The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Enhanced Mechanical Properties of Nanocomposites at Low Graphene Content
Abstract
In this study, the mechanical properties of epoxy nanocomposites with graphene platelets, single-walled carbon nanotubes, and multi-walled carbon nanotube additives were compared at a nanofiller weight fraction of 0.1 +/- 0.002%. The mechanical properties measured were the Young's modulus, ultimate tensile strength, fracture toughness, fracture energy, and the material's resistance to fatigue crack propagation. The results indicate that graphene platelets significantly out-perform carbon nanotube additives. The Young's modulus of the graphene nanocomposite was approximately 31% greater than the pristine epoxy as compared to approximately 3% increase for single-walled carbon nanotubes. The tensile strength of the baseline epoxy was enhanced by approximately 40% with graphene platelets compared to approximately 14% improvement for multi-walled carbon nanotubes. The mode I fracture toughness of the nanocomposite with graphene platelets showed approximately 53% increase over the epoxy compared to approximately 20% improvement for multi-walled carbon nanotubes. The fatigue resistance results also showed significantly different trends. While the fatigue suppression response of nanotube/epoxy composites degrades dramatically as the stress intensity factor amplitude is increased, the reverse effect is seen for graphene-based nanocomposites. The superiority of graphene platelets over carbon nanotubes in terms of mechanical properties enhancement may be related to their high specific surface area, enhanced nanofiller-matrix adhesion/interlocking arising from their wrinkled (rough) surface, as well as the two-dimensional (planar) geometry of graphene platelets.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Electric Field Effect in Atomically Thin Carbon Films
Novoselov, K. S., Geim, A. K., Morozov, S. V., Jiang, D., Zhang, Y., Dubonos, S. V., Grigorieva, I. V., & Firsov, A. A. (2004) · Science · doi:10.1126/science.1102896 · Cited by 66,834
Graphene-based composite materials
Stankovich, S., Dikin, D. A., Dommett, G. H. B., Kohlhaas, K. M., Zimney, E. J., Stach, E. A., Piner, R. D., Nguyen, S. T., & Ruoff, R. S. (2006) · Nature · doi:10.1038/nature04969 · Cited by 12,922
Cited by
Dispersion and functionalization of carbon nanotubes for polymer-based nanocomposites: A review
Ma, P.-C., Siddiqui, N. A., Marom, G., & Kim, J.-K. (2010) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2010.07.003 · Cited by 3,414
Graphene/Polymer Nanocomposites
Kim, H., Abdala, A. A., & Macosko, C. W. (2010) · Macromolecules · doi:10.1021/ma100572e · Cited by 3,406
Graphene-based polymer nanocomposites
Potts, J. R., Dreyer, D. R., Bielawski, C. W., & Ruoff, R. S. (2011) · Polymer · doi:10.1016/j.polymer.2010.11.042 · Cited by 3,123
Mechanical properties of graphene and graphene-based nanocomposites
Papageorgiou, D. G., Kinloch, I. A., & Young, R. J. (2017) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.07.004 · Cited by 2,579
Environmental applications of graphene-based nanomaterials
Perreault, F., Fonseca de Faria, A., & Elimelech, M. (2015) · Chemical Society Reviews · doi:10.1039/c5cs00021a · Cited by 1,528
A review on carbon nanotubes and graphene as fillers in reinforced polymer nanocomposites
Mittal, G., Dhand, V., Rhee, K. Y., Park, S.-J., & Lee, W. R. (2015) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2014.03.022 · Cited by 1,371
The mechanics of graphene nanocomposites: A review
