Plasma processes inside dispenser hollow cathodes
The DOI matches its Crossref record; 8 of the 8 references it cites were found in a registry or an index.
Abstract
A two-dimensional fluid model of the plasma and neutral gas inside dispenser orificed hollow cathodes has been developed to quantify plasma processes that ultimately determine the life of the porous emitters inserted in these devices. The model self-consistently accounts for electron emission from the insert as well as for electron and ion flux losses from the plasma. Two cathodes, which are distinctively different in size and operating conditions, have been simulated numerically. It is found that the larger cathode, with outer tube diameter of 1.5cm and orifice diameter of 0.3cm, establishes an effective emission zone that spans approximately the full length of the emitter when operated at a discharge current of 25A and a flow rate of 5.5sccm. The net heating of the emitter is caused by ions that are produced by ionization of the neutral gas inside the tube and are then accelerated by the sheath along the emitter. The smaller cathode, with an outer diameter of 0.635cm and an orifice diameter of 0.1cm, does not exhibit the same operational characteristics. At a flow rate of 4.25sccm and discharge current of 12A, the smaller cathode requires 4.5 times the current density near the orifice and operates with more than 6 times the neutral particle density compared to the large cathode. As a result, the plasma particle density is almost one order of magnitude higher compared to the large cathode. The plasma density in this small cathode is high enough such that the Debye length is sufficiently small to allow “sheath funneling” into the pores of the emitter. By accessing areas deeper into the insert material, it is postulated that the overall emission of electrons is significantly enhanced. The maximum emission current density is found to be about 1A∕mm2 in the small cathode, which is about one order of magnitude higher than attained in the large cathode. The effective emission zone in the small cathode extends to about 15% of the emitter length only, and the power deposited at the emitter surface by returning electrons is found to be twice that deposited by ions. A previous study suggested that the computed particle flux and energy of ions to the emitter of the 1.5cm cathode were not high enough to change the barium evaporation rate compared to thermally induced evaporation. The same suggestion is made here for the 0.635cm cathode. The peak ion flux to the emitter is found to be 1.2A∕cm2 (7.6×1018∕scm2), and the corresponding peak sheath drop is 2.9V. Consequently, once the emitter operating temperature is known it is possible to determine directly the barium depletion-limited life of these cathodes using existing vacuum-cathode data.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“For small orifice diameters, the heating of the hollow cathode is predominantly due to Joule heating in the orifice region because of the current passing through the small diameter [8, 29, 30].”
From Computational modelling of water-fuelled Hall Effect Thrusters (2025) · cites this paper as [29]
Citations
Cites
Molecular Gas Dynamics And The Direct Simulation Of Gas Flows
Bird, G. A. (1994) · doi:10.1093/oso/9780198561958.001.0001 · Cited by 7,269
Plasma Physics via Computer Simulation
Birdsall, C. K., & Langdon, A. B. (2018) · CRC Press eBooks · doi:10.1201/9781315275048 · Cited by 3,745
Electron Emission from Metals as a Function of Temperature
Dushman, S. (1923) · Physical Review · doi:10.1103/physrev.21.623 · Cited by 288
Hollow cathode theory and experiment. II. A two-dimensional theoretical model of the emitter region
Mikellides, I. G., Katz, I., Goebel, D. M., & Polk, J. E. (2005) · Journal of Applied Physics · doi:10.1063/1.2135409 · Cited by 162
Self-citationDeterministic convergence of a self-tuning regulator with variable forgetting factor
Osorio-Cordero, A., & Mayne, D. Q. (1981) · IEE Proceedings D Control Theory and Applications · doi:10.1049/ip-d.1981.0004 · Cited by 121
One-Dimensional Hollow Cathode Model
Katz, I., Anderson, J. R., Polk, J. E., & Brophy, J. R. (2003) · Journal of Propulsion and Power · doi:10.2514/2.6146 · Cited by 61
Self-citationof Plasma Contactor Performance
Katz, I. M., Gardner, B. M., Mandell, M. J., Jongeward, G. A., Patterson, M., & Myers, R. (1997) · Journal of Spacecraft and Rockets · doi:10.2514/2.3294 · Cited by 31
Self-citationPhenomenological model describing orificed, hollow cathode operation
Siegfried, D. E., & Wilbur, P. J. (1983) · AIAA Journal · doi:10.2514/3.8022 · Cited by 24
Research works printed but not linked: 17
- 2003, 39th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2003, 39th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 1978, 13th AIAA/DGLR International Electric Propulsion Conference
- 2004, 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2005, 41st AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2004, 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2002, 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2002, 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 1997, 33rd AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2004, 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- A. Salhi, Ph.D. thesis, The Ohio State University, 1993.
