
The electrospinning of polymer melts can offer an advantage over solution electrospinning, in the development of layered tissue constructs for tissue engineering. Melt electrospinning does not require a solvent, of which many are cytotoxic in nature, and the use of nonwater soluble polymers allows the collection of fibers on water or onto cells. In this article, melt electrospinning of a blend of PEO-block-PCL with PCL was performed with in vitro cultured fibroblasts as the collection target. The significant parameters governing electrospinning polymer melts were determined before electrospinning directly onto fibroblasts. In general, a high electric field resulted in the most homogeneous and smallest fibers, although it is important that an optimal pump rate to the spinneret needs to be determined for different configurations. Many parameters governing melt electrospinning differ to those reported for solution electrospinning: the pump rate was a magnitude lower and the viscosity a magnitude higher than successful parameters for solution electrospinning. Cell vitality was maintained throughout the electrospinning process. Six days after electrospinning, fibroblasts adhered to the electrospun fibers and appeared to detach from the underlying flat substrate. The morphology of the fibroblasts changed from spread and flat, to long and spindle-shaped as adherence onto the fiber progressed. Therefore, an important step for producing layer-on-layer tissue constructs of cells and polymers in view of scaffold construction for tissue engineering was successfully demonstrated. The process of using cultured cells as the collection target was termed "direct in vitro electrospinning".
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Electrospinning: A fascinating fiber fabrication technique
Bhardwaj, N., & Kundu, S. C. (2010) · Biotechnology Advances · doi:10.1016/j.biotechadv.2010.01.004 · Cited by 5,028
Electrospinning and Electrospun Nanofibers: Methods, Materials, and Applications
Xue, J., Wu, T., Dai, Y., & Xia, Y. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00593 · Cited by 5,015
Electrospinning: A Fascinating Method for the Preparation of Ultrathin Fibers
Greiner, A., & Wendorff, J. H. (2007) · Angewandte Chemie International Edition · doi:10.1002/anie.200604646 · Cited by 4,241
A review on electrospinning design and nanofibre assemblies
Teo, W. E., & Ramakrishna, S. (2006) · Nanotechnology · doi:10.1088/0957-4484/17/14/r01 · Cited by 2,289
Canton, I., & Battaglia, G. (2012) · Chemical Society Reviews · doi:10.1039/c2cs15309b · Cited by 936
Electrospinning versus fibre production methods: from specifics to technological convergence
Luo, C. J., Stoyanov, S. D., Stride, E., Pelan, E., & Edirisinghe, M. (2012) · Chemical Society Reviews · doi:10.1039/c2cs35083a · Cited by 691
Melt electrospinning today: An opportune time for an emerging polymer process
Brown, T. D., Dalton, P. D., & Hutmacher, D. W. (2016) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2016.01.001 · Cited by 542
Self-citationProgress in the Field of Electrospinning for Tissue Engineering Applications
Agarwal, S., Wendorff, J. H., & Greiner, A. (2009) · Advanced Materials · doi:10.1002/adma.200803092 · Cited by 523
Melt blown nanofibers: Fiber diameter distributions and onset of fiber breakup
Ellison, C. J., Phatak, A., Giles, D. W., Macosko, C. W., & Bates, F. S. (2007) · Polymer · doi:10.1016/j.polymer.2007.04.005 · Cited by 497
Townsend-Nicholson, A., & Jayasinghe, S. N. (2006) · Biomacromolecules · doi:10.1021/bm060649h · Cited by 461
Wang, X.-X., Yu, G.-F., Zhang, J., Yu, M., Ramakrishna, S., & Long, Y.-Z. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100704 · Cited by 447
A Review of the Fundamental Principles and Applications of Solution Blow Spinning
Daristotle, J. L., Behrens, A. M., Sandler, A. D., & Kofinas, P. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b12994 · Cited by 443
A review on electrospun polymeric nanofibers: Production parameters and potential applications
Ibrahim, H. M., & Klingner, A. (2020) · Polymer Testing · doi:10.1016/j.polymertesting.2020.106647 · Cited by 402
Recent advances in nanofibre fabrication techniques
Nayak, R., Padhye, R., Kyratzis, I. L., Truong, Y. B., & Arnold, L. (2012) · Textile Research Journal · doi:10.1177/0040517511424524 · Cited by 375
Green Electrospun Nanofibers and Their Application in Air Filtration
Lv, D., Zhu, M., Jiang, Z., Jiang, S., Zhang, Q., Xiong, R., & Huang, C. (2018) · Macromolecular Materials and Engineering · doi:10.1002/mame.201800336 · Cited by 375
Materials for Smart Soft Actuator Systems
Apsite, I., Salehi, S., & Ionov, L. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.1c00453 · Cited by 357
Electrospinning of polymer melts: Phenomenological observations
Dalton, P. D., Grafahrend, D., Klinkhammer, K., Klee, D., & Möller, M. (2007) · Polymer · doi:10.1016/j.polymer.2007.09.037 · Cited by 357
Self-citationFabrication of Electrospun Polymer Nanofibers with Diverse Morphologies
Wang, C., Wang, J., Zeng, L., Qiao, Z., Liu, X., Liu, H., Zhang, J., & Ding, J. (2019) · Molecules · doi:10.3390/molecules24050834 · Cited by 331
Electrospinning Nanofibers for Therapeutics Delivery
Shahriar, S. M. S., Mondal, J., Hasan, M. N., Revuri, V., Lee, D. Y., & Lee, Y.-K. (2019) · Nanomaterials · doi:10.3390/nano9040532 · Cited by 301
Hutmacher, D. W., & Dalton, P. D. (2011) · Chemistry – An Asian Journal · doi:10.1002/asia.201000436 · Cited by 301
Self-citationThe Effect of Flow Rate on Morphology and Deposition Area of Electrospun Nylon 6 Nanofiber
Zargham, S., Bazgir, S., Tavakoli, A., Rashidi, A. S., & Damerchely, R. (2012) · Journal of Engineered Fibers and Fabrics · doi:10.1177/155892501200700414 · Cited by 282
Agarwal, S., Greiner, A., & Wendorff, J. H. (2009) · Advanced Functional Materials · doi:10.1002/adfm.200900591 · Cited by 265
Electrospinning and additive manufacturing: converging technologies
Dalton, P. D., Vaquette, C., Farrugia, B. L., Dargaville, T. R., Brown, T. D., & Hutmacher, D. W. (2013) · Biomater. Sci. · doi:10.1039/c2bm00039c · Cited by 264
Self-citationStrategic Design and Fabrication of Engineered Scaffolds for Articular Cartilage Repair
Izadifar, Z., Chen, X., & Kulyk, W. (2012) · Journal of Functional Biomaterials · doi:10.3390/jfb3040799 · Cited by 203
Porous carbon fabrication techniques: A review
Kobina Sam, D., Li, H., Xu, Y.-T., & Cao, Y. (2024) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2024.01.044 · Cited by 46
Metadata
- Authors
- Dalton, P. D., Klinkhammer, K., Salber, J., Klee, D., & Möller, M.
- Venue
- Biomacromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2006-02-14
- Volume
- 7
- Issue
- 3
- Pages
- 686-690
- ISSN
- 1525-7797 (ISSN-L)
- 1526-4602
- OpenAlex
- W1988392612
- Cited by
- 232
- References
- 0
- FWCI
- 6.11
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.