Young, R. J., Kinloch, I. A., Gong, L., & Novoselov, K. S. (2012) · Composites Science and Technology · doi:10.1016/j.compscitech.2012.05.005 · Cited by 1,294
Sengupta, R., Bhattacharya, M., Bandyopadhyay, S., & Bhowmick, A. K. (2011) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2010.11.003 · Cited by 1,283
Tjong, S. C. (2013) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2013.08.001 · Cited by 1,155
Graphene-polymer nanocomposites for structural and functional applications
Hu, K., Kulkarni, D. D., Choi, I., & Tsukruk, V. V. (2014) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2014.03.001 · Cited by 1,085
Functional Composite Materials Based on Chemically Converted Graphene
Bai, H., Li, C., & Shi, G. (2011) · Advanced Materials · doi:10.1002/adma.201003753 · Cited by 1,080
Mechanical properties and microstructure of a graphene oxide–cement composite
Pan, Z., He, L., Qiu, L., Korayem, A. H., Li, G., Zhu, J. W., Collins, F., Li, D., Duan, W. H., & Wang, M. C. (2015) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2015.02.001 · Cited by 909
Yang, S.-Y., Lin, W.-N., Huang, Y.-L., Tien, H.-W., Wang, J.-Y., Ma, C.-C. M., Li, S.-M., & Wang, Y.-S. (2011) · Carbon · doi:10.1016/j.carbon.2010.10.014 · Cited by 906
Dorri Moghadam, A., Omrani, E., Menezes, P. L., & Rohatgi, P. K. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.03.014 · Cited by 906
Zhao, S., Zhang, H.-B., Luo, J.-Q., Wang, Q.-W., Xu, B., Hong, S., & Yu, Z.-Z. (2018) · ACS Nano · doi:10.1021/acsnano.8b05739 · Cited by 893
Self-citationWan, Y.-J., Tang, L.-C., Gong, L.-X., Yan, D., Li, Y.-B., Wu, L.-B., Jiang, J.-X., & Lai, G.-Q. (2014) · Carbon · doi:10.1016/j.carbon.2013.12.050 · Cited by 788
Reinforcing Effects of Graphene Oxide on Portland Cement Paste
Gong, K., Pan, Z., Korayem, A. H., Qiu, L., Li, D., Collins, F., Wang, C. M., & Duan, W. H. (2015) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001125 · Cited by 772
Hwang, J., Yoon, T., Jin, S. H., Lee, J., Kim, T., Hong, S. H., & Jeon, S. (2013) · Advanced Materials · doi:10.1002/adma.201302495 · Cited by 766
Well-Dispersed Chitosan/Graphene Oxide Nanocomposites
Yang, X., Tu, Y., Li, L., Shang, S., & Tao, X.-M. (2010) · ACS Applied Materials & Interfaces · doi:10.1021/am100222m · Cited by 755
Polymer Nanocomposites—A Comparison between Carbon Nanotubes, Graphene, and Clay as Nanofillers
Bhattacharya, M. (2016) · Materials · doi:10.3390/ma9040262 · Cited by 747
Effect of defects on the intrinsic strength and stiffness of graphene
Zandiatashbar, A., Lee, G.-H., An, S. J., Lee, S., Mathew, N., Terrones, M., Hayashi, T., Picu, C. R., Hone, J., & Koratkar, N. (2014) · Nature Communications · doi:10.1038/ncomms4186 · Cited by 743
Self-citationNovel anticorrosion coatings prepared from polyaniline/graphene composites
Chang, C.-H., Huang, T.-C., Peng, C.-W., Yeh, T.-C., Lu, H.-I., Hung, W.-I., Weng, C.-J., Yang, T.-I., & Yeh, J.-M. (2012) · Carbon · doi:10.1016/j.carbon.2012.06.043 · Cited by 728
Interfacial Microstructure and Properties of Carbon Fiber Composites Modified with Graphene Oxide
Zhang, X., Fan, X., Yan, C., Li, H., Zhu, Y., Li, X., & Yu, L. (2012) · ACS Applied Materials & Interfaces · doi:10.1021/am201757v · Cited by 673
In situ Polymerization Approach to Graphene-Reinforced Nylon-6 Composites
Xu, Z., & Gao, C. (2010) · Macromolecules · doi:10.1021/ma1009337 · Cited by 667
Song, P., Cao, Z., Cai, Y., Zhao, L., Fang, Z., & Fu, S. (2011) · Polymer · doi:10.1016/j.polymer.2011.06.045 · Cited by 623
Zhang, A., & Lieber, C. M. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00608 · Cited by 621
