The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Size effect, critical resolved shear stress, stacking fault energy, and solid solution strengthening in the CrMnFeCoNi high-entropy alloy
Open accessAbstract
High-entropy alloys (HEAs) comprise a novel class of scientifically and technologically interesting materials. Among these, equatomic CrMnFeCoNi with the face-centered cubic (FCC) structure is noteworthy because its ductility and strength increase with decreasing temperature while maintaining outstanding fracture toughness at cryogenic temperatures. Here we report for the first time by single-crystal micropillar compression that its bulk room temperature critical resolved shear stress (CRSS) is ~33–43 MPa, ~10 times higher than that of pure nickel. CRSS depends on pillar size with an inverse power-law scaling exponent of –0.63 independent of orientation. Planar ½ < 110 > {111} dislocations dissociate into Shockley partials whose separations range from ~3.5–4.5 nm near the screw orientation to ~5–8 nm near the edge, yielding a stacking fault energy of 30 ± 5 mJ/m 2. Dislocations are smoothly curved without any preferred line orientation indicating no significant anisotropy in mobilities of edge and screw segments. The shear-modulus-normalized CRSS of the HEA is not exceptionally high compared to those of certain concentrated binary FCC solid solutions. Its rough magnitude calculated using the Fleischer/Labusch models corresponds to that of a hypothetical binary with the elastic constants of our HEA, solute concentrations of 20–50 at.%, and atomic size misfit of ~4%.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Yeh, J. ‐., Chen, S. ‐., Lin, S. ‐., Gan, J. ‐., Chin, T. ‐., Shun, T. ‐., Tsau, C. ‐., & Chang, S. ‐. (2004) · Advanced Engineering Materials · doi:10.1002/adem.200300567 · Cited by 15,281
Microstructural development in equiatomic multicomponent alloys
Cantor, B., Chang, I. T. H., Knight, P., & Vincent, A. J. B. (2004) · Materials Science and Engineering: A · doi:10.1016/j.msea.2003.10.257 · Cited by 10,130
A fracture-resistant high-entropy alloy for cryogenic applications
Gludovatz, B., Hohenwarter, A., Catoor, D., Chang, E. H., George, E. P., & Ritchie, R. O. (2014) · Science · doi:10.1126/science.1254581 · Cited by 5,714
Self-citationOtto, F., Dlouhý, A., Somsen, C., Bei, H., Eggeler, G., & George, E. P. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.06.018 · Cited by 3,352
Self-citationSample Dimensions Influence Strength and Crystal Plasticity
Uchic, M. D., Dimiduk, D. M., Florando, J. N., & Nix, W. D. (2004) · Science · doi:10.1126/science.1098993 · Cited by 2,330
Plasticity in small-sized metallic systems: Intrinsic versus extrinsic size effect
Greer, J. R., & De Hosson, J. T. M. (2011) · Progress in Materials Science · doi:10.1016/j.pmatsci.2011.01.005 · Cited by 1,763
Dislocations and Cracks in Anisotropic Elasticity
Stroh, A. N. (1958) · Philosophical Magazine · doi:10.1080/14786435808565804 · Cited by 1,606
Greer, J. R., Oliver, W. C., & Nix, W. D. (2005) · Acta Materialia · doi:10.1016/j.actamat.2004.12.031 · Cited by 1,501
Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys
Otto, F., Yang, Y., Bei, H., & George, E. P. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.01.042 · Cited by 1,445
Self-citationA Statistical Theory of Solid Solution Hardening
Labusch, R. (1970) · physica status solidi (b) · doi:10.1002/pssb.19700410221 · Cited by 1,439
Schuh, B., Mendez-Martin, F., Völker, B., George, E. P., Clemens, H., Pippan, R., & Hohenwarter, A. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.025 · Cited by 1,323
Self-citationSubstitutional solution hardening
Fleischer, R. L. (1963) · Acta Metallurgica · doi:10.1016/0001-6160(63)90213-x · Cited by 1,281
Tensile properties of high- and medium-entropy alloys
Gali, A., & George, E. P. (2013) · Intermetallics · doi:10.1016/j.intermet.2013.03.018 · Cited by 1,194
Self-citationOtto, F., Dlouhý, A., Pradeep, K. G., Kuběnová, M., Raabe, D., Eggeler, G., & George, E. P. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.04.005 · Cited by 932
Self-citationNanoscale gold pillars strengthened through dislocation starvation
Greer, J. R., & Nix, W. D. (2006) · Physical Review B · doi:10.1103/physrevb.73.245410 · Cited by 925
Strengthening Mechanisms in Crystal Plasticity
Argon, A. (2007) · Oxford University Press eBooks · doi:10.1093/acprof:oso/9780198516002.001.0001 · Cited by 920
Mechanical Properties and Stacking Fault Energies of NiFeCrCoMn High-Entropy Alloy
Zaddach, A. J., Niu, C., Koch, C. C., & Irving, D. L. (2013) · JOM · doi:10.1007/s11837-013-0771-4 · Cited by 878
Plasticity of Micrometer-Scale Single Crystals in Compression
Uchic, M. D., Shade, P. A., & Dimiduk, D. M. (2009) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-082908-145422 · Cited by 770
Size-affected single-slip behavior of pure nickel microcrystals