- 1992, 28th SAE/ASME/ASEE, Joint Propulsion Conference and Exhibit
- 2003, 33rd AIAA Fluid Dynamics Conference and Exhibit
- 2003, Proceedings of 28th International Electric Propulsion Conference
- 2005, 41st AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2004, 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
- 2004, 40th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit
Cited by
Potential fluctuations and energetic ion production in hollow cathode discharges
Goebel, D. M., Jameson, K. K., Katz, I., & Mikellides, I. G. (2007) · Physics of Plasmas · doi:10.1063/1.2784460 · Cited by 151
Self-citationLaB6 Hollow Cathodes for Ion and Hall Thrusters
Goebel, D. M., Watkins, R. M., & Jameson, K. K. (2007) · Journal of Propulsion and Power · doi:10.2514/1.25475 · Cited by 143
Self-citationRecent progress in research and development of hollow cathodes for electric propulsion
Lev, D. R., Mikellides, I. G., Pedrini, D., Goebel, D. M., Jorns, B., & McDonald, M. (2019) · Reviews of Modern Plasma Physics · doi:10.1007/s41614-019-0026-0 · Cited by 125
Self-citationGoebel, D. M., Becatti, G., Mikellides, I. G., & Lopez Ortega, A. (2021) · Journal of Applied Physics · doi:10.1063/5.0051228 · Cited by 95
Self-citationWear Mechanisms in Electron Sources for Ion Propulsion, I: Neutralizer Hollow Cathode
Mikellides, I. G., & Katz, I. (2008) · Journal of Propulsion and Power · doi:10.2514/1.33461 · Cited by 89
Self-citationCompact lanthanum hexaboride hollow cathode
Goebel, D. M., & Watkins, R. M. (2010) · Review of Scientific Instruments · doi:10.1063/1.3474921 · Cited by 92
Self-citationHollow cathode modeling: I. A coupled plasma thermal two-dimensional model
Sary, G., Garrigues, L., & Boeuf, J.-P. (2017) · Plasma Sources Science and Technology · doi:10.1088/1361-6595/aa6217 · Cited by 71
Wall Sheath and Electron Mobility Modeling in Hybrid-PIC Hall Thruster Simulations
Hofer, R. R., Mikellides, I. G., Katz, I. M., & Goebel, D. M. (2007) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2007-5267 · Cited by 65
Self-citationHollow cathode modeling: II. Physical analysis and parametric study
Sary, G., Garrigues, L., & Boeuf, J.-P. (2017) · Plasma Sources Science and Technology · doi:10.1088/1361-6595/aa6210 · Cited by 57
“21 3 ́ - This behavior is in agreement with experimental measurements (see figure 2) and earlier studies about this cathode published in the literature [8, 9].”
BackgroundMethodResultInfluentialNumerical Simulations of the Partially Ionized Gas in a 100-A LaB6 Hollow Cathode
Mikellides, I. G., Goebel, D. M., Jorns, B. A., Polk, J. E., & Guerrero, P. (2015) · IEEE Transactions on Plasma Science · doi:10.1109/tps.2014.2320876 · Cited by 48
Self-citationTwo-dimensional model of orificed micro-hollow cathode discharge for space application
Levko, D., Krasik, Y. E., Vekselman, V., & Haber, I. I. (2013) · Physics of Plasmas · doi:10.1063/1.4818969 · Cited by 43
Effects of viscosity in a partially ionized channel flow with thermionic emission
Mikellides, I. G. (2009) · Physics of Plasmas · doi:10.1063/1.3056397 · Cited by 39
Self-citationA Reduced-Order Model for Thermionic Hollow Cathodes
Albertoni, R., Pedrini, D., Paganucci, F., & Andrenucci, M. (2013) · IEEE Transactions on Plasma Science · doi:10.1109/tps.2013.2266512 · Cited by 39
Dynamics of a hollow cathode discharge in the frequency range of 1–500 kHz
Mikellides, I. G., Ortega, A. L., Goebel, D. M., & Becatti, G. (2020) · Plasma Sources Science and Technology · doi:10.1088/1361-6595/ab69e4 · Cited by 38
Self-citationTransition characteristics of low-pressure discharges in a hollow cathode
