Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer
Open accessThe DOI matches its Crossref record; 46 of the 46 references it cites were found in a registry or an index; 1 of the 27 sources its claims cite were checked for support.
Abstract
The PLLA/PCL multi-block copolymer was introduced into the stereocomplexed PLA matrix, and its effect on the crystallization, thermal and mechanical properties of the stereocomplexed PLA was discussed.
Overview
CoChat Summary
TL;DR
Flexible PLLA/PCL multiblock copolymers were synthesized and blended with PLLA/PDLA to promote stereocomplexation and toughen sc-PLA. The blends achieved full stereocomplexation during melting crystallization and showed greatly improved elongation at break, with only modest tensile-strength loss.
Key findings
- PLLA/PCL multiblock copolymers were successfully synthesized via UPy quadruple hydrogen bonding; GPC molecular weights were 28.3, 39.8, and 40.4 kg mol⁻¹ for MBC0.9, MBC3.0, and MBC5.0, respectively.
- Introducing MBC promoted stereocomplexation during melting crystallization: DSC cooling curves showed only stereocomplex crystallization/melting when MBC was present, whereas sc-PLA alone showed stereocomplex crystallization at 125.2 °C and a weaker hc-crystal melting peak at 167.3 °C.
- Mechanical properties improved markedly: sc-PLA had tensile strength 69.5 MPa and elongation at break 16.4%; at >15% MBC, the blend showed 39.3 MPa and 189% elongation. The authors recommend 10–15% MBC to balance strength and toughness.
- Thermal stability decreased with MBC: higher MBC contents (10–20 wt%) shifted T5% lower by around 10 °C, and maximum degradation temperature shifted to 270–273 °C; increasing PLLA block length in MBC increased T5% and Td.
Methods
- PLLA/PCL multiblock copolymers were synthesized from a dihydroxyl-functionalized PCL macroinitiator by ring-opening polymerization of L-lactide to form PLLA-b-PCL-b-PLLA triblocks, followed by coupling with UPy-NCO. Products were characterized by ¹H NMR, GPC, DSC, WAXD, TGA, and POM.
- sc-PLA/MBC blends were prepared by solution casting from chloroform using equal weights of PLLA and PDLA plus MBC. MBC3.0 contents were 0%, 5%, 10%, 15%, and 20%; blends with different MBCX were tested at 15% MBC.
- Tensile tests used rectangular specimens of 30 × 3 × 0.1 mm³ at a crosshead speed of 20 mm min⁻¹; each sample was tested six times to calculate average value and deviation.
Limitations
- The paper does not state explicit limitations.
- Evident from the text: all sc-PLA/MBC blends were prepared by solution casting, so the results may not directly translate to melt-processed products; the paper notes sc-PLA’s weak melt memory and melt-processing challenges generally.
- Mechanical characterization is limited to room-temperature tensile tests on solution-cast films; no impact, flexural, or long-term degradation data are reported. The authors also note a trade-off in which increasing MBC lowers tensile strength, recommending only 10–15% MBC.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures









Verification
Claims the paper makes
1 Valid · 0 Not valid · 17 Not checked · 75 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It is clear that in Fig. 3(b), the multi-block copolymer based on PLLA-b-PCL-b-PLLA triblock copolymer shows a similar curve to the corresponding PLLA-b-PCL-b-PLLA triblock copolymer.”
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Results and discussion > Crystallization behavior, crystal structure and thermal stability of PLLA/PCL multiblock copolymers
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It is clearly observed from Fig. 9(a) that the tensile strength and elongation at break are significantly influenced by the MBC content.”
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Results and discussion > Mechanical properties
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“GPC result also found that the molecular weight of PLLA/PCL multiblock copolymer is larger than that of the corresponding PLLA-b-PCL-b-PLLA triblock copolymer (Fig. 2(b))”
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Results and discussion > Synthesis and characterization of PLLA/PCL multi block copolymers
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The number-averaged molecular weight (Mn,NMR) calculated by 1H NMR is 11.1 kg mol−1.”
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Results and discussion > Synthesis and characterization of PLLA/PCL multi block copolymers
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The results indicated that PLLA/PCL multi-block copolymers with controllable structure and composition were successfully synthesized.”
- Also stated in: § Synthesis and characterization of PLLA/PCL multi block copolymers · hedged
“These results indicate that the PLLA/PCL multiblock copolymer based on PLLA-b-PCL-b-PLLA triblock copolymer are successfully synthesized.”
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Abstract
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Synthesis and characterization of PLLA/PCL multi block copolymers · hedged
53 more claims
Create a free account to see all 93 claims and every source verdict.
- Probably not a substantial claim. 5
- It may state two separate claims as one. 30
- The quote only partly states this claim. 3
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Results and discussion > Synthesis and characterization of PLLA/PCL multi block copolymers
“And PLLA-b-PCL-b-PLLA triblock copolymer presents a low polydispersity index (<1.23).”
§ Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer† > Experimental section > Synthesis of PLLA/PCL multiblock copolymers
“| TBC3.0 | 2 : 4 | 3.0–11.1–3.0 | 17.1 | 19.1 | 1.23 | 35.1 | 86.9 |”
Citations
Cites
Folmer, B. J. B., Sijbesma, R. P., Versteegen, R. M., van der Rijt, J. A. J., & Meijer, E. W. (2000) · Advanced Materials · doi:10.1002/1521-4095(200006)12:12<874::aid-adma874>3.0.co;2-c · Cited by 696
Deng, S., Bai, H., Liu, Z., Zhang, Q., & Fu, Q. (2019) · Macromolecules · doi:10.1021/acs.macromol.8b02626 · Cited by 142
Evidence of a dual network/spherulitic crystalline morphology in PLA stereocomplexes
Saeidlou, S., Huneault, M. A., Li, H., Sammut, P., & Park, C. B. (2012) · Polymer · doi:10.1016/j.polymer.2012.10.030 · Cited by 120
Sustainable Poly(lactide-b-butadiene) Multiblock Copolymers with Enhanced Mechanical Properties
Lee, I., Panthani, T. R., & Bates, F. S. (2013) · Macromolecules · doi:10.1021/ma401508b · Cited by 117
Zhou, X., Deng, J., Fang, C., Lei, W., Song, Y., Zhang, Z., Huang, Z., & Li, Y. (2021) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2020.04.038 · Cited by 103
Self-citationPalai, B., Mohanty, S., & Nayak, S. K. (2020) · Polymer Testing · doi:10.1016/j.polymertesting.2019.106130 · Cited by 96
Tsuji, H., Wada, T., Sakamoto, Y., & Sugiura, Y. (2010) · Polymer · doi:10.1016/j.polymer.2010.08.010 · Cited by 87
Purnama, P., Jung, Y., & Kim, S. H. (2012) · Macromolecules · doi:10.1021/ma202814c · Cited by 80
Moradi, S., & Yeganeh, J. K. (2020) · Polymer Testing · doi:10.1016/j.polymertesting.2020.106735 · Cited by 75
Chang, R., Huang, Y., Shan, G., Bao, Y., Yun, X., Dong, T., & Pan, P. (2015) · Polymer Chemistry · doi:10.1039/c5py00742a · Cited by 72
Research works printed but not linked: 4
- Lv, 2021, Polymer, 222, 123648, 10.1016/j.polymer.2021.123648 · DOI · Paper page
- Bao, 2020, Polymer, 190, 122189, 10.1016/j.polymer.2020.122189 · DOI · Paper page
- Navarro-Baena, 2014, Polym. Degrad. Stab., 108, 140, 10.1016/j.polymdegradstab.2014.03.012 · DOI · Paper page
- Liu, 2014, Polym. Degrad. Stab., 101, 10, 10.1016/j.polymdegradstab.2014.01.023 · DOI · Paper page
Cited by
Poly(lactic acid) stereocomplexes based molecular architectures: Synthesis and crystallization
Michell, R. M., Ladelta, V., Da Silva, E., Müller, A. J., & Hadjichristidis, N. (2023) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2023.101742 · Cited by 77
A decade of innovation: Synthesis, properties and applications of PLA copolymers
Terzopoulou, Z. N., Zamboulis, A., Bikiaris, N. D., Xanthopoulou, E., Ioannidis, R. O., & Bikiaris, D. Ν. (2025) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2025.101991 · Cited by 68
Miao, X., Han, R., Tian, J., Ma, Y., Müller, A. J., & Li, Z. (2025) · Angewandte Chemie International Edition · doi:10.1002/anie.202417627 · Cited by 27
Ring-Opening Copolymerizations of a CO 2 -Derived δ-Valerolactone with ε-Caprolactone and l -Lactide
Anderson, R. J., Fine, R. L., Rapagnani, R. M., & Tonks, I. A. (2024) · Macromolecules · doi:10.1021/acs.macromol.4c00770 · Cited by 17
Neal, T. J., Neal, E. D., Cumby, J., & Garden, J. A. (2024) · Polymer Chemistry · doi:10.1039/d4py00169a · Cited by 12
Metadata
- Authors
- Jing, Z., Huang, X., Liu, X., Liao, M., Zhang, Z., & Li, Y.
- Affiliations
- Guangdong Ocean University (CN)
- Corresponding author
- Jing, Zhanxin
- Venue
- RSC Advances
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2022
- Volume
- 12
- Issue
- 21
- Pages
- 13180-13191
- ISSN
- 2046-2069 (ISSN-L)
- PMC
- PMC9063687
- OpenAlex
- W4229050456
- Cited by
- 23
- References
- 46
- Citations by year
- 2026: 5 · 2025: 6 · 2024: 7 · 2023: 4 · 2022: 1
- FWCI
- 1.04
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- RSC Advances (publishedVersion, cc-by-nc)
- PubMed Central (publishedVersion, cc-by-nc)
- PubMed (publishedVersion)
- Funders
- Natural Science Foundation of Guangdong Province (2018A030307020)
- Guangdong Ocean University (002029002012)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Keywords
- poly(L-lactic acid), polycaprolactone, multiblock copolymers, stereocomplexation, PLA blends, crystallization behavior, crystal structure, thermal stability, mechanical properties, toughness, nucleation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.