The DOI matches its Crossref record; 27 of the 27 references it cites were found in a registry or an index.
Synergistic toughening of composite fibres by self-alignment of reduced graphene oxide and carbon nanotubes
Open accessAbstract
The extraordinary properties of graphene and carbon nanotubes motivate the development of methods for their use in producing continuous, strong, tough fibres. Previous work has shown that the toughness of the carbon nanotube-reinforced polymer fibres exceeds that of previously known materials. Here we show that further increased toughness results from combining carbon nanotubes and reduced graphene oxide flakes in solution-spun polymer fibres. The gravimetric toughness approaches 1,000 J g−1, far exceeding spider dragline silk (165 J g−1) and Kevlar (78 J g−1). This toughness enhancement is consistent with the observed formation of an interconnected network of partially aligned reduced graphene oxide flakes and carbon nanotubes during solution spinning, which act to deflect cracks and allow energy-consuming polymer deformation. Toughness is sensitive to the volume ratio of the reduced graphene oxide flakes to the carbon nanotubes in the spinning solution and the degree of graphene oxidation. The hybrid fibres were sewable and weavable, and could be shaped into high-modulus helical springs. Composite fibres made of polymers reinforced by carbon nanotubes are known for their exceptional toughness. Shinet al. make these composites even tougher, by self-aligning carbon nanotubes and reduced graphene oxide flakes within the polymer matrix.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Synthesis of graphene-based nanosheets via chemical reduction of exfoliated graphite oxide
Stankovich, S., Dikin, D. A., Piner, R. D., Kohlhaas, K. A., Kleinhammes, A., Jia, Y., Wu, Y., Nguyen, S. T., & Ruoff, R. S. (2007) · Carbon · doi:10.1016/j.carbon.2007.02.034 · Cited by 13,878
Graphene-based composite materials
Stankovich, S., Dikin, D. A., Dommett, G. H. B., Kohlhaas, K. M., Zimney, E. J., Stach, E. A., Piner, R. D., Nguyen, S. T., & Ruoff, R. S. (2006) · Nature · doi:10.1038/nature04969 · Cited by 12,922
Tuinstra, F., & Koenig, J. L. (1970) · The Journal of Chemical Physics · doi:10.1063/1.1674108 · Cited by 10,717
Processable aqueous dispersions of graphene nanosheets
Li, D., Müller, M. B., Gilje, S., Kaner, R. B., & Wallace, G. G. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2007.451 · Cited by 9,114
Self-citationFunctionalized graphene sheets for polymer nanocomposites
Ramanathan, T., Abdala, A. A., Stankovich, S., Dikin, D. A., Herrera-Alonso, M., Piner, R. D., Adamson, D. H., Schniepp, H. C., Chen, X., Ruoff, R. S., et al. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2008.96 · Cited by 3,470
Yang, D., Velamakanni, A., Bozoklu, G., Park, S., Stoller, M., Piner, R. D., Stankovich, S., Jung, I., Field, D. A., Ventrice, C. A., et al. (2009) · Carbon · doi:10.1016/j.carbon.2008.09.045 · Cited by 3,260
Mechanically Strong, Electrically Conductive, and Biocompatible Graphene Paper
Chen, H., Müller, M. B., Gilmore, K. J., Wallace, G. G., & Li, D. (2008) · Advanced Materials · doi:10.1002/adma.200800757 · Cited by 2,040
Self-citationMacroscopic Fibers and Ribbons of Oriented Carbon Nanotubes
Vigolo, B., Pénicaud, A., Coulon, C., Sauder, C., Pailler, R., Journet, C., Bernier, P., & Poulin, P. (2000) · Science · doi:10.1126/science.290.5495.1331 · Cited by 1,851
Measurement of the quantum capacitance of graphene
Xia, J., Chen, F., Li, J., & Tao, N. (2009) · Nature Nanotechnology · doi:10.1038/nnano.2009.177 · Cited by 1,752
Liquid crystalline spinning of spider silk
Vollrath, F., & Knight, D. P. (2001) · Nature · doi:10.1038/35069000 · Cited by 1,610
Cited by
The mechanics of graphene nanocomposites: A review
Young, R. J., Kinloch, I. A., Gong, L., & Novoselov, K. S. (2012) · Composites Science and Technology · doi:10.1016/j.compscitech.2012.05.005 · Cited by 1,294
Graphene: An Emerging Electronic Material
Weiss, N. O., Zhou, H., Liao, L., Liu, Y., Jiang, S., Huang, Y., & Duan, X. (2012) · Advanced Materials · doi:10.1002/adma.201201482 · Cited by 897
Two‐Dimensional Nanomaterials for Biomedical Applications: Emerging Trends and Future Prospects
Chimene, D., Alge, D. L., & Gaharwar, A. K. (2015) · Advanced Materials · doi:10.1002/adma.201502422 · Cited by 880
Highly thermally conductive and mechanically strong graphene fibers
Xin, G., Yao, T., Sun, H., Scott, S. M., Shao, D., Wang, G., & Lian, J. (2015) · Science · doi:10.1126/science.aaa6502 · Cited by 740
Graphene-based materials for tissue engineering