Dimiduk, D. M., Uchic, M. D., & Parthasarathy, T. A. (2005) · Acta Materialia · doi:10.1016/j.actamat.2005.05.023 · Cited by 717
Scale-Free Intermittent Flow in Crystal Plasticity
Dimiduk, D. M., Woodward, C., LeSar, R., & Uchic, M. D. (2006) · Science · doi:10.1126/science.1123889 · Cited by 587
Precipitation in the equiatomic high-entropy alloy CrMnFeCoNi
Pickering, E. J., Muñoz-Moreno, R., Stone, H. J., & Jones, N. G. (2016) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.10.025 · Cited by 555
Microstructure and texture evolution during annealing of equiatomic CoCrFeMnNi high-entropy alloy
Bhattacharjee, P. P., Sathiaraj, G. D., Zaid, M., Gatti, J. R., Lee, C., Tsai, C.-W., & Yeh, J.-W. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.10.237 · Cited by 530
Laplanche, G., Gadaud, P., Horst, O., Otto, F., Eggeler, G., & George, E. P. (2015) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.11.061 · Cited by 467
Self-citationEffect of cryo-deformation on structure and properties of CoCrFeNiMn high-entropy alloy
Stepanov, N., Tikhonovsky, M., Yurchenko, N., Zyabkin, D., Klimova, M., Zherebtsov, S., Efimov, A., & Salishchev, G. (2015) · Intermetallics · doi:10.1016/j.intermet.2014.12.004 · Cited by 399
Alers, G. A., Neighbours, J. R., & Sato, H. (1960) · Journal of Physics and Chemistry of Solids · doi:10.1016/0022-3697(60)90125-6 · Cited by 371
Direct measurements of stacking-fault energies from observations of dislocation nodes
Howie, A., & Swann, P. R. (1961) · Philosophical magazine · doi:10.1080/14786436108243372 · Cited by 357
Fundamental Differences in Mechanical Behavior between Two Types of Crystals at the Nanoscale
Brinckmann, S., Kim, J.-Y., & Greer, J. R. (2008) · Physical Review Letters · doi:10.1103/physrevlett.100.155502 · Cited by 342
Plastic deformation of nickel single crystals at low temperatures
Haasen, P. (1958) · Philosophical magazine · doi:10.1080/14786435808236826 · Cited by 334
Otto, F., Hanold, N. L., & George, E. P. (2014) · Intermetallics · doi:10.1016/j.intermet.2014.05.014 · Cited by 322
Self-citationCorrelation between Critical Temperature and Strength of Small-Scale bcc Pillars
Schneider, A. S., Kaufmann, D., Clark, B. G., Frick, C. P., Gruber, P. A., Mönig, R., Kraft, O., & Arzt, E. (2009) · Physical Review Letters · doi:10.1103/physrevlett.103.105501 · Cited by 258
Atomic-scale characterization and modeling of 60° dislocations in a high-entropy alloy
Smith, T. M., Hooshmand, M. S., Esser, B. D., Otto, F., McComb, D. W., George, E. P., Ghazisaeidi, M., & Mills, M. J. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.03.045 · Cited by 226
Self-citationDetermination of Mechanical Properties of Copper at the Micron Scale
Kiener, D., Motz, C., Schöberl, T., Jenko, M., & Dehm, G. (2006) · Advanced Engineering Materials · doi:10.1002/adem.200600129 · Cited by 224
Microstructure versus Size: Mechanical Properties of Electroplated Single Crystalline Cu Nanopillars
Jennings, A. T., Burek, M. J., & Greer, J. R. (2010) · Physical Review Letters · doi:10.1103/physrevlett.104.135503 · Cited by 212
Polycrystalline elastic moduli of a high-entropy alloy at cryogenic temperatures
Haglund, A., Koehler, M., Catoor, D., George, E. P., & Keppens, V. (2015) · Intermetallics · doi:10.1016/j.intermet.2014.11.005 · Cited by 196
Self-citationSlip nucleation in single crystal FeNiCoCrMn high entropy alloy
Patriarca, L., Ojha, A., Şehitoğlu, H., & Chumlyakov, Y. I. (2015) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.09.009 · Cited by 155
Cited by
George, E. P., Raabe, D., & Ritchie, R. O. (2019) · Nature Reviews Materials · doi:10.1038/s41578-019-0121-4 · Cited by 5,047
Self-citationHigh entropy alloys: A focused review of mechanical properties and deformation mechanisms
George, E. P., Curtin, W. A., & Tasan, C. C. (2020) · Acta Materialia · doi:10.1016/j.actamat.2019.12.015 · Cited by 1,917
Self-citationTuning element distribution, structure and properties by composition in high-entropy alloys
Ding, Q., Zhang, Y., Chen, X., Fu, X., Chen, D., Chen, S., Gu, L., Wei, F., Bei, H., Gao, Y., et al. (2019) · Nature · doi:10.1038/s41586-019-1617-1 · Cited by 1,614
Short-range order and its impact on the CrCoNi medium-entropy alloy
Zhang, R., Zhao, S., Ding, J., Chong, Y., Jia, T., Ophus, C., Asta, M., Ritchie, R. O., & Minor, A. M. (2020) · Nature · doi:10.1038/s41586-020-2275-z · Cited by 1,279
Clarifying the four core effects of high-entropy materials
Hsu, W.-L., Tsai, C.-W., Yeh, A.-C., & Yeh, J.-W. (2024) · Nature Reviews Chemistry · doi:10.1038/s41570-024-00602-5 · Cited by 928
Metadata
- Authors
- Okamoto, N. L., Fujimoto, S., Kambara, Y., Kawamura, M., Chen, Z. M. T., Matsunoshita, H., Tanaka, K., Inui, H., & George, E. P.
- Venue
- Scientific Reports
- Published
- 2016-10-24
- Volume
- 6
- Issue
- 1
- Pages
- 35863-35863
- ISSN
- 2045-2322 (ISSN-L)
- OpenAlex
- W2539140484
- Cited by
- 446
- References
- 35
- FWCI
- 28.04
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.