CoChat

Assessment of Machinability of Ti6Al4V Alloy Under Dry Conditions

Open access
Younas, Muhammad, Mohammed Sambo, Abdulkadir, Asim, Taimoor, Saharudin, Shahneel · 2024 · MATEC Web of Conferences

The DOI matches its Crossref record; 13 of the 13 references it cites were found in a registry or an index.

Abstract

Titanium alloys pose significant challenges during machining, necessitates a thorough investigation into the impact of process parameters on machining Ti6Al4V alloy. This study investigates into the machinability of Ti6Al4V alloy under dry machining conditions using uncoated tools. The experimental design studiedthe effect of process parameters on the cutting power, surface roughness and material removal rate during dry machining of Ti6Al4V alloy. Utilizing Taguchi design of experiments, unified cutting experiments were conducted under dry conditions employing uncoated tools. The study findings revealed that optimal cutting parameters lead to improved cutting energy consumption, reduced tool wear, and enhanced surface finish and material rates. Analysis of Variance (ANOVA) and regression modelling were employed to obtain an objective function capable of predicting the best cutting conditions. ANOVA showed that cutting speed is the main factor for an increase in the cutting power with major contribution of 73 % whereas feed rate is the key factor for surface roughness with the contribution of 80 %. These results help to gain the advantages of dry machining under optimal conditions, facilitating clean production with minimal energy consumption and improved surface quality.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1051/matecconf/202440106005

Cites

13 of 13 references verified0 citation errors · 0 not checkable

Statistics

Figures

Fig 1 Experimental setup for turning Ti6Al4V alloy.
Fig 1 Experimental setup for turning Ti6Al4V alloy.CC-BY · From the PDF
Fig 2 Cutting power against (a) MRR (b) speed and feed (c) surface plot
Fig 2 Cutting power against (a) MRR (b) speed and feed (c) surface plotCC-BY · From the PDF
Image 3
CC-BY · From the PDF
Image 4
CC-BY · From the PDF
Fig 3 Surface roughness plotted against speed and feed.
Fig 3 Surface roughness plotted against speed and feed.CC-BY · From the PDF
Image 6
CC-BY · From the PDF

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 13 references

Research works printed but not linked: 4

  1. 12. S. Pervaiz, I. Deiab, and C. Mihai Nicolescu, Energy Consumption and Surface Finish Analysis of Machining Ti6Al4V. [Online]. Available: https://www.researchgate.net/publication/266731984
  2. 15. M. Younas , Process Parameters and Its Effect on Surface Roughness During Turning Ti6Al4V Alloy, in Advances in Manufacturing Technology XXXIII: Proceedings of the 17th International Conference on Manufacturing Research, incorporating the 34th National Conference on Manufacturing Research, 10-12 September 2019, Queen's University, Belfast, (2019)
  3. 16. S. H. I. Jaffery, M. Younas, M. Khan, and L. Ali, Energy Consumption Analysis in Turning Ti-6Al-4V alloy, in 2020 IEEE 11th International Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT), (2020)
  4. 17. M. Khan, S. S. Warsi, S. H. I. Jaffery, R. Ahmad, and M. Younas, Analysis of Energy Consumption in Orthogonal Machining of Al 6061-T6 Alloy, in Advances in Manufacturing Technology XXXIII: Proceedings of the 17th International Conference on Manufacturing Research, incorporating the 34th National Conference on Manufacturing Research, 10-12 September 2019, Queen's University, Belfast (2019)

Cited by

Metadata

Authors
Younas, M., Mohammed Sambo, A., Asim, T., & Saharudin, S.
Affiliations
Robert Gordon University (GB)
Corresponding author
Younas, Muhammad
Venue
MATEC Web of Conferences
Publisher
EDP Sciences
Published
2024
Volume
401
Pages
06005
ISSN
2261-236X (ISSN-L)
OpenAlex
W4401926277
Cited by
2
References
12
Citations by year
2024: 2
FWCI
2.57
Type
conference paper
Language
en
Open access
Locations
  • MATEC Web of Conferences (publishedVersion, cc-by)
  • Open Access Institutional Repository at Robert Gordon University (Robert Gordon University) (submittedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
Keywords
Ti-6Al-4V, titanium alloy machining, dry machining, machinability, cutting parameters, cutting power, surface roughness, material removal rate, uncoated cutting tools, tool wear, cutting speed, feed rate, Taguchi method, regression models

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.