CoChat

Measurement of Air−Water Interfacial Area for Multiple Hysteretic Drainage Curves in an Unsaturated Fine Sand

Chen, Lixia, Kibbey, Tohren C. G. · 2006 · Langmuir
Cited by 64

The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.

Abstract

A new method has been developed to measure fluid-fluid interfacial area during multiple drainages, along with the measurement of hysteretic capillary pressure-saturation (P(c)-S) relationships in unsaturated porous media. The method makes use of an automated device which has been successfully used for rapid measurement of hysteretic P(c)-S relationships, in combination with a novel technique for interfacial area measurement. A pure anionic surfactant, sodium octylbenzene sulfonate (SOBS), is used as a surface-active tracer, and a flow-through UV spectrometer is used to monitor the real-time concentration change of SOBS solution due to adsorption to the fluid-fluid interface during drainage. The Gibbs and Langmuir adsorption equations are applied in combination with a continuous mole balance to calculate interfacial areas. Using this method, air-water interfacial area of a fine sand was measured as a function of capillary pressure and saturation during primary, secondary, and one scanning drainages to explore the influence of drying/wetting history on interfacial area. Results show that 8-20 and 12-22 cm(2)/g more air-water interface was generated in secondary and scanning drainages, respectively, than in primary drainage, with the magnitude of the difference varying as a function of saturation. An advantage of the method is that interfacial tension variations from the method itself are relatively small, typically on the order of 5 mN/m, so measured areas are not skewed by surface-tension-induced changes in interfacial area. In a measurement specifically designed to study the influence of surfactant-induced interfacial tension variations, approximately two times more interfacial area was observed for a 25 mN/m interfacial tension change, in comparison with a system with relatively constant interfacial tension. Implications of results of interfacial area measurements for hysteresis in the three-dimensional relationship between capillary pressure, saturation, and interfacial area are discussed.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1021/la053521e

Cites

1 of 1 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Cited by

See all 64

Metadata

Authors
Chen, L., & Kibbey, T. C. G.
Venue
Langmuir
Published
2006-06-27
Volume
22
Issue
16
Pages
6874-6880
ISSN
  • 0743-7463 (ISSN-L)
  • 1520-5827
OpenAlex
W2012862500
Cited by
64
References
1
FWCI
18.84
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.