CoChat

Controls on trench topography from dynamic models of subducted slabs

Open access
Zhong, Shijie, Gurnis, Michael · 1994 · Journal of Geophysical Research: Solid Earth
Cited by 157

The DOI matches its Crossref record; 3 of the 3 references it cites were found in a registry or an index.

Abstract

A finite element method with constrained elements and Lagrange multipliers is used to study tectonic faults in a viscous medium. A fault, representing the interface between overriding and subducting plates, has been incorporated into a viscous flow model of a subduction zone in which both thermal buoyancy and the buoyancy associated with the phase change from olivine to spinel are included. The fault causes stress to concentrate in its vicinity, giving rise to a weak plate margin and a mobile plate if a power law rheology is used. Surface dynamic topography with either a Newtonian or a power law rheology and with typical subduction zone parameters is characterized by a narrow and deep trench and a broadly depressed back arc basin. This suggests that oceanic trenches and back arc basins over subduction zones are dynamically compensated by viscous flow. Our models show that trench depth increases with fault dip angle, slab dip angle, slab length, and age of oceanic lithosphere just prior to subduction. The influence of fault dip angle and age of lithosphere on trench depth is greater than the influence of slab dip angle and slab length. These relationships of trench depth versus subduction zone parameters explain well the statistics of observed trench depths. For those subduction zones with oceanic lithosphere on both sides of the trench, observed trench depths have been corrected for fault and slab dip angles, based on the relationships from the dynamic models. After correction to a common set of parameters, trench depth correlates linearly with age of lithosphere prior to subduction with a slope which is close to what models having high viscosities within the transition zone and lower mantle predict. Comparison between the trench depths, corrected for fault and slab dip angles, and model trench depths suggests that the resisting tangential stress on faults in subduction zones may range from 15 MPa to 30 MPa, depending on model details.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1029/94jb00809

Cites

3 of 3 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 3 references

Cited by

Metadata

Authors
Zhong, S., & Gurnis, M.
Venue
Journal of Geophysical Research: Solid Earth
Published
1994-08-10
Volume
99
Issue
B8
Pages
15683-15695
ISSN
0148-0227 (ISSN-L)
OpenAlex
W1977196609
Cited by
157
References
3
FWCI
5.32
Type
journal article
Language
en
Open access
bronze

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.