Fabrication, Mechanical Properties, and Biocompatibility of Graphene-Reinforced Chitosan Composites
Fan, H., Wang, L., Zhao, K., Li, N., Shi, Z., Ge, Z., & Jin, Z. (2010) · Biomacromolecules · doi:10.1021/bm100470q · Cited by 554
Carbon‐Based Photothermal Actuators
Han, B., Zhang, Y., Chen, Q., & Sun, H. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201802235 · Cited by 522
Feng, C., Kitipornchai, S., & Yang, J. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.024 · Cited by 423
Mechanisms of mechanical reinforcement by graphene and carbon nanotubes in polymer nanocomposites
Papageorgiou, D. G., Li, Z., Liu, M., Kinloch, I. A., & Young, R. J. (2020) · Nanoscale · doi:10.1039/c9nr06952f · Cited by 423
Preparation of Covalently Functionalized Graphene Using Residual Oxygen-Containing Functional Groups
Hsiao, M.-C., Liao, S.-H., Yen, M.-Y., Liu, P.-I., Pu, N.-W., Wang, C.-A., & Ma, C.-C. M. (2010) · ACS Applied Materials & Interfaces · doi:10.1021/am100597d · Cited by 414
Wang, X., Xing, W., Zhang, P., Song, L., Yang, H., & Hu, Y. (2012) · Composites Science and Technology · doi:10.1016/j.compscitech.2012.01.027 · Cited by 408
Harris, K. D., Elias, A. L., & Chung, H.-J. (2016) · Journal of Materials Science · doi:10.1007/s10853-015-9643-3 · Cited by 403
Wu, S., Ladani, R. B., Zhang, J., Bafekrpour, E., Ghorbani, K., Mouritz, A. P., Kinloch, A. J., & Wang, C. H. (2015) · Carbon · doi:10.1016/j.carbon.2015.07.026 · Cited by 393
Chen, D., Yang, J., & Kitipornchai, S. (2017) · Composites Science and Technology · doi:10.1016/j.compscitech.2017.02.008 · Cited by 388
Evolution from graphite to graphene elastomer composites
Sadasivuni, K. K., Ponnamma, D., Thomas, S., & Grohens, Y. (2014) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.08.003 · Cited by 379
Epoxy Toughening with Low Graphene Loading
Park, Y. T., Qian, Y., Chan, C., Suh, T., Nejhad, M. G., Macosko, C. W., & Stein, A. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201402553 · Cited by 362
Wan, Y.-J., Tang, L.-C., Yan, D., Zhao, L., Li, Y.-B., Wu, L.-B., Jiang, J.-X., & Lai, G.-Q. (2013) · Composites Science and Technology · doi:10.1016/j.compscitech.2013.04.009 · Cited by 358
Review of functionalization, structure and properties of graphene/polymer composite fibers
Ji, X., Xu, Y., Zhang, W., Cui, L., & Liu, J. (2016) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2016.04.011 · Cited by 351
Nanostructured metal oxides and its hybrids for photocatalytic and biomedical applications
Kannan, K., Radhika, D., Sadasivuni, K. K., Reddy, K. R., & Raghu, A. V. (2020) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2020.102178 · Cited by 341
Baradaran, S., Moghaddam, E., Basirun, W. J., Mehrali, M., Sookhakian, M., Hamdi, M., Moghaddam, M. R. N., & Alias, Y. (2014) · Carbon · doi:10.1016/j.carbon.2013.11.054 · Cited by 340
Jia, J., Sun, X., Lin, X., Shen, X., Mai, Y.-W., & Kim, J.-K. (2014) · ACS Nano · doi:10.1021/nn500590g · Cited by 332
Huang, L., Yi, N., Wu, Y., Zhang, Y., Zhang, Q., Huang, Y., Ma, Y., & Chen, Y. (2013) · Advanced Materials · doi:10.1002/adma.201204768 · Cited by 329
Investigating aluminum alloy reinforced by graphene nanoflakes
Yan, S. J., Dai, S. L., Zhang, X. Y., Yang, C., Hong, Q. H., Chen, J. Z., & Lin, Z. M. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.06.077 · Cited by 329
Song, M., Yang, J., & Kitipornchai, S. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2017.09.043 · Cited by 326
Wu, H., Yang, J., & Kitipornchai, S. (2017) · Composite Structures · doi:10.1016/j.compstruct.2016.12.001 · Cited by 316
Polymer matrix nanocomposites for automotive structural components