Fu, Y., Verboncoeur, J. P., Christlieb, A., & Wang, X. (2017) · Physics of Plasmas · doi:10.1063/1.4997764 · Cited by 36
Examination of a 5 A-class cathode with a LaB6 flat disk emitter in the 2 A–20 A current range
Joussot, R., Grimaud, L., & Mazouffre, S. (2017) · Vacuum · doi:10.1016/j.vacuum.2017.09.021 · Cited by 37
Cao, S., Ren, J., Tang, H., Zhang, Z., Wang, Y., Cao, J., & Chen, Z. (2018) · Physics of Plasmas · doi:10.1063/1.5029945 · Cited by 34
Tungsten and barium transport in the internal plasma of hollow cathodes
Polk, J. E., Mikellides, I. G., Katz, I. M., & Capece, A. M. (2009) · Journal of Applied Physics · doi:10.1063/1.3111970 · Cited by 29
Self-citationCharacterization of Hollow Cathode Performance and Thermal Behavior
Polk, J. E., Goebel, D. M., Watkins, R. M., Jameson, K. K., & Yoneshige, L. (2006) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2006-5150 · Cited by 37
Self-citationModeling on plasma energy balance and transfer in a hollow cathode
Cao, S., Ren, J., Tang, H., Pan, R., Zhang, Z., Zhang, K., & Cao, J. (2019) · Journal of Physics D Applied Physics · doi:10.1088/1361-6463/ab197e · Cited by 25
2-D Modeling of Orificed Hollow Cathodes of Stationary Plasma Thrusters SPT-100
Liu, H., Li, M., Ning, Z., Ren, J., Tang, H., Yu, D., Demidov, E. V., Eliseev, S. I., & Kudryavtsev, A. A. (2015) · IEEE Transactions on Plasma Science · doi:10.1109/tps.2015.2457677 · Cited by 23
A Critical Review of Orificed Hollow Cathode Modeling: 0D Models
Wordingham, C. J., Taunay, P.-Y., & Choueiri, E. (2017) · AIAA/SAE/ASEE Joint Propulsion Conference (JPC) · doi:10.2514/6.2017-4888 · Cited by 17
The Effect of Reactive Gases on Hollow Cathode Operation
Polk, J. E. (2006) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2006-5153 · Cited by 19
Self-citationMikellides, I. G., & Katz, I. M. (2007) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2007-5168 · Cited by 14
Self-citationQualification of Commercial XIPS Ion Thrusters for NASA Deep Space Missions
Goebel, D. M., Polk, J., Wirz, R. E., Snyder, J., Mikellides, I. G., Katz, I. M., & Anderson, J. R. (2008) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2008-4914 · Cited by 12
Self-citationDevelopment and Testing of High Current Hollow Cathodes for High Power Hall Thrusters
Kamhawi, H., & Noord, J. V. (2012) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2012-4080 · Cited by 12
Ortega, A. L., Jorns, B., Mikellides, I. G., & Hofer, R. R. (2015) · AIAA/SAE/ASEE Joint Propulsion Conference (JPC) · doi:10.2514/6.2015-4008 · Cited by 11
Self-citationA Parametric Study of Electron Extraction from a Low Frequency Inductively Coupled RF-Plasma Source
Raitses, Y., Hendryx, J., & Fisch, N. J. (2009) · Cited by 7
Physics of thermionic, orificed hollow cathodes: I. Theory and experimental validation
Taunay, P.-Y., Wordingham, C. J., & Choueiri, E. (2022) · Plasma Sources Science and Technology · doi:10.1088/1361-6595/ac5c63 · Cited by 9
Experiment and analysis of the neutralization of the electron cyclotron resonance ion thruster
Jin, Y., Yang, J., Sun, J., Liu, X., & Huang, Y. (2017) · Plasma Science and Technology · doi:10.1088/2058-6272/aa76d9 · Cited by 6
The attachment length in orificed hollow cathodes
Wordingham, C. J., Taunay, P.-Y., & Choueiri, E. (2021) · Plasma Sources Science and Technology · doi:10.1088/1361-6595/ac3d3f · Cited by 5
Modélisation d'une cathode creuse pour propulseur à plasma
Sary, G. (2016) · theses.fr (ABES) · doi:10.70675/9aee20b5ze30fz430ezac81z6bf48413107e · Cited by 6
Martens, P. D., Barton, D. A. W., Schartner, A. P., Charles, C., & Boswell, R. W. (2025) · Journal of Electric Propulsion · doi:10.1007/s44205-025-00115-3 · Cited by 4