Shin, S. R., Li, Y.-C., Jang, H. L., Khoshakhlagh, P., Akbari, M., Nasajpour, A., Zhang, Y. S., Tamayol, A., & Khademhosseini, A. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.03.007 · Cited by 721
Carbon Nanotubes and Graphene for Flexible Electrochemical Energy Storage: from Materials to Devices
Wen, L., Li, F., & Cheng, H. (2016) · Advanced Materials · doi:10.1002/adma.201504225 · Cited by 711
Ultrastrong Fibers Assembled from Giant Graphene Oxide Sheets
Xu, Z., Sun, H., Zhao, X., & Gao, C. (2013) · Advanced Materials · doi:10.1002/adma.201203448 · Cited by 699
Chatterjee, S., Nafezarefi, F., Tai, N. H., Schlagenhauf, L., Nüesch, F. A., & Chu, B. T. T. (2012) · Carbon · doi:10.1016/j.carbon.2012.07.021 · Cited by 659
Superstructured Assembly of Nanocarbons: Fullerenes, Nanotubes, and Graphene
Li, Z., Liu, Z., Sun, H., & Gao, C. (2015) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00102 · Cited by 554
Zhang, J., Xu, Z., Mai, W., Min, C., Zhou, B., Shan, M., Li, Y., Yang, C., Wang, Z., & Qian, X. (2013) · Journal of Materials Chemistry A · doi:10.1039/c2ta01415g · Cited by 537
Energy harvesting and storage in 1D devices
Sun, H., Zhang, Y., Zhang, J., Sun, X., & Peng, H. (2017) · Nature Reviews Materials · doi:10.1038/natrevmats.2017.23 · Cited by 528
Cheng, C., Li, S., Thomas, A., Kotov, N. A., & Haag, R. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00520 · Cited by 527
Graphene-based wearable piezoresistive physical sensors
Zheng, Q., Lee, J.-H., Shen, X., Chen, X., & Kim, J.-K. (2020) · Materials Today · doi:10.1016/j.mattod.2019.12.004 · Cited by 486
Self-citationGraphene-based macroscopic assemblies and architectures: an emerging material system
Cong, H.-P., Chen, J.-F., & Yu, S.-H. (2014) · Chem. Soc. Rev. · doi:10.1039/c4cs00181h · Cited by 461
Jalili, R., Aboutalebi, S. H., Esrafilzadeh, D., Shepherd, R. L., Chen, J., Aminorroaya‐Yamini, S., Konstantinov, K., Minett, A. I., Razal, J. M., & Wallace, G. G. (2013) · Advanced Functional Materials · doi:10.1002/adfm.201300765 · Cited by 431
Self-citationTowards High‐Performance Bioinspired Composites
Studart, A. R. (2012) · Advanced Materials · doi:10.1002/adma.201201471 · Cited by 429
Graphene fiber: a new trend in carbon fibers
Xu, Z., & Gao, C. (2015) · Materials Today · doi:10.1016/j.mattod.2015.06.009 · Cited by 375
Su, D., Cortie, M., & Wang, G. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201602014 · Cited by 360
Review of functionalization, structure and properties of graphene/polymer composite fibers
Ji, X., Xu, Y., Zhang, W., Cui, L., & Liu, J. (2016) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2016.04.011 · Cited by 351
Graphene and graphene derivatives toughening polymers: Toward high toughness and strength
Wang, J., Jin, X., Li, C., Wang, W., Wu, H., & Guo, S. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.03.229 · Cited by 333
Cheng, H., Dong, Z., Hu, C., Zhao, Y., Hu, Y., Qu, L., Chen, N., & Dai, L. (2013) · Nanoscale · doi:10.1039/c3nr00320e · Cited by 332
A Review on Graphene Fibers: Expectations, Advances, and Prospects
Fang, B., Chang, D., Xu, Z., & Gao, C. (2020) · Advanced Materials · doi:10.1002/adma.201902664 · Cited by 332
Paul, R., Du, F., Dai, L., Ding, Y., Wang, Z. L., Wei, F., & Roy, A. (2019) · Advanced Materials · doi:10.1002/adma.201805598 · Cited by 313
Graphene‐Based Fibers: A Review
Meng, F., Lu, W., Li, Q., Byun, J., Oh, Y., & Chou, T. (2015) · Advanced Materials · doi:10.1002/adma.201501126 · Cited by 294
High strength in combination with high toughness in robust and sustainable polymeric materials
Liao, X., Dulle, M., de Souza e Silva, J. M., Wehrspohn, R. B., Agarwal, S., Förster, S., Hou, H., Smith, P., & Greiner, A. (2019) · Science · doi:10.1126/science.aay9033 · Cited by 286
Graphene-based artificial nacre nanocomposites
Zhang, Y., Gong, S., Zhang, Q., Ming, P., Wan, S., Peng, J., Jiang, L., & Cheng, Q. (2016) · Chemical Society Reviews · doi:10.1039/c5cs00258c · Cited by 278
Recent Advances in Fabrication and Characterization of Graphene-Polymer Nanocomposites
Galpaya, D., Wang, M., Liu, M., Motta, N., Waclawik, E., & Yan, C. (2012) · Graphene · doi:10.4236/graphene.2012.12005 · Cited by 262
Synergistic reinforcing effect from graphene and carbon nanotubes
Liang, X., & Cheng, Q. (2018) · Composites Communications · doi:10.1016/j.coco.2018.09.002 · Cited by 85
Metadata
- Authors
- Shin, M. K., Lee, B., Kim, S. H., Lee, J. A., Spinks, G. M., Gambhir, S., Wallace, G. G., Kozlov, M. E., Baughman, R. H., & Kim, S. J.
- Venue
- Nature Communications
- Published
- 2012-01-31
- Volume
- 3
- Issue
- 1
- Pages
- 650-650
- ISSN
- 2041-1723 (ISSN-L)
- OpenAlex
- W2058285177
- Cited by
- 423
- References
- 27
- FWCI
- 15.64
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.