Naskar, A. K., Keum, J. K., & Boeman, R. G. (2016) · Nature Nanotechnology · doi:10.1038/nnano.2016.262 · Cited by 316
Zakaria, M. R., Abdul Kudus, M. H., Md. Akil, H., & Mohd Thirmizir, M. Z. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2017.03.023 · Cited by 305
Graphene Nanoribbon Composites
Reif, J., Lu, W., Thomas, A. V., Zandiatashbar, A., Rafiee, J., Tour, J. M., & Koratkar, N. A. (2010) · ACS Nano · doi:10.1021/nn102529n · Cited by 304
Self-citationDong, Y. H., Li, Y. H., Chen, D., & Yang, J. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.03.009 · Cited by 298
Zhang, X., Zhao, N., & He, C. (2020) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100672 · Cited by 293
Wang, J.-Y., Yang, S.-Y., Huang, Y.-L., Tien, H.-W., Chin, W.-K., & Ma, C.-C. M. (2011) · Journal of Materials Chemistry · doi:10.1039/c1jm11766a · Cited by 288
Control of the functionality of graphene oxide for its application in epoxy nanocomposites
Li, Z., Wang, R., Young, R. J., Deng, L., Yang, F., Hao, L., Jiao, W., & Liu, W. (2013) · Polymer · doi:10.1016/j.polymer.2013.09.054 · Cited by 287
Graphene Oxide−Polyelectrolyte Nanomembranes
Kulkarni, D. D., Choi, I., Singamaneni, S. S., & Tsukruk, V. V. (2010) · ACS Nano · doi:10.1021/nn101204d · Cited by 281
Green fabrication of chitosan films reinforced with parallel aligned graphene oxide
Pan, Y., Wu, T., Bao, H., & Li, L. (2011) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2010.10.054 · Cited by 277
Pavithra, C. L. P., Sarada, B. V., Rajulapati, K. V., Rao, T. N., & Sundararajan, G. (2014) · Scientific Reports · doi:10.1038/srep04049 · Cited by 277
Fang, M., Zhang, Z., Li, J., Zhang, H., Lu, H., & Yang, Y. (2010) · Journal of Materials Chemistry · doi:10.1039/c0jm01620a · Cited by 275
Yousefi, N., Lin, X., Zheng, Q., Shen, X., Pothnis, J. R., Jia, J., Zussman, E., & Kim, J.-K. (2013) · Carbon · doi:10.1016/j.carbon.2013.03.034 · Cited by 272
Wan, Y.-J., Zhu, P.-L., Yu, S.-H., Sun, R., Wong, C.-P., & Liao, W.-H. (2017) · Carbon · doi:10.1016/j.carbon.2017.01.054 · Cited by 267
Graphene-Based Nanocomposites: Synthesis, Mechanical Properties, and Characterizations
Ibrahim, A., Klopocinska, A., Horvat, K., & Abdel Hamid, Z. (2021) · Polymers · doi:10.3390/polym13172869 · Cited by 265
Zhan, Y., Wu, J., Xia, H., Yan, N., Fei, G., & Yuan, G. (2011) · Macromolecular Materials and Engineering · doi:10.1002/mame.201000358 · Cited by 261
A tough graphene nanosheet/hydroxyapatite composite with improved in vitro biocompatibility
Zhang, L., Liu, W., Yue, C., Zhang, T., Li, P., Xing, Z., & Chen, Y. (2013) · Carbon · doi:10.1016/j.carbon.2013.04.074 · Cited by 260
Wang, F., Drzal, L. T., Qin, Y., & Huang, Z. (2016) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2016.04.009 · Cited by 256
Lu, H., Yao, Y., Huang, W. M., & Hui, D. (2014) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2014.07.022 · Cited by 114
Lu, H., Liang, F., Gou, J., Leng, J., & Du, S. (2014) · Smart Materials and Structures · doi:10.1088/0964-1726/23/8/085034 · Cited by 55
Moqbel, R. A., Gondal, M. A., Qahtan, T. F., & Dastageer, M. A. (2018) · Materials Research Express · doi:10.1088/2053-1591/aab6ec · Cited by 23
Metadata
- Authors
- Reif, J., Rafiee, J., Wang, Z., Song, H., Yu, Z.-Z., & Koratkar, N.
- Venue
- ACS Nano
- Publisher
- American Chemical Society (ACS)
- Published
- 2009-12-03
- Volume
- 3
- Issue
- 12
- Pages
- 3884-3890
- ISSN
- 1936-0851 (ISSN-L)
- 1936-086X
- OpenAlex
- W2000105557
- Cited by
- 2,890
- References
- 2
- FWCI
- 31.42
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.