Establishing criteria for the transition from kinetic to fluid modeling in hollow cathode analysis
Villafana, W., Powis, A. T., Sharma, S., Kaganovich, I., & Khrabrov, A. V. (2024) · Physics of Plasmas · doi:10.1063/5.0213313 · Cited by 7
Molybdenum erosion in iodine plasma at hollow cathode conditions
Rogers, J. D., & Branam, R. D. (2024) · Journal of Vacuum Science & Technology A Vacuum Surfaces and Films · doi:10.1116/6.0003367 · Cited by 4
Numerical simulation and experimental research on an inductively coupled RF plasma cathode
Xu, Z., Wang, P., Hua, Z., Cong, S., & Yu, S. (2021) · Plasma Science and Technology · doi:10.1088/2058-6272/ac337a · Cited by 3
Tungsten and Barium Transport in the Internal Plasma of Hollow Cathodes
Polk, J. E., Mikellides, I. G., Katz, I. M., & Capece, A. M. (2008) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit (JPC) · doi:10.2514/6.2008-5295 · Cited by 3
Self-citationGeneration of anomalously energetic ions in hollow cathode plume via charge separation instability
Zhao, Y., Wang, B., & Meng, T. (2025) · Plasma Science and Technology · doi:10.1088/2058-6272/ae0bb0 · Cited by 3
Cao, L., Chen, Z., Luo, Z., Zhang, G., Ren, J., Wang, Y., Mao, R., Luo, W., Wu, K., Wang, C., et al. (2025) · Plasma Sources Science and Technology · doi:10.1088/1361-6595/adf574 · Cited by 2
Plasma characteristics in the discharge region of a 20 A emission current hollow cathode
Sun, M., ZHANG, T., Wen, X., Guo, W., & Song, J. (2017) · Plasma Science and Technology · doi:10.1088/2058-6272/aa8edb · Cited by 2
One-Dimensional Model for Hollow Cathode Orifice Lifetime Prediction
Bosi, F. J., Guarducci, F., & Gabriel, S. B. (2021) · Journal of Propulsion and Power · doi:10.2514/1.b38094 · Cited by 2
Rarefied xenon flow in orificed hollow cathodes
Taunay, P.-Y., Villafana, W., Vinoth, S. P., Kaganovich, I., & Khodak, A. E. (2025) · Journal of Applied Physics · doi:10.1063/5.0249172 · Cited by 1
Guerrero, P., Polk, J. E., Lobbia, R. B., & Mikellides, I. G. (2018) · AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit · doi:10.2514/6.2018-4511
Self-citationDispenser Hollow Cathode Discharges
Capece, A. M. (2016) · CRC Press eBooks · doi:10.1081/e-eplt-120053933
Scaling Relationships for the Total Pressure in Orificed Hollow Cathodes
Taunay, P.-Y., Wordingham, C. J., & Choueiri, E. (2019) · AIAA Propulsion and Energy Forum · doi:10.2514/6.2019-4246
Sun, M., Liu, C., & Gu, Z. (2021) · Journal of Aerospace Technology and Management · doi:10.1590/jatm.v13.1235
Metadata
- Authors
- Mikellides, I. G., Katz, I., Goebel, D. M., Polk, J. E., & Jameson, K. K.
- Affiliations
- California Institute of Technology (US)
- Venue
- Physics of Plasmas
- Publisher
- AIP Publishing
- Published
- 2006-06-01
- Volume
- 13
- Issue
- 6
- ISSN
- 1070-664X (ISSN-L)
- 1089-7674
- OpenAlex
- W2048362983
- Cited by
- 46
- References
- 8
- Citations by year
- 2025: 4 · 2024: 2 · 2022: 1 · 2021: 5 · 2020: 1 · 2019: 3 · 2018: 2 · 2017: 7 · 2016: 1 · 2015: 2 · 2014: 1 · 2013: 2 · 2012: 1
- FWCI
- 4.38
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Physics of Plasmas (publishedVersion)
- Funders
- National Aeronautics and Space Administration
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Low-Pressure Plasma Processing and Diagnostics
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Vacuum and Plasma Arcs
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Gyrotron and Vacuum Electronics Research
- Keywords
- electron emission, Debye length, barium evaporation, two-dimensional hydrodynamic model, plasma density, electric thrusters, discharge current density
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.