The DOI matches its Crossref record; 43 of the 43 references it cites were found in a registry or an index.
New Insights on the Strain-Induced Mesophase of Poly(d,l-lactide): In Situ WAXS and DSC Study of the Thermo-Mechanical Stability
Abstract
This work deals with the study of the mesomorphic form or mesophase induced by tensile drawing from the amorphous state of a polylactide material containing 4 mol % of d -stereoisomer units. Investigations have been carried out over the draw temperature domain 45−90 °C, i.e. an interval spanning roughly ±20 °C about the glass transition temperature. In situ WAXS experiments during drawing, stress relaxation, and/or heating of stretched samples invariably showed the strain-induced occurrence of the mesophase as far as temperature did not exceed 70 °C. This seems to be the upper stability temperature of the mesophase identified in a previous study. DSC traces upon heating of drawn samples exhibit a post glass transition endothermic peak similar to the enthalpy relaxation phenomenon observed for aged polymers. The amplitude of this strain-induced endotherm proved to be strongly dependent on draw temperature and draw ratio. Draw ratio also appeared to strongly influence the temperature domain of cold crystallization. The quite different structural evolution of the drawn samples as a function of temperature, depending whether cold crystallization occurred close or far from the strain-induced endotherm, led us to the conclusion that this endotherm results from neither physical aging nor orientation relaxation but from “melting” of the mesophase. This proposal is thoroughly supported by the insensitivity of the endotherm enthalpy to the DSC scanning rate that gives evidence of a first order thermodynamic transition in contrast to the case of aging-induced endotherm. WAXS as a function of temperature on drawn samples annealed with free ends enabled to probe the persistence of chain orientation and the stability of the strain-induced structural changes in relation to drawing conditions.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The Theory of Polymer Dynamics
Marrucci, G. (1987) · Journal of Non-Newtonian Fluid Mechanics · doi:10.1016/0377-0257(87)85036-x · Cited by 9,749
The theory of polymer dynamics
Doi, M., & Edwards, S. F. (1986) · Cited by 8,928
An Overview of Polylactides as Packaging Materials
Auras, R., Harte, B., & Selke, S. (2004) · Macromolecular Bioscience · doi:10.1002/mabi.200400043 · Cited by 3,454
Processing technologies for poly(lactic acid)
Lim, L.-T., Auras, R., & Rubino, M. (2008) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2008.05.004 · Cited by 2,766
Fischer, E. W., Sterzel, H. J., & Wegner, G. (1973) · Kolloid-Zeitschrift und Zeitschrift für Polymere · doi:10.1007/bf01498927 · Cited by 1,704
Poly(lactic acid) fiber: An overview
Gupta, B., Revagade, N., & Hilborn, J. (2007) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2007.01.005 · Cited by 1,360
Hutchinson, J. M. (1995) · Progress in Polymer Science · doi:10.1016/0079-6700(94)00001-i · Cited by 1,045
Nano-biocomposites: Biodegradable polyester/nanoclay systems
BORDES, P., POLLET, E., & AVEROUS, L. (2009) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2008.10.002 · Cited by 1,033
Zhang, J., Tashiro, K., Tsuji, H., & Domb, A. J. (2008) · Macromolecules · doi:10.1021/ma0706071 · Cited by 913
