CoChat
Sign Up
Cited by 162Geological and Geochemical AnalysisGeological and Geophysical StudiesGeological and Tectonic Studies in Latin America

The steady state thermal structure of eroding orogenic belts and accretionary prisms

Royden, Leigh H.·1993·Journal of Geophysical Research: Solid Earth
DOI 10.1029/92jb01954
Open this paper in CoChat — free account

Abstract

An analytical expression, derived in this paper, for the steady state thermal structure of thrust belts and subduction systems shows that surface erosion rate, basal accretion rate, and upper plate heat production are extremely important in controlling the temperature and metamorphic history of orogenic belts and accretionary prisms, especially where upper plate thickness ( h ) is large. For example, even at rapid erosion and accretion rates and with large upper plate heat productions, temperatures near the toe of a thrust wedge (e.g. at h =5 km) are nearly the same as those that would be present in the absence of erosion, accretion and upper plate heat production; in thicker parts of the same wedge (e.g. at h =30 km) the combined effects of erosion, accretion and upper plate heat production can be dramatic. For sufficiently large magnitudes of upper plate heat production or sufficiently rapid erosion rates inverted (negative) geothermal gradients are produced in the lower part of the upper plate and the upper part of the lower plate, although it is difficult to produce inverted geotherms where h ≤20 km. The potential importance of erosion and accretion can be illustrated through two examples: (1) beneath the Himalayas, increasing the upper plate radiogenic heat production from 0 to 2.5 mW/m 3 and increasing the rate of surface erosion from 0 to 1 mm/yr raises the computed steady state temperatures on the Main Central Thrust, at h = 30 km, from 265°C to 600°C, and produces a local temperature maximum of 635°C located 6 km above the fault; and (2) within the upper plate of the Peru trench, increasing the rate of surface erosion and basal accretion from 0 to 2.4 mm/yr (or increasing the upper plate radiogenic heat production from 0 to 1.3 mW/m 3 ) increases the computed steady state surface heat flow at h =30 km from 10 to 33 mW/m 3 , but only increases temperatures at the fault surface from 125°C to 170°C. Shear heating along thrust faults or subduction boundaries is not necessary to produce the high metamorphic temperatures or surface heat flows observed in these two examples, and the generation of large amounts of heat by shear stresses on the faults (more than a few tens of bars) appears to be inconsistent with some of the observations made in these areas. This study indicates that many of the major discrepancies between existing thermal models of overthrust belts and observed temperatures, as inferred from field data, can be attributed to neglect of horizontal and vertical advection of heat caused by surface erosion and by accretion of material from lower plate to upper plate across the fault surface.

Integrity signals

Registry

Crossref · 10.1029/92jb01954

Cites

36 of 36 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

  • The HP belt was incorporated into the orogen by basal accretion to the orogenic wedge.

    “This resulted in incorporation of the HP belt into the orogen, a process that has been termed basal accretion to the orogenic wedge (e.g., Dahlen and Barr 1989; Royden 1993).”

    From The High Pressure belt in the Grenville Province: architecture, timing, and exhumation (2002) · cites this paper as Royden 1993

Cites

Flagged first, then by citations

1 of the 37 references couldn’t be matched to a known paper.

Cited by

Sorted by citations

Related

Authors
Royden, L. H.
Corresponding author
Royden, Leigh H.
ORCID
Royden, Leigh H.
Venue
Journal of Geophysical Research: Solid Earth
Publisher
American Geophysical Union (AGU)
Published
1993-03-10
Volume
98
Issue
B3
Pages
4487-4507
ISSN
0148-0227 (ISSN-L)
DOI
10.1029/92jb01954
OpenAlex
W2009145927
Cited by
162
References
37
Citations by year
2026: 2 · 2025: 2 · 2024: 1 · 2023: 5 · 2022: 1 · 2021: 4 · 2020: 3 · 2019: 3 · 2018: 3 · 2017: 9 · 2016: 5 · 2015: 8 · 2014: 7 · 2013: 9 · 2012: 4
FWCI
6.41
Type
journal article
Language
en
Open access
closed
Licence
onlinelibrary.wiley.com/termsAndConditions#vor (vor, 7134 d)
Locations
Journal of Geophysical Research Atmospheres (publishedVersion)
Topics
  • Physical Sciences › Earth and Planetary Sciences › Geophysics › Geological and Geochemical Analysis
  • Physical Sciences › Earth and Planetary Sciences › Geology › Geological and Geophysical Studies
  • Physical Sciences › Earth and Planetary Sciences › Geophysics › Geological and Tectonic Studies in Latin America
Keywords
orogenic belts, accretionary prism, fold and thrust belt, subduction zone, surface erosion rate, radiogenic heat production, geothermal gradient, metamorphic temperature, surface heat flow, Himalaya, Main Central Thrust, shear heating, thermal modeling

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review