Crystallization, structure and properties of plasticized poly(l-lactide)
Kulinski, Z., & Piorkowska, E. (2005) · Polymer · doi:10.1016/j.polymer.2005.07.101 · Cited by 540
Crystallization and Melting Behavior of Polylactides
Sarasua, J.-R., Prud'homme, R. E., Wisniewski, M., Le Borgne, A., & Spassky, N. (1998) · Macromolecules · doi:10.1021/ma971545p · Cited by 525
The Case for Polylactic Acid as a Commodity Packaging Plastic
Sinclair, R. G. (1996) · Journal of Macromolecular Science, Part A · doi:10.1080/10601329608010880 · Cited by 453
Thermal analysis of the double‐melting behavior of poly(L‐lactic acid)
Yasuniwa, M., Tsubakihara, S., Sugimoto, Y., & Nakafuku, C. (2004) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.10674 · Cited by 375
Heat capacity of poly(lactic acid)
Pyda, M., Bopp, R. C., & Wunderlich, B. (2004) · The Journal of Chemical Thermodynamics · doi:10.1016/j.jct.2004.05.003 · Cited by 333
Preparation and Properties of Plasticized Poly(lactic acid) Films
Ljungberg, N., & Wesslén, B. (2005) · Biomacromolecules · doi:10.1021/bm050098f · Cited by 331
Enthalpy Relaxation and Embrittlement of Poly( l -lactide) during Physical Aging
Pan, P., Zhu, B., & Inoue, Y. (2007) · Macromolecules · doi:10.1021/ma071737c · Cited by 282
Strain-Induced Molecular Ordering in Polylactide upon Uniaxial Stretching
Stoclet, G., Seguela, R., Lefebvre, J. M., Elkoun, S., & Vanmansart, C. (2010) · Macromolecules · doi:10.1021/ma9024366 · Cited by 266
Self-citationEnergy storage during inelastic deformation of glassy polymers
Hasan, O. A., & Boyce, M. C. (1993) · Polymer · doi:10.1016/0032-3861(93)90252-6 · Cited by 229
Solarski, S., Ferreira, M., & Devaux, E. (2005) · Polymer · doi:10.1016/j.polymer.2005.10.027 · Cited by 190
Thermal properties and physical ageing of poly (l-lactic acid)
Celli, A., & Scandola, M. (1992) · Polymer · doi:10.1016/0032-3861(92)90440-8 · Cited by 188
Crystallization and Microstructure of Poly(l-lactide-co-meso-lactide) Copolymers
Huang, J., Lisowski, M. S., Runt, J., Hall, E. S., Kean, R. T., Buehler, N., & Lin, J. S. (1998) · Macromolecules · doi:10.1021/ma9714629 · Cited by 187
Influence of biaxial stretching mode on the crystalline texture in polylactic acid films
Ou, X., & Cakmak, M. (2008) · Polymer · doi:10.1016/j.polymer.2008.09.053 · Cited by 130
Zhang, J., Duan, Y., Domb, A. J., & Ozaki, Y. (2010) · Macromolecules · doi:10.1021/ma100301h · Cited by 129
Magoń, A., & Pyda, M. (2009) · Polymer · doi:10.1016/j.polymer.2009.06.052 · Cited by 121
Schwach, E., Six, J., & Avérous, L. (2008) · Journal of Polymers and the Environment · doi:10.1007/s10924-008-0107-6 · Cited by 112
Crystalline and supermolecular structure of polylactide in relation to the crystallization method
Pluta, M., & Gałęski, A. (2002) · Journal of Applied Polymer Science · doi:10.1002/app.11280 · Cited by 108
Orientation prior to crystallisation during drawing of poly(ethylene terephthalate)
Blundell, D. J., Mahendrasingam, A., Martin, C., Fuller, W., Mackerron, D. H., Harvie, J. L., Oldman, R. J., & Riekel, C. (2000) · Polymer · doi:10.1016/s0032-3861(00)00128-2 · Cited by 107
Pyda, M., & Wunderlich, B. (2005) · Macromolecules · doi:10.1021/ma051611k · Cited by 104
Nonlinear Mechanooptical Behavior of Uniaxially Stretched Poly(lactic acid): Dynamic Phase Behavior
Mulligan, J. H., & Çakmak, M. (2005) · Macromolecules · doi:10.1021/ma048794f · Cited by 97
Aou, K., Kang, S., & Hsu, S. L. (2005) · Macromolecules · doi:10.1021/ma051022e · Cited by 94
Structure development and biodegradability of uniaxially stretched poly(l-lactide)
Lee, J. K., Lee, K. H., & Jin, B. S. (2001) · European Polymer Journal · doi:10.1016/s0014-3057(00)00213-5 · Cited by 85
Plastic deformation and mobility in glassy polymers
Oleinik, E. F. (2007) · Steinkopff eBooks · doi:10.1007/bfb0115425 · Cited by 73
Séguéla, R. (2005) · Journal of macromolecular science. Part C, Reviews in macromolecular chemistry and physics/Journal of macromolecular science. Reviews in macromolecular chemistry and physics · doi:10.1081/mc-200067727 · Cited by 58
Aou, K., Hsu, S. L., Kleiner, L. W., & Tang, F.-W. (2007) · The Journal of Physical Chemistry B · doi:10.1021/jp074509t · Cited by 54
Yang, X., Kang, S., Yang, Y., Aou, K., & Hsu, S. L. (2004) · Polymer · doi:10.1016/j.polymer.2004.03.107 · Cited by 54
Plastic Deformation of Amorphous Poly( l / dl -lactide): Structure Evolution and Physical Properties
Pluta, M., & Gałęski, A. (2007) · Biomacromolecules · doi:10.1021/bm061229v · Cited by 50
Recovery of deformed polymers. III. Thermal properties
Park, J. B., & UHLMANN, D. R. (1973) · Journal of Applied Physics · doi:10.1063/1.1661862 · Cited by 48
Spectroscopic Evidence of Melting of Ordered Structures in the Aged Glassy Poly( l -lactide)
Na, B., Lv, R., Zou, S., Li, Z., Tian, N., & Fu, Q. (2010) · Macromolecules · doi:10.1021/ma100012c · Cited by 45
Strain-Induced Enthalpy Relaxation in Poly(lactic acid)
Lee, S. C., Han, J. I., Jeong, Y. G., & Kwon, M. (2009) · Macromolecules · doi:10.1021/ma901880a · Cited by 36
Structure development of poly( L ‐lactic acid) fibers processed at various spinning conditions
Ghosh, S., & Vasanthan, N. (2006) · Journal of Applied Polymer Science · doi:10.1002/app.24104 · Cited by 34
Effects of take‐up speed on the structure and properties of melt‐spun poly( L ‐lactic acid) fibers
Kim, M. S., Kim, J. C., & Kim, Y. H. (2008) · Polymers for Advanced Technologies · doi:10.1002/pat.1026 · Cited by 24
Crystallization and Mechanical Propertiesof Poly (D, L) Lactide-based Blown Films
Stoclet, G., Elkoun, S., Gaucher, V., Séguéla, R., & Lefebvre, J. (2007) · International Polymer Processing · doi:10.3139/217.2066 · Cited by 15
Self-citation
Cited by
Zheng, Y., & Pan, P. (2020) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2020.101291 · Cited by 229
Why Is Crystalline Poly(lactic acid) Brittle at Room Temperature?
Razavi, M., & Wang, S.-Q. (2019) · Macromolecules · doi:10.1021/acs.macromol.9b00595 · Cited by 212
Tashiro, K., Kouno, N., Wang, H., & Tsuji, H. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b01468 · Cited by 143
Zhou, C., Li, H., Zhang, W., Li, J., Huang, S., Meng, Y., Christiansen, J. D., Yu, D., Wu, Z., & Jiang, S. (2016) · Polymer · doi:10.1016/j.polymer.2016.03.014 · Cited by 85
Xiong, Z., Liu, G., Zhang, X., Wen, T., de Vos, S., Joziasse, C., & Wang, D. (2013) · Polymer · doi:10.1016/j.polymer.2012.11.076 · Cited by 83
Metadata
- Authors
- Stoclet, G., Seguela, R., Lefebvre, J.-M., & Rochas, C.
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 2010-08-11
- Volume
- 43
- Issue
- 17
- Pages
- 7228-7237
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- OpenAlex
- W2040296902
- Cited by
- 271
- References
- 43
- FWCI
- 8